Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM › from 2019.09
RM32K0E _56 Audio / Visual / Telematics _060599 PARK ASSIST / MONITORING _0410446 PANORAMIC VIEW MONITOR SYSTEM U

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM  DATA LIST / ACTIVE TEST  


DATA LIST


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / Circumference Monitoring Camera Control Module / Data List.


e.

Read the Data List according to the display on the GTS.

Chassis > Panoramic View Monitor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
HV/ENG Data Check Status of the HV/ENG data check Normal/Abnormal Normal: Parking assist ECU is normal
Abnormal: Parking assist ECU is abnormal
-
Display Drawing Function (Intuitive P/A Forward Detection) With or Without Comparing Rear television camera assembly drawing function (clearance sonar forward detection) with or without comparing Match or Mismatch Match: Rear television camera assembly normal
Mismatch: Rear television camera assembly abnormal
-
Main CPU Forced Termination Detection Record A history item indicating that the main CPU did not enter standby status within 15 seconds of turning the power switch off and a forced end was applied No/Yes No: Parking assist ECU is normal
Yes: Parking assist ECU is abnormal
-
Main CPU Abnormal Response Record A history item indicating that the main CPU became unresponsive in normal status No/Yes No: Parking assist ECU is normal
Yes: Parking assist ECU is abnormal
-
Main CPU Abnormal Reset Record A history item indicating that the main CPU was reset, although the power switch was not turned off in normal status No/Yes No: Parking assist ECU is normal
Yes: Parking assist ECU is abnormal
-
Image Processing IC Written Protect Record A history item indicating that the image processing IC memory was write protected No/Yes No: Parking assist ECU is normal
Yes: Parking assist ECU is abnormal
-
Image Processing IC Initialized Malfunction Record A history item indicating that the image processing IC memory was not initialized No/Yes No: Parking assist ECU is normal
Yes: Parking assist ECU is abnormal
-
Main EEPROM Access Status Main EEPROM access status Normal/Abnormal Normal: Parking assist ECU is normal
Abnormal: Parking assist ECU is abnormal
-
Sub EEPROM Access Status Sub-EEPROM access status Normal/Abnormal Normal: Parking assist ECU is normal
Abnormal: Parking assist ECU is abnormal
-
System Power Supply Voltage Malfunction Record A history item indicating an abnormally generated-voltage value from the system power source No/Yes No: Parking assist ECU is normal
Yes: Parking assist ECU is abnormal
-
Main CPU Starting Malfunction Record A history item indicating that the main CPU did not start No/Yes No: Parking assist ECU is normal
Yes: Parking assist ECU is abnormal
-
CAN CPU Boot Malfunction Record A history item indicating that the CPU controlling the input and output of the information obtained via CAN communication did not start and the information could not be retrieved No/Yes No: Parking assist ECU is normal
Yes: Parking assist ECU is abnormal
-
Visual Display Line Status Displays the status of the video signals displayed on the multi-display ON/OFF OK: GVIF cable is normal
NG: GVIF cable is abnormal
-
Wheel Speed Sensor (4wheel) Reception state of the vehicle speed signal from the skid control ECU (brake booster with master cylinder assembly) Valid/Invalid Valid: Speed signal received
Invalid: Speed signal not received
-
Continuous Bus Off Continuous bus off status (Global) Not Detected/Detected Not detected: Communication condition available
Detected: Communication condition not available
-
Sending CAN Message Communication condition from parking assist ECU (Global) OK/NG OK: Communication condition available
NG: Communication condition not available
-
Shift R Position Reverse signal ON/OFF OFF: Shift lever in any position except R
ON: Shift lever in R
-
Back Camera Availability Consistency Status of ECU stored in rear television camera assembly OK/NG OK: Normal
NG: Rear television camera assembly or parking assist ECU is abnormal
-
Side Camera LH Availability Consistency Status of ECU stored in side television camera assembly LH OK/NG OK: Normal
NG: Side television camera assembly LH or parking assist ECU is abnormal
-
Front Camera Availability Consistency Status of ECU stored in front television camera assembly OK/NG OK: Normal
NG: Front television camera assembly or parking assist ECU is abnormal
-
Side Camera RH Availability Consistency Status of ECU stored side television camera assembly RH OK/NG OK: Normal
NG: Side television camera assembly RH or parking assist ECU is abnormal
-
Image Adjustment Status Status of the image adjustment status Incomplete/Processing/Complete Incomplete: Image adjustment incomplete
Processing: Image adjustment in processing
Complete: Image adjustment completed
-
Number of DTC Number of DTCs (past and present) Min: 0, Max: 255 Changes according to the number of DTCs output -