Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM › 2019.09–2022.01
RM32K0E _56 Audio / Visual / Telematics _060599 PARK ASSIST / MONITORING _0410446 PANORAMIC VIEW MONITOR SYSTEM D

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM  DIAGNOSIS SYSTEM  


PARKING ASSIST MONITOR DIAGNOSIS SYSTEM


a.

For panoramic view monitor system diagnosis, signals received by the parking assist ECU can be checked, and the panoramic view monitor system can be calibrated, adjusted and checked using the radio and display receiver assembly.

NOTICE:

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>CALIBRATION


HINT:

The displayed screens and items may differ depending on vehicle specifications.




DIAGNOSIS SCREEN TRANSITION (VIEW ADJUSTMENT)


E428358E03
2.781,0.927 5.99,1.125 3.208,0.198 10 false Start diagnostic mode


DIAGNOSIS SCREEN TRANSITION (STEERING ANGLE SETTING)


E428359E03
2.781,0.979 5.99,1.177 3.208,0.198 10 false Start diagnostic mode 5.583,5.167 5.781,5.365 0.198,0.198 10 false or


DIAGNOSIS SCREEN TRANSITION (CAMERA CHECK)


E403250E02
2.771,0.969 5.979,1.167 3.208,0.198 10 false Start diagnostic mode


DIAGNOSIS SCREEN TRANSITION (DIAG CHECK)


E403251E02
2.76,0.979 5.969,1.177 3.208,0.198 10 false Start diagnostic mode



SIGNAL CHECK (parking assist ECU input signal)


a.

Start diagnostic mode.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR

i.
E366768

Select "Function Check/Setting" on the "Service Menu" screen to display the "Function Check/Setting I" screen.


ii.
E366769E01
0.146,0.104 1.375,0.302 1.229,0.198 10 false Example:

Select "Camera Setting" on the "Function Check/Setting I" screen.

HINT:

After "Camera Setting" is selected, the screen transitions differ depending on whether initialization of the parking assist ECU was performed after parking assist ECU replacement.

Parking Assist ECU Initialization Screen Transition
Not performed "Signal Check" screen
Performed "Mode Setting" screen



iii.
E403246

When the screen changes to the "Mode Setting" screen, select "View Adjustment" to display the "Signal Check" screen.

HINT:

To select a grayed out item, select and hold the item for 2 seconds or more.




b.

Signal check

i.
E428278

On the "Signal Check" screen, it is possible to inspect the state of signals sent to the parking assist ECU and check the settings.

Item Inspection Detail Note
CAN Speed signal input When "CHK" (red) is displayed, selecting "Next" will not change to the next screen.
SHIFT Shift position signal input

HINT:
·

When "CHK" (red) is displayed, perform inspections based on the result of the following inspections.

·

If performing the adjustment after proceeding to the next screen, check that all items display "OK" (blue) before selecting "Next".





c.

CAN inspection

HINT:

If "CHK" (red) is displayed for "CAN", check for DTCs and perform troubleshooting based on the output DTCs.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>"CHK" message(s) are displayed on the SIGNAL CHECK screen.



d.

SHIFT inspection

HINT:

If "CHK" (red) is displayed for "SHIFT", check for DTCs and perform troubleshooting based on the output DTCs.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>"CHK" message(s) are displayed on the SIGNAL CHECK screen.



e.

CAMERA SW inspection

i.

Check that "OK" (blue) is displayed for "CAMERA SW" and select "OK".

HINT:

If "CHK" (red) remains displayed or the "CAMERA SW" inspection result is not normal, perform troubleshooting according to the Problem Symptoms Table ("CHK" message(s) are displayed on the "Signal Check" screen).

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>"CHK" message(s) are displayed on the SIGNAL CHECK screen.






CAMERA CHECK


HINT:
·

Use this function when symptoms such as the camera images not being displayed occur.

·

On the DTC screen, the 4 camera images are displayed as one image and the images input to the parking assist ECU from the cameras can be checked.



a.

Start diagnostic mode.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR

i.
E271944

Select "Function Check/Setting" on the "Service Menu" screen to display the "Function Check/Setting I" screen.


ii.
E364723

Select "Camera Setting" on the "Function Check/Setting I" screen.

NOTICE:

If the "Camera Setting" selection screen is not displayed, turn the power switch off and enter the diagnosis screen after turning the power switch on (IG) once again.


HINT:

After "Camera Setting" is selected, the screen transitions differ depending on whether initialization of the parking assist ECU was performed after parking assist ECU replacement.

Parking Assist ECU Initialization Screen Transition
Not performed "Signal Check (*)" screen
Performed "Mode Setting (*)" screen



iii.
E403246

When the screen changes to the "Mode Setting (*)" screen, select "View Adjustment" to display the "Signal Check (*)" screen.

HINT:

To select a grayed out item, select and hold the item for 2 seconds or more.




b.

Check camera images

i.
E376965

On the "Camera Check (*)" screen, the images that are input to the parking assist ECU from the 4 cameras are displayed on the screen and the camera images can be checked.

Indication Name Measurement Item Indication Name Measurement Item
Front Front television camera assembly Back Rear television camera assembly
Left Side television camera assembly LH Right Side television camera assembly RH





DIAG CHECK


a.

Start diagnostic mode.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR

i.
E271944

Select "Function Check/Setting" on the "Service Menu" screen.


ii.
E364723

Select "Camera Setting" on the "Function Check/Setting I" screen.

NOTICE:

If the "Camera Setting" selection screen is not displayed, turn the power switch off and enter the diagnosis screen after turning the power switch on (IG) once again.



iii.
E403246

Select "Diag Check" on the "Mode Setting (*)" screen to display the "Diag Check (*)" screen.

HINT:

To select a grayed out item, select and hold the item for 2 seconds or more.




b.

Check Diagnosis

i.

On the "Diag Check (*)" screen, DTCs output when the parking assist ECU detects a malfunction can be checked.

E376966

Indication Name Measurement Item Note
Present Diag Code Current DTC DTCs output when the parking assist ECU detects a malfunction
Past Diag Code Past DTC
PID PID table Values based on information displayed on Data List





CALIBRATION WHEN SERVICING VEHICLE


NOTICE:

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>CALIBRATION