Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type) › 2019.09–2022.01
RM32K0E _56 Audio / Visual / Telematics _061817 AUDIO / VIDEO _0301367 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  Data Signal Circuit between Radio Receiver and Stereo Jack Adapter  


DESCRIPTION

The No. 1 stereo jack adapter assembly sends the sound data signal or image data signal from a USB device to the radio and display receiver assembly via this circuit.

WIRING DIAGRAM

E360247E13
5.406,2.563 5.719,2.76 0.313,0.198 10 false j12 5.385,2.75 7.104,3.604 1.719,0.854 10 false Radio and Display Receiver Assembly 2.469,3.26 5.313,3.781 2.844,0.521 10 false : Data Signal (USB Communication Line) 0.469,2.865 1.615,3.781 1.146,0.917 10 false No. 1 Stereo Jack Adapter Assembly 0.479,2.677 0.792,2.875 0.313,0.198 10 false j11 3.25,1.75 4.781,1.948 1.531,0.198 10 false (Shielded) 5.906,0.646 7.156,0.875 1.25,0.229 10 false US1- 5.906,1.427 7.156,1.656 1.25,0.229 10 false US1+ 5.906,2.208 7.156,2.438 1.25,0.229 10 false USG1 5.698,0.5 5.854,0.698 0.156,0.198 10 false 2 5.688,1.292 5.844,1.49 0.156,0.198 10 false 3 5.708,2.094 5.865,2.292 0.156,0.198 10 false 5 1.354,0.51 1.51,0.708 0.156,0.198 10 false 2 1.344,1.313 1.5,1.51 0.156,0.198 10 false 3 1.333,2.104 1.49,2.302 0.156,0.198 10 false 5 0.896,0.656 1.281,1.104 0.385,0.448 10 false UDO- 0.854,1.469 1.281,1.917 0.427,0.448 10 false UDO+ 0.854,2.229 1.26,2.688 0.406,0.458 10 false UJSS

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 1 STEREO JACK ADAPTER ASSEMBLY)
a.

Disconnect the j12 radio and display receiver assembly connector.


b.

Disconnect the j11 No. 1 stereo jack adapter assembly connector.


c.
E420208C45
1.542,2.438 1.958,2.688 0.417,0.25 1.563,0.24 1.979,0.49 0.417,0.25 2.208,2.198 1.854,1.75 true 1.917,1.594 2.333,1.74 true 1.063,1.948 1.531,1.594 true 1.792,3.844 2.125,4.26 true 1.917,3.656 2.521,3.479 true 1.51,3.656 1.104,3.875 true 0.24,0.188 0.552,0.385 0.313,0.198 10 false *a 0.24,2.802 0.552,3 0.313,0.198 10 false *b 0.677,1.854 1.104,2.063 0.427,0.208 10 false US1+ 2.24,2.135 2.729,2.375 0.49,0.24 10 false USG1 2.375,1.677 2.792,1.927 0.417,0.25 10 false US1- 2.573,3.417 2.969,3.677 0.396,0.26 10 false UDO- 2.167,4.198 2.667,4.458 0.5,0.26 10 false UJSS 0.698,3.802 1.135,4.063 0.438,0.26 10 false UDO+ 1.688,0.26 2.146,0.458 0.458,0.198 10 false j12 1.646,2.458 1.958,2.656 0.313,0.198 10 false j11
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)
*b Front view of wire harness connector
(to No. 1 Stereo Jack Adapter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
j12-2 (US1-) - j11-2 (UDO-) Always Below 1 Ω
j12-3 (US1+) - j11-3 (UDO+) Always Below 1 Ω
j12-5 (USG1) - j11-5 (UJSS) Always Below 1 Ω
j12-2 (US1-) - Body ground Always 10 kΩ or higher
j12-3 (US1+) - Body ground Always 10 kΩ or higher
j12-5 (USG1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR