Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2019.09–2022.01
RM32K0E _58 Vehicle Interior _062267 SUPPLEMENTAL RESTRAINT SYSTEMS _0304666 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1635  Curtain Shield Airbag Sensor (LH)  B1637  Curtain Shield Airbag Sensor Lost Communication (LH)  


DESCRIPTION

The side collision sensor LH circuit (bus 1) consists of the airbag sensor assembly, door side airbag sensor LH and No. 2 side airbag sensor LH.

The door side airbag sensor LH and No. 2 side airbag sensor LH detect impacts to the vehicle and send signals to the airbag sensor assembly to determine if the airbags and pretensioners should be deployed.

These DTCs are stored when a malfunction is detected in the No. 2 side airbag sensor LH.

DTC No. Detection Item DTC Detection Condition Trouble Area Test Mode / Check Mode
B1635 Curtain Shield Airbag Sensor (LH)
·

No. 2 side airbag sensor LH malfunction

·

Airbag sensor assembly malfunction


·

No. 2 side airbag sensor LH

·

Airbag sensor assembly


Does not apply to test/check mode
B1637 Curtain Shield Airbag Sensor Lost Communication (LH)
·

No. 2 side airbag sensor LH malfunction

·

Airbag sensor assembly malfunction


·

No. 2 side airbag sensor LH

·

Airbag sensor assembly


Does not apply to test/check mode

DTC Detection Conditions (B1635):
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition Power switch on (IG) ○ ○
Malfunction Status No. 2 side airbag sensor LH malfunction ○ -
Airbag sensor assembly malfunction - ○
Detection Time - -
Number of Trips 1 trip 1 trip

DTC Detection Conditions (B1637):
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition Power switch on (IG) ○ ○
Malfunction Status No. 2 side airbag sensor LH malfunction ○ -
Airbag sensor assembly malfunction - ○
Detection Time - -
Number of Trips 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


CAUTION / NOTICE / HINT

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

1.CHECK NO. 2 SIDE AIRBAG SENSOR LH
a.
C238328C01
0.719,0.813 1.073,1.24 0.354,0.427 10 false *1 1.104,0.813 1.354,1.25 0.25,0.438 10 false D 1.26,0.813 1.573,1.167 0.313,0.354 10 false C 1.729,0.813 2.031,1.073 0.302,0.26 10 false B 1.885,0.813 2.135,1.073 0.25,0.26 10 false A 2.323,1.135 2.646,1.385 0.323,0.25 10 false *2
*1 No. 2 Side Airbag Sensor RH
*2 Airbag Sensor Assembly


Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Interchange the No. 2 side airbag sensor LH with RH and connect the connectors.


d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Turn the power switch on (IG), and wait for at least 60 seconds.


f.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 188

g.

Turn the power switch off.


h.

Turn the power switch on (IG), and wait for at least 60 seconds.


i.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B1630, B1632, B1635 and B1637 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTC B1635 or B1637 is output. A
DTC B1630 or B1632 is output. B
DTCs B1630, B1632, B1635 and B1637 are not output. C


j.

Turn the power switch off.


k.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



l.

Return the No. 2 side airbag sensor LH and RH to their original positions and connect the connectors.



A

B

C