Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2019.09
RM32K0E _58 Vehicle Interior _062267 SUPPLEMENTAL RESTRAINT SYSTEMS _0304666 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1651  Manual Cut OFF Switch Trouble  


DESCRIPTION

The airbag cut off switch circuit consists of the airbag sensor assembly and airbag cut off switch cylinder sub-assembly.

The instrument panel passenger airbag assembly can be optionally deactivated via this circuit by turning the airbag cut off switch cylinder sub-assembly to the OFF position.

If the instrument panel passenger airbag assembly is deactivated, the passenger airbag ON/OFF indicator ("OFF") comes on to inform the driver.

DTC B1651 is stored when a malfunction is detected in the airbag cut off switch circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Test Mode / Check Mode
B1651 Manual Cut OFF Switch Trouble
·

The airbag sensor assembly detects a line short in the airbag cut off switch circuit.

·

The airbag sensor assembly detects a short to ground in the airbag cut off switch circuit.

·

The airbag sensor assembly detects a short to B+ in the airbag cut off switch circuit.

·

The airbag sensor assembly detects an open in the airbag cut off switch circuit.

·

Airbag cut off switch cylinder sub-assembly malfunction

·

Airbag sensor assembly malfunction


·

Instrument panel wire

·

Airbag cut off switch cylinder sub-assembly

·

Airbag sensor assembly


Does not apply to test/check mode

DTC Detection Conditions:
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4 Pattern 5 Pattern 6
Diagnosis Condition Power switch on (IG) ○ ○ ○ ○ ○ ○
Malfunction Status The airbag sensor assembly detects a line short in the airbag cut off switch circuit ○ - - - - -
The airbag sensor assembly detects a short to ground in the airbag cut off switch circuit - ○ - - - -
The airbag sensor assembly detects a short to B+ in the airbag cut off switch circuit - - ○ - - -
The airbag sensor assembly detects an open in the airbag cut off switch circuit - - - ○ - -
Airbag cut off switch cylinder sub-assembly malfunction - - - - ○ -
Airbag sensor assembly malfunction - - - - - ○
Detection Time - - - - - -
Number of Trips 1 trip 1 trip 1 trip 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


WIRING DIAGRAM

B512690E09
4.854,2.979 5.479,3.177 0.625,0.198 10 false F150 4.844,3.146 6.583,3.542 1.74,0.396 10 false Airbag Sensor Assembly 0.542,2.823 1.177,3 0.635,0.177 10 false F64 0.542,2.99 3.542,3.292 3,0.302 10 false Airbag Cut Off Switch Cylinder Sub-assembly 2.219,1.115 2.802,1.448 0.583,0.333 10 false 2 1.729,1.115 2.313,1.448 0.583,0.333 10 false PMC+ 1.75,2.302 2.333,2.635 0.583,0.333 10 false PMC- 2.208,2.302 2.792,2.635 0.583,0.333 10 false 1 4.885,1.104 5.469,1.438 0.583,0.333 10 false MSW+ 4.635,1.104 5.219,1.438 0.583,0.333 10 false 22 4.885,2.302 5.469,2.635 0.583,0.333 10 false MSW- 4.635,2.302 5.219,2.635 0.583,0.333 10 false 21

CAUTION / NOTICE / HINT

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

1.CHECK CONNECTION OF CONNECTORS
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag sensor assembly and airbag cut off switch cylinder sub-assembly.

OK:

The connectors are properly connected.



Result:
Proceed to
OK
NG



OK

2.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

2.CHECK CONNECTORS
a.

Disconnect the connectors from the airbag sensor assembly and airbag cut off switch cylinder sub-assembly.


b.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

3.CHECK INSTRUMENT PANEL WIRE

NG

REPLACE INSTRUMENT PANEL WIRE

3.CHECK INSTRUMENT PANEL WIRE
a.
B512677C08
0.75,0.854 1.167,1.083 0.417,0.229 0.531,3.74 0.896,3.958 0.365,0.219 1.458,2.604 1.458,2.104 1.458,2.104 1.292,2.104 false 1.792,1.729 1.792,1.604 false 1.292,1.594 1.76,1.094 true 2.281,1.594 1.833,1.094 true 0.99,4.26 1.229,3.927 true 1.688,4.26 1.479,3.927 true 0.448,2.573 0.854,2.979 0.406,0.406 10 false *1 2.552,2.563 3.073,3.208 0.521,0.646 10 false *2 1.094,2.021 1.469,2.406 0.375,0.385 10 false *3 1.729,1.74 2.125,1.979 0.396,0.24 10 false *4 0.667,0.198 1.073,0.542 0.406,0.344 10 false *a 0.375,3.406 0.792,3.719 0.417,0.313 10 false *b 2.177,2.563 2.698,3.208 0.521,0.646 10 false A 1.813,2.563 2.333,3.208 0.521,0.646 10 false B 1.063,2.573 1.583,3.219 0.521,0.646 10 false C 0.698,2.573 1.219,3.219 0.521,0.646 10 false D 0.802,0.885 1.208,1.229 0.406,0.344 10 false F150 1.115,1.604 1.604,1.99 0.49,0.385 10 false MSW- 2.125,1.604 2.667,2.01 0.542,0.406 10 false MSW+ 1.563,4.271 2.177,4.604 0.615,0.333 10 false PMC+ 0.833,4.271 1.448,4.604 0.615,0.333 10 false PMC- 0.594,3.771 1,4.115 0.406,0.344 10 false F64
*1 Airbag Cut Off Switch Cylinder Sub-assembly
*2 Airbag Sensor Assembly
*3 Instrument Panel Wire
*4 Service Wire
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of wire harness connector
(to Airbag Cut Off Switch Cylinder Sub-assembly)


Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F64-2 (PMC+) - Body ground Power switch on (IG) Below 1 V
F64-1 (PMC-) - Body ground Power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



f.

Using a service wire, connect terminals 22 (MSW+) and 21 (MSW-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F64-2 (PMC+) - F64-1 (PMC-) Always Below 1 Ω



h.

Disconnect the service wire from connector B.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F64-2 (PMC+) - F64-1 (PMC-) Always 1 MΩ or higher
F64-2 (PMC+) - Body ground Always 1 MΩ or higher
F64-1 (PMC-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT AIRBAG CUT OFF SWITCH CYLINDER SUB-ASSEMBLY

NG

REPLACE INSTRUMENT PANEL WIRE

4.INSPECT AIRBAG CUT OFF SWITCH CYLINDER SUB-ASSEMBLY
a.

Remove the airbag cut off switch cylinder sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG CUT-OFF SWITCH>REMOVAL


b.

Inspect the airbag cut off switch cylinder sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG CUT-OFF SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

5.CHECK DTC

NG

REPLACE AIRBAG CUT OFF SWITCH CYLINDER SUB-ASSEMBLY

5.CHECK DTC
a.
C238224C02
0.802,1.01 1.573,1.542 0.771,0.531 10 *1 2.313,1.021 2.708,1.417 0.396,0.396 10 *2 1.875,1.01 2.417,1.458 0.542,0.448 10 A 1.719,1.01 2.219,1.427 0.5,0.417 10 B 1.271,1.01 1.688,1.427 0.417,0.417 10 C 1.115,1.01 1.688,1.5 0.573,0.49 10 D
*1 Airbag Cut Off Switch Cylinder Sub-assembly
*2 Airbag Sensor Assembly


Connect the connectors to the airbag sensor assembly and airbag cut off switch cylinder sub-assembly.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the power switch on (IG), and wait for at least 60 seconds.


d.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the power switch off.


f.

Turn the power switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1651 is not output.


HINT:

Codes other than DTC B1651 may be output at this time, but they are not related to this check.



Result:
Proceed to
OK
NG



OK

NG