Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM › from 2019.09
RM32K0E _56 Audio / Visual / Telematics _060599 PARK ASSIST / MONITORING _0410446 PANORAMIC VIEW MONITOR SYSTEM C

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM  C1625  Open or Short in Steering Angle Sensor +B  


DESCRIPTION

This DTC is stored if the parking assist ECU receives a signal via CAN communication from the steering sensor that indicates a power supply system problem.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1625 Open or Short in Steering Angle Sensor +B Open or short in steering angle sensor +B
·

Harness or connector

·

Steering sensor



WIRING DIAGRAM

B500635E09
3.177,2.177 3.719,2.417 0.542,0.24 10 false F69 3.177,2.344 4.365,2.604 1.188,0.26 10 false Steering Sensor 5.354,2.188 6.74,2.49 1.385,0.302 10 false Parking Assist ECU 1.104,3.219 2.99,3.5 1.885,0.281 10 false : CAN Communication Line 0.344,1.177 1.75,1.458 1.406,0.281 10 false from IG1-NO. 1 Relay 0.323,0.625 1.896,0.979 1.573,0.354 10 false from Auxiliary Battery 1.99,0.813 3.156,1.073 1.167,0.26 10 false ECU-DCC NO. 1 2.01,1.354 3.083,1.625 1.073,0.271 10 false ECU-IG1 NO. 2 3.24,0.646 3.781,0.885 0.542,0.24 10 false BAT 3.24,1.208 3.781,1.448 0.542,0.24 10 false IG1 3.24,1.75 3.781,1.99 0.542,0.24 10 false ESS 3.021,1.625 3.563,1.865 0.542,0.24 10 false 1 3.01,1.094 3.552,1.333 0.542,0.24 10 false 4 3.031,0.531 3.573,0.771 0.542,0.24 10 false 5

CAUTION / NOTICE / HINT

NOTICE:
·

Since the panoramic view monitor system has functions that use the CAN communication system, first check that there is no malfunction in the communication system by inspecting the CAN communication functions in accordance with the "How to Proceed with Troubleshooting" procedures. Then, conduct the following inspection procedure.

·

When "!" is displayed on the radio and display receiver assembly after the cable is disconnected from the negative (-) auxiliary battery terminal, correct the steering angle neutral point.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>INITIALIZATION

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>CALIBRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (STEERING SENSOR POWER SOURCE)
a.
E360126C06
1.469,0.385 1.927,0.656 0.458,0.271 1.135,1.875 1.354,1.375 true 1.958,1.865 1.875,1.375 true 2.354,1.781 2.063,1.396 true 1.583,0.438 2.042,0.635 0.458,0.198 10 false F69 0.146,0.167 0.604,0.365 0.458,0.198 10 false *a 0.979,1.896 1.438,2.094 0.458,0.198 10 false ESS 1.865,1.885 2.323,2.083 0.458,0.198 10 false IG1 2.302,1.792 2.76,1.99 0.458,0.198 10 false BAT
*a Front view of wire harness connector
(to Spiral Cable with Sensor Sub-assembly)


Disconnect the steering sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F69-1 (ESS) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F69-4 (IG1) - F69-1 (ESS) Power switch on (IG) 11 to 14 V
F69-5 (BAT) - F69-1 (ESS) Power switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR