1.INSPECT AND ADJUST BRAKE PEDAL HEIGHT
Remove the No. 1 air duct.
Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL
Check the brake pedal height.
Inspect and adjust the brake pedal height with the floor carpet folded back.
When performing the measurement, make sure that the measuring device is contacting the surface of the dash panel insulator assembly clip.
Measure the shortest distance between the brake pedal pad surface and dash panel insulator assembly clip.
| *1 | Brake Pedal Pad | *2 | Dash Panel Insulator Assembly Clip |
| *a | Brake Pedal Height | - | - |
176.0 to 188.0 mm (6.93 to 7.40 in.)
If the pedal height is not as specified, adjust the brake pedal height according to the procedure below.
Adjust the brake pedal height.
| *1 | Stop Light Switch Assembly |
| *2 | Clevis Lock Nut |
| *3 | Dash Panel Insulator Assembly Clip |
| *a | Brake Pedal Height |
Remove the stop light switch assembly.
Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL
Loosen the clevis lock nut.
Adjust the brake pedal height by turning the push rod.
176.0 to 188.0 mm (6.93 to 7.40 in.)
Tighten the clevis lock nut.
Install the stop light switch assembly.
Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSTALLATION
Install the No. 1 air duct.
Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSTALLATION
89510D
2.INSPECT AND ADJUST BRAKE PEDAL STROKE SENSOR ASSEMBLY
Inspect the brake pedal stroke sensor assembly.
Connect the GTS to the DLC3 with the power switch off.
Turn the power switch on (IG).
Turn the GTS on and enter the following menus: Chassis / ABS/VSC/TRC / Data List / Stroke Sensor.
| Tester Display |
|---|
| Stroke Sensor |
Read the stroke sensor value without the brake pedal depressed.
0.8 to 1.2 V
If the stroke sensor value is not within the standard voltage, adjust the brake pedal stroke sensor assembly.
Adjust the brake pedal stroke sensor assembly.
Remove the No. 1 air duct.
Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL
Loosen the 2 nuts.
Do not depress the brake pedal after turning the power switch on (IG).
Read the stroke sensor value in the Data List, and turn the brake pedal stroke sensor assembly slowly to the right or left to adjust the output voltage so that it is within the following range.
0.8 to 1.2 V
Tighten the 2 nuts.
Perform linear solenoid valve offset learning, ABS holding solenoid valve learning, brake pedal stroke sensor assembly zero point calibration and system information memorization.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>CALIBRATION
Turn the GTS off and turn the power switch off.
Disconnect the GTS.
Install the No. 1 air duct.
Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSTALLATION
3.INSPECT BRAKE PEDAL FREE PLAY
| *a | Brake Pedal Free Play |
Depress the brake pedal until a slight resistance is felt. Measure the brake pedal free play as shown in the illustration.
1.0 to 6.0 mm (0.0394 to 0.236 in.)
If the pedal free play is not as specified, check the stop light switch clearance.
Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSTALLATION
If the pedal free play is as specified, proceed to the Inspect Brake Pedal Reserve Distance procedure.
4.INSPECT BRAKE PEDAL RESERVE DISTANCE
Remove the front door scuff plate LH.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>REAR CONSOLE BOX>REMOVAL
Remove the cowl side trim board LH.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>REAR CONSOLE BOX>REMOVAL
Remove the No. 1 instrument panel under cover sub-assembly.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>REAR CONSOLE BOX>REMOVAL
Remove the console box insert.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>REAR CONSOLE BOX>REMOVAL
Turn back the front floor carpet assembly.
With the power switch on (READY), depress the brake pedal and measure the brake pedal reserve distance as shown in the illustration.
| *1 | Brake Pedal Pad | *2 | Column Hole Cover Silencer Sheet |
| *a | Brake Pedal Reserve Distance | *b | Measuring Plane of Column Hole Cover Silencer Sheet |
| *c | 70 mm (2.76 in.) | - | - |
134 mm (5.28 in.) or more
If the distance is not as specified, troubleshoot the brake system.
Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE
Install the front floor carpet assembly to its original position.
Install the console box insert.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>REAR CONSOLE BOX>INSTALLATION
Install the No. 1 instrument panel under cover sub-assembly.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>REAR CONSOLE BOX>INSTALLATION
Install the cowl side trim board LH.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>REAR CONSOLE BOX>INSTALLATION
Install the front door scuff plate LH.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>REAR CONSOLE BOX>INSTALLATION