Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM › from 2019.09
RM32K0E _56 Audio / Visual / Telematics _060599 PARK ASSIST / MONITORING _0410446 PANORAMIC VIEW MONITOR SYSTEM J

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM  ECU Power Source Circuit  


DESCRIPTION

This circuit is the power source circuit to operate the parking assist ECU. The parking assist ECU controls the panoramic view monitor system.

WIRING DIAGRAM

E403285E10
0.26,1 1.729,1.25 1.469,0.25 10 false from Auxiliary Battery 0.302,2.104 2.292,2.302 1.99,0.198 10 false from IG1-NO. 1 Relay 0.625,2.677 2.615,2.875 1.99,0.198 10 false from ACC Relay 2.115,1.177 3.042,1.458 0.927,0.281 10 false ECU-B NO. 2 2.042,2.271 3.125,2.521 1.083,0.25 10 false ECU-IG1 NO. 4 2.198,2.844 3.729,3.042 1.531,0.198 10 false ECU-ACC 5.313,0.948 5.469,1.146 0.156,0.198 10 false 1 5.271,1.99 5.552,2.188 0.281,0.198 10 false 21 5.333,2.583 5.615,2.781 0.281,0.198 10 false 3 5.333,3.063 5.615,3.26 0.281,0.198 10 false 2 5.552,1.052 5.865,1.25 0.313,0.198 10 false +B 5.573,2.156 5.885,2.354 0.313,0.198 10 false IG 5.552,2.677 6.01,2.875 0.458,0.198 10 false ACC 5.542,3.198 6.156,3.396 0.615,0.198 10 false GND1 5.271,3.844 5.833,4.021 0.563,0.177 10 false M116 5.271,4.031 6.708,4.271 1.438,0.24 10 false Parking Assist ECU 5.552,1.573 5.865,1.771 0.313,0.198 10 false +B2 5.26,1.479 5.604,1.719 0.344,0.24 10 false 19 5.563,3.531 6.177,3.729 0.615,0.198 10 false GND2 5.26,3.438 5.583,3.677 0.323,0.24 10 false 20

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuse for circuits related to this system before performing the following inspection procedure.


HINT:

If the parking assist ECU does not operate due to a power source problem, other system DTCs may be stored due to a CAN communication interruption.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - BODY GROUND)
a.

Disconnect the M116 parking assist ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M116-2 (GND1) - Body ground Always Below 1 Ω
M116-20 (GND2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU POWER SOURCE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU POWER SOURCE)
a.

Disconnect the M116 parking assist ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
M116-1 (+B) - M116-2 (GND1) Power switch off 11 to 14 V
M116-19 (+B2) - M116-2 (GND1) Power switch off 11 to 14 V
M116-3 (ACC) - M116-2 (GND1) Power switch on (ACC) 11 to 14 V
Power switch off Below 1 V
M116-21 (IG) - M116-2 (GND1) Power switch on (IG) 11 to 14 V
Power switch off Below 1 V



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR