Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM › from 2019.09
RM32K0E _56 Audio / Visual / Telematics _060599 PARK ASSIST / MONITORING _0410446 PANORAMIC VIEW MONITOR SYSTEM C

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM  C1686  Driver Side Camera Video Sync Signal Malfunction  


DESCRIPTION

This DTC is stored if the parking assist ECU judges as a result of its self check that a synchronization problem is occurring in the image signal sent from the driver side television camera assembly to the parking assist ECU.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1686 Driver Side Camera Video Sync Signal Malfunction Side camera feedback malfunction
·

Harness or connector

·

Parking assist ECU

·

Side television camera assembly RH

·

Outer rear view mirror assembly with cover RH



WIRING DIAGRAM

E419943E11
0.313,2.594 1.771,3.156 1.458,0.563 10 false Side Television Camera Assembly RH 3.438,0.656 4.354,0.854 0.917,0.198 10 false RCB+ 3.479,1.458 4.396,1.656 0.917,0.198 10 false RCV- 3.438,1.052 4.354,1.25 0.917,0.198 10 false RCV+ 3.417,1.844 4.333,2.042 0.917,0.198 10 false RGND 5.729,0.646 6.646,0.844 0.917,0.198 10 false RCB+ 5.719,1.448 6.635,1.646 0.917,0.198 10 false RCV- 5.729,1.063 6.646,1.26 0.917,0.198 10 false RCV+ 5.729,1.823 6.646,2.021 0.917,0.198 10 false RGND 5.719,2.24 6.635,2.438 0.917,0.198 10 false SGND 4.531,3.24 5.448,3.438 0.917,0.198 10 false *: Shielded 5.521,2.719 6.896,3.323 1.375,0.604 10 false Parking Assist ECU 2.75,2.729 4.271,3.156 1.521,0.427 10 false Outer Rear View Mirror Assembly with Cover RH 2.75,2.563 3.281,2.781 0.531,0.219 10 false I7 5.51,2.563 6.021,2.781 0.51,0.219 10 false M116 4.74,1.979 5.271,2.198 0.531,0.219 10 false * 3.917,0.531 4.448,0.75 0.531,0.219 10 false 5 3.906,0.917 4.438,1.135 0.531,0.219 10 false 6 3.917,1.344 4.448,1.563 0.531,0.219 10 false 13 3.906,1.719 4.438,1.938 0.531,0.219 10 false 14 5.521,0.563 6.052,0.781 0.531,0.219 10 false 6 5.458,0.948 5.99,1.167 0.531,0.219 10 false 30 5.469,1.344 6,1.563 0.531,0.219 10 false 31 5.469,1.719 6,1.938 0.531,0.219 10 false 23 5.469,2.125 6,2.344 0.531,0.219 10 false 32

CAUTION / NOTICE / HINT

NOTICE:
·

When "!" is displayed on the radio and display receiver assembly after the cable is disconnected from the negative (-) auxiliary battery terminal, correct the steering angle neutral point.

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>CALIBRATION



PROCEDURE

1.CHECK FOR DTC
a.

Clear the DTCs.

Chassis > Circumference Monitoring Camera Control Module > Clear DTCs
50002 353

b.

Check for DTCs.

Chassis > Circumference Monitoring Camera Control Module > Trouble Codes
50001 353
OK:

DTC C1686 is not output.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - OUTER REAR VIEW MIRROR ASSEMBLY WITH COVER RH)
2.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - OUTER REAR VIEW MIRROR ASSEMBLY WITH COVER RH)
a.

Disconnect the M116 parking assist ECU connector.


b.

Disconnect the I7 outer rear view mirror assembly with cover RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M116-6 (RCB+) - I7-5 (RCB+) Always Below 1 Ω
M116-30 (RCV+) - I7-6 (RCV+) Always Below 1 Ω
M116-31 (RCV-) - I7-13 (RCV-) Always Below 1 Ω
M116-23 (RGND) - I7-14 (RGND) Always Below 1 Ω
M116-32 (SGND) - Body ground Always Below 1 Ω
M116-6 (RCB+) or I7-5 (RCB+) - Body ground Always 10 kΩ or higher
M116-30 (RCV+) or I7-6 (RCV+) - Body ground Always 10 kΩ or higher
M116-31 (RCV-) or I7-13 (RCV-) - Body ground Always 10 kΩ or higher
M116-23 (RGND) or I7-14 (RGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK PARKING ASSIST ECU (RCV-, RGND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK PARKING ASSIST ECU (RCV-, RGND)
a.

Disconnect the M116 parking assist ECU connector.


b.
E430023C01
1.479,0.219 1.875,0.458 0.396,0.24 1.99,1.156 2.271,1.677 true 1.146,1.656 1.552,1.146 true 1.51,0.24 1.885,0.396 0.375,0.156 10 false M116 0.115,0.063 0.313,0.24 0.198,0.177 10 false *a 2.271,1.729 2.688,1.885 0.417,0.156 10 false RGND 0.885,1.708 1.302,1.865 0.417,0.156 10 false RCV-
*a Component without harness connected
(Parking Assist ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M116-23 (RGND) - Body ground Always Below 1 Ω
M116-31 (RCV-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK PARKING ASSIST ECU (RCB+, RGND)

NG

4.CHECK PARKING ASSIST ECU (RCB+, RGND)
a.
E403271C59
1.688,0.698 2.115,0.917 0.427,0.219 2.573,0.854 2.427,1.469 true 2.625,2.417 2.438,1.646 true 0.167,0.156 0.385,0.333 0.219,0.177 10 false *a 2.531,2.49 2.958,2.656 0.427,0.167 10 false RGND 2.531,0.635 2.948,0.802 0.417,0.167 10 false RCB+ 1.729,0.708 2.104,0.875 0.375,0.167 10 false M116
*a Component with harness connected
(Parking Assist ECU)


Remove the parking assist ECU with the connector still connected.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M116-23 (RGND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
M116-6 (RCB+) - M116-23 (RGND) Power switch on (IG) 5.5 to 7.05 V



Result:
Proceed to
OK
NG



OK

5.CHECK SIDE TELEVISION CAMERA ASSEMBLY RH (RCV+, RGND)

NG

5.CHECK SIDE TELEVISION CAMERA ASSEMBLY RH (RCV+, RGND)
a.

Remove the parking assist ECU with the connector still connected.


b.
E403271C60
1.688,0.698 2.115,0.917 0.427,0.219 2.427,1.656 2.698,2.417 true 1.875,1.646 1.479,2.417 true 0.167,0.156 0.385,0.333 0.219,0.177 10 false *a 2.51,2.458 3.021,2.688 0.51,0.229 10 false RGND 1.281,2.469 1.698,2.635 0.417,0.167 10 false RCV+ 1.719,0.719 2.094,0.885 0.375,0.167 10 false M116
*a Component with harness connected
(Parking Assist ECU)


Using an oscilloscope, check the waveform of the side television camera assembly RH.

HINT:

A waterproof connector is used for the side television camera assembly RH. Therefore, inspect the waveform at the parking assist ECU with the connector connected.


HINT:
E265840C28
0.854,1.99 1.115,1.583 true 1.458,1.979 1.24,1.469 true 1.51,4.125 1.281,3.542 true 0.854,4.146 1.146,3.604 true 0.229,0.229 0.542,0.427 0.313,0.198 10 false *a 0.396,1.052 0.76,1.313 0.365,0.26 10 false GND 0.396,3.208 0.76,3.469 0.365,0.26 10 false GND 0.26,2.271 0.625,2.531 0.365,0.26 10 false *b 0.646,4.073 1.01,4.333 0.365,0.26 10 false *c 0.677,1.958 1.042,2.219 0.365,0.26 10 false *c 1.458,1.969 1.823,2.229 0.365,0.26 10 false *d 1.479,4.115 1.844,4.375 0.365,0.26 10 false *d
*a Waveform 1 (camera lens not covered, displaying an image)
*b Waveform 2 (camera lens covered, blacking out the screen)
*c Synchronization Signal
*d Video Waveform


·

The video waveform changes according to the image sent by the side television camera assembly RH.

·

The video waveform is constantly output when the power switch is on (ACC).



Measurement Condition
Item Content
Tester Connection M116-30 (RCV+) - M116-23 (RGND)
Tool Setting 200 mV/DIV., 50 μs./DIV.
Condition Power switch on (IG), panoramic view monitor system operating

OK:

Waveform is similar to that shown in illustration.



Result:
Proceed to
OK
NG



OK

NG

6.REPLACE SIDE TELEVISION CAMERA ASSEMBLY RH
6.REPLACE SIDE TELEVISION CAMERA ASSEMBLY RH
a.

Replace the side television camera assembly RH with a new or known good one.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA (for Side)>REMOVAL


Result:
Proceed to
NEXT



NEXT

7.CHECK FOR DTC
7.CHECK FOR DTC
a.

Clear the DTCs.

Chassis > Circumference Monitoring Camera Control Module > Clear DTCs
50002 353

b.

Check for DTCs.

Chassis > Circumference Monitoring Camera Control Module > Trouble Codes
50001 353
OK:

DTC C1683 is not output.



Result:
Proceed to
OK
NG



OK

END (SIDE TELEVISION CAMERA ASSEMBLY RH IS DEFECTIVE)

NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY WITH COVER RH