Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM › from 2019.09
RM32K0E _58 Vehicle Interior _061197 THEFT DETERRENT / KEYLESS ENTRY _0299417 IMMOBILISER SYSTEM U

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM  TERMINALS OF ECU  


CHECK POWER SWITCH


B271001E32
3.354,0.229 3.729,0.458 0.375,0.229 3.427,0.25 3.74,0.427 0.313,0.177 10 false F59

a.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
F59-6 (AGND) - Body ground - P - Body ground Transponder key amplifier ground Always Below 1 Ω -
F59-7 (TXCT) - F59-6 (AGND) Input B - P Immobiliser communication input Power switch off, brake pedal not depressed, 30 seconds or more after driver door opened and then closed Below 1 V -
F59-8 (CODE) - F59-6 (AGND) Output L - P Immobiliser communication output Power switch off, brake pedal not depressed, 30 seconds or more after driver door opened and then closed Below 1 V -
F59-10 (VC5) - F59-6 (AGND) Input Y - P Transponder key amplifier power supply Power switch off, brake pedal not depressed, 30 seconds or more after driver door opened and then closed Below 1 V -


b.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
F59-7 (TXCT) - F59-6 (AGND) Input B - P Signal input from certification ECU (smart key ECU assembly)
(Code sent from certification ECU (smart key ECU assembly) to transponder key amplifier built into power switch, and then transmitted by transponder key amplifier antenna as radio waves)
Power switch off, electrical key transmitter sub-assembly not in cabin, within 30 seconds after power switch pressed Pulse generation
(See waveform 1)
·

BCC Malfunction

·

Abnormal Status

·

Different Encrypt Code

·

Different Serial Number

·

Frame Error

·

Response

HINT:

If immobiliser key code verification communication is not performed correctly, the malfunction may be indicated by one or more of the Data List items listed above



F59-8 (CODE) - F59-6 (AGND) Output L - P Signal output to certification ECU (smart key ECU assembly)
(Radio waves from transponder key amplifier built into power switch used to detect key information. Key information then sent to certification ECU (smart key ECU assembly))
Power switch off, power switch pressed with electrical key transmitter sub-assembly held near power switch* Pulse generation
(See waveform 2)
F59-10 (VC5) - F59-6 (AGND) Input Y - P Transponder key amplifier power supply
(Power supplied from certification ECU (smart key ECU assembly) when transponder key amplifier built into power switch activated)
Power switch off, electrical key transmitter sub-assembly not in cabin, within 30 seconds after power switch pressed Pulse generation
(See waveform 3)

HINT:

*: Remove the transmitter battery before performing this inspection.



c.

Using an oscilloscope, check the waveform.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.
B051052N18
2.802,0.781 3.156,0.969 0.354,0.188 10 GND

Waveform 1 (Reference)

Measurement Condition
Item Content
Tester Connection F59-7 (TXCT) - F59-6 (AGND)
Tool Setting 2 V/DIV., 20 ms./DIV.
Condition Power switch off, electrical key transmitter sub-assembly not in cabin, within 30 seconds after power switch pressed


ii.
B368716C01
0.104,0.135 0.417,0.292 0.313,0.156 10 false *a 0.094,1.896 0.406,2.052 0.313,0.156 10 false *b 3.031,1.219 3.427,1.49 0.396,0.271 10 false GND 3.031,2.948 3.427,3.219 0.396,0.271 10 false GND
*a Waveform
*b Waveform (detail)


Waveform 2 (Reference)

Measurement Condition
Item Content
Tester Connection F59-8 (CODE) - F59-6 (AGND)
Tool Setting
·

Waveform

1 V/DIV., 20 ms./DIV.

·

Waveform (detail)

2 V/DIV., 100 μs./DIV.


Condition Power switch off, power switch pressed with electrical key transmitter sub-assembly held near power switch*

HINT:

*: Remove the transmitter battery before performing this inspection.



iii.
B216007N05
2.885,1.031 3.427,1.375 0.542,0.344 10 GND

Waveform 3 (Reference)

Measurement Condition
Item Content
Tester Connection F59-10 (VC5) - F59-6 (AGND)
Tool Setting 2 V/DIV., 200 ms./DIV.
Condition Power switch off, electrical key transmitter sub-assembly not in cabin, within 30 seconds after power switch pressed




CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


B427558E04
3.25,0.542 3.656,0.781 0.406,0.24 4.531,0.542 4.938,0.781 0.406,0.24 3.323,0.573 3.635,0.771 0.313,0.198 10 false M67 4.625,0.583 4.938,0.781 0.313,0.198 10 false F1

a.

Disconnect the F1 certification ECU (smart key ECU assembly) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
F1-4 (+B) - F1-18 (E) Input L - W-B +B power supply Power switch off 11 to 14 V -
F1-18 (E) - Body ground - W-B - Body ground Ground Always Below 1 Ω -


c.

Reconnect the F1 certification ECU (smart key ECU assembly) connector.


d.

Measure the voltage and resistance, and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
F1-17 (IG1D) - F1-18 (E) Output GR - W-B Ignition power supply Power switch off Below 1 V -
Power switch on (IG) 11 to 14 V -
F1-5 (TXCT) - F1-11 (AGND) Output B - P Signal output to transponder key amplifier Power switch off, brake pedal not depressed, 30 seconds or more after driver door opened and then closed Below 1 V
·

BCC Malfunction

·

Abnormal Status

·

Different Encrypt Code

·

Different Serial Number

·

Frame Error

·

Response


F1-6 (CODE) - F1-11 (AGND) Input L - P Signal input from transponder key amplifier Power switch off, brake pedal not depressed, 30 seconds or more after driver door opened and then closed Below 1 V
F1-7 (VC5) - F1-11 (AGND) Output Y - P Transponder key amplifier power supply Power switch off, brake pedal not depressed, 30 seconds or more after driver door opened and then closed Below 1 V
F1-11 (AGND) - Body ground - P - Body ground Transponder key amplifier ground Always Below 1 Ω
F1-20 (IND) - F1-18 (E) Output P - W-B Security indicator output Power switch off → on (IG) Pulse generation → Below 2 V -


e.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
F1-5 (TXCT) - F1-11 (AGND) Output B - P Signal output to transponder key amplifier
(Code sent from certification ECU (smart key ECU assembly) to transponder key amplifier built into power switch, and then transmitted by transponder key amplifier antenna as radio waves)
Power switch off, electrical key transmitter sub-assembly not in cabin, within 30 seconds of power switch pressed Pulse generation
(See waveform 1)
·

BCC Malfunction

·

Abnormal Status

·

Different Encrypt Code

·

Different Serial Number

·

Frame Error

·

Response


F1-6 (CODE) - F1-11 (AGND) Input L - P Signal input from transponder key amplifier
(Radio waves from transponder key amplifier built into power switch used to detect key information. Key information then sent to certification ECU (smart key ECU assembly))
Power switch off, power switch pressed with electrical key transmitter sub-assembly held near power switch
HINT:

Remove the transmitter battery before performing this inspection.


Pulse generation
(See waveform 2)
F1-7 (VC5) - F1-11 (AGND) Output Y - P Transponder key amplifier power supply
(Power supplied from certification ECU (smart key ECU assembly) when transponder key amplifier built into power switch activated)
Power switch off, electrical key transmitter sub-assembly not in cabin, within 30 seconds of power switch pressed Pulse generation
(See waveform 3)


f.

Using an oscilloscope, check the waveform.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.
B051052N19
2.802,0.781 3.156,0.969 0.354,0.188 10 GND

Waveform 1 (Reference)

Measurement Condition
Item Content
Tester Connection F1-5 (TXCT) - F1-11 (AGND)
Tool Setting 2 V/DIV., 20 ms./DIV.
Condition Power switch off, electrical key transmitter sub-assembly not in cabin, within 30 seconds of power switch pressed


ii.
B368716C01
0.104,0.135 0.417,0.292 0.313,0.156 10 false *a 0.094,1.896 0.406,2.052 0.313,0.156 10 false *b 3.031,1.219 3.427,1.49 0.396,0.271 10 false GND 3.031,2.948 3.427,3.219 0.396,0.271 10 false GND
*a Waveform
*b Waveform (detail)


Waveform 2 (Reference)

Measurement Condition
Item Content
Tester Connection F1-6 (CODE) - F1-11 (AGND)
Tool Setting
·

Waveform

1 V/DIV., 20 ms./DIV.

·

Waveform (detail)

2 V/DIV., 100 μs./DIV.


Condition Power switch off, power switch pressed with electrical key transmitter sub-assembly held near power switch*

HINT:

*: Remove the transmitter battery before performing this inspection.



iii.
B216007N06
2.885,1.031 3.427,1.375 0.542,0.344 10 GND

Waveform 3 (Reference)

Measurement Condition
Item Content
Tester Connection F1-7 (VC5) - F1-11 (AGND)
Tool Setting 2 V/DIV., 200 ms./DIV.
Condition Power switch off, electrical key transmitter sub-assembly not in cabin, within 30 seconds of power switch pressed




CHECK ID CODE BOX (IMMOBILISER CODE ECU)


B278917E32
3.396,0.156 3.792,0.385 0.396,0.229 3.469,0.177 3.792,0.354 0.323,0.177 10 false F21

a.

Disconnect the F21 ID code box (immobiliser code ECU) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
F21-1 (+B) - Body ground Input W - Body ground +B power supply Power switch off 11 to 14 V B2789
F21-5 (GND) - Body ground - W-B - Body ground Ground Always Below 1 Ω B2789


c.

Reconnect the F21 ID code box (immobiliser code ECU) connector.


d.

Measure the voltage and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
F21-3 (EFII) - F21-5 (GND) Input V - W-B EFI communication input
(Signal input from hybrid vehicle control ECU assembly to ID code box (immobiliser code ECU))
Power switch off 11 to 14 V
·

B279986

·

B279A12

·

EFI Code Receive

·

Engine Start Request


F21-4 (EFIO) - F21-5 (GND) Output R - W-B EFI communication output
(Signal output from ID code box (immobiliser code ECU) to hybrid vehicle control ECU assembly)
Power switch off 11 to 14 V → Below 1 V
F21-3 (EFII) - F21-5 (GND) Input V - W-B EFI communication input
(Signal input from hybrid vehicle control ECU assembly to ID code box (immobiliser code ECU))
Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after cable disconnected and reconnected to auxiliary battery Pulse generation
(See waveform 1)
F21-4 (EFIO) - F21-5 (GND) Output R - W-B EFI communication output
(Signal output from ID code box (immobiliser code ECU) to hybrid vehicle control ECU assembly)
Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after cable disconnected and reconnected to auxiliary battery Pulse generation
(See waveform 2)


e.

Using an oscilloscope, check the waveform.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.

Waveform 1 (Reference)

B325134C03
0.917,1.271 1.375,1.469 0.458,0.198 10 GND 2.719,1.354 3.177,1.552 0.458,0.198 10 *a 2.906,1.354 3.365,1.552 0.458,0.198 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Measurement Condition
Item Content
Tester Connection F21-3 (EFII) - F21-5 (GND)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after cable disconnected and reconnected to auxiliary battery


ii.

Waveform 2 (Reference)

B333259C02
0.844,1.24 1.302,1.438 0.458,0.198 10 GND 3.115,1.323 3.344,1.531 0.229,0.208 10 *a 3.313,1.323 3.542,1.531 0.229,0.208 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Measurement Condition
Item Content
Tester Connection F21-4 (EFIO) - F21-5 (GND)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after cable disconnected and reconnected to auxiliary battery




CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)


E360536E01
3.417,0.333 3.865,0.583 0.448,0.25 3.521,0.375 3.979,0.573 0.458,0.198 10 false F78

a.

Measure the voltage and resistance and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
F78-1 (GND) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
F78-3 (IGE) - F78-1 (GND) Input P - W-B Steering lock motor operation permission signal (motor operation permission signal supplied by certification ECU (smart key ECU assembly)) Steering lock motor operates when both conditions met, and then door opened:
·

Shift lever in P

·

Steering unlocked

·

Power switch turned off


Pulse generation
(See waveform 1)
·

Power Supply Short

·

Unlock Request Receive

·

Lock Request Receive


F78-4 (SLP1) - F78-1 (GND) Output G - W-B Steering lock bar position signal (signal output from steering unlock sensor) Steering locked → unlocked* 11 to 14 V → Below 1.5 V Sensor Value
F78-6 (IG2) - F78-1 (GND) Input SB - W-B*1
B - W-B*2
IG signal (IG2 power supply input for steering lock motor) Power switch off → on (IG) Below 1 V → 11 to 14 V B2788
F78-7 (B) - Body ground Input L - Body ground Constant power supply Power switch off 11 to 14 V B2788

HINT:

*: The steering locks when any door is opened with the shift lever in P and the power switch off. The steering unlocks when the power switch is turned on (ACC).


*1: for TMC Made

*2: except TMC Made



b.

Using an oscilloscope, check the waveform.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.
C259594C03
1.052,0.344 2.958,0.219 2.958,0.219 2.521,0.396 true 2.031,1.802 2.292,1.969 true 3.01,0.135 3.323,0.292 0.313,0.156 10 *a 2.344,1.938 2.667,2.104 0.323,0.167 10 *b 2.938,1.594 3.302,1.792 0.365,0.198 10 GND
*a Steering lock motor not operating
*b Steering lock motor operating


Waveform 1 (Reference)

Measurement Condition
Item Content
Tester Connection F78-3 (IGE) -F78-1 (GND)
Tool Setting 2 V/DIV., 200 ms./DIV.
Condition Steering lock motor operates when both conditions met, and then door opened:
·

Shift lever in P

·

Steering unlocked

·

Power switch turned off






CHECK HYBRID VEHICLE CONTROL ECU ASSEMBLY (for 2ZR-FXE)


B220221E14
1.479,0.135 1.865,0.365 0.385,0.229 2.833,0.146 3.219,0.375 0.385,0.229 4.302,0.146 4.688,0.375 0.385,0.229 5.531,0.167 5.917,0.396 0.385,0.229 1.552,0.167 2.198,0.521 0.646,0.354 10 false A49 2.906,0.177 3.375,0.469 0.469,0.292 10 false A48 4.427,0.177 4.906,0.438 0.479,0.26 10 false F2 5.646,0.198 6.115,0.417 0.469,0.219 10 false F3

a.

Measure the voltage and resistance and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
A49-1 (+B2) - F2-6 (E1) Input L - W-B Ignition power supply Power switch on (IG) 11 to 14 V -
A48-4 (+B1) - F2-6 (E1) Input L - W-B Ignition power supply Power switch on (IG) 11 to 14 V -
A48-6 (MREL) - F2-6 (E1) Output BE - W-B Ignition power supply Power switch on (IG) 11 to 14 V -
F2-5 (E01) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
F2-6 (E1) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
F3-4 (E12) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
F3-5 (E02) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
F3-3 (BATT) - F2-6 (E1) Input B - W-B +B power supply Power switch off 11 to 14 V -
F3-23 (IMO) - F2-6 (E1) Output V - W-B ID code box (immobiliser code ECU) communication output Power switch off 11 to 14 V -
F3-23 (IMO) - F2-6 (E1) Output V - W-B ID code box (immobiliser code ECU) communication output Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after cable disconnected and reconnected to auxiliary battery Pulse generation
(See waveform 1)
-
F3-22 (IMI) - F2-6 (E1) Input R - W-B ID code box (immobiliser code ECU) communication input Power switch off 11 to 14 V → Below 1 V -
F3-22 (IMI) - F2-6 (E1) Input R - W-B ID code box (immobiliser code ECU) communication input Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after cable disconnected and reconnected to auxiliary battery Pulse generation
(See waveform 2)
-


b.

Using an oscilloscope, check the waveform.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.

Waveform 1 (Reference)

B325134C03
0.917,1.271 1.375,1.469 0.458,0.198 10 GND 2.719,1.354 3.177,1.552 0.458,0.198 10 *a 2.906,1.354 3.365,1.552 0.458,0.198 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Measurement Condition
Item Content
Tester Connection F3-23 (IMO) - F2-6 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after cable disconnected and reconnected to auxiliary battery


ii.

Waveform 2 (Reference)

B333259C02
0.844,1.24 1.302,1.438 0.458,0.198 10 GND 3.115,1.323 3.344,1.531 0.229,0.208 10 *a 3.313,1.323 3.542,1.531 0.229,0.208 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Measurement Condition
Item Content
Tester Connection F3-22 (IMI) - F2-6 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after cable disconnected and reconnected to auxiliary battery




CHECK HYBRID VEHICLE CONTROL ECU ASSEMBLY (for M20A-FXS)


C338835E23
1.25,0.323 1.667,0.583 0.417,0.26 3.271,0.292 3.688,0.552 0.417,0.26 5.313,0.302 5.729,0.563 0.417,0.26 1.354,0.375 1.813,0.573 0.458,0.198 10 false A97 3.333,0.354 3.792,0.552 0.458,0.198 10 false F160 5.375,0.354 5.833,0.552 0.458,0.198 10 false F161

a.

Measure the voltage and resistance and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
F161-1 (+B2) - F161-3 (E1) Input B - W-B Ignition power supply Power switch on (IG) 11 to 14 V -
A97-11 (+B1) - F161-3 (E1) Input R - W-B Ignition power supply Power switch on (IG) 11 to 14 V -
A97-5 (MREL) - F161-3 (E1) Output BE - W-B Ignition power supply Power switch on (IG) 11 to 14 V -
F160-12 (E01) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
F161-3 (E1) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
F160-34 (E12) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
F160-11 (E02) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
F161-27 (BATT) - F161-3 (E1) Input B - W-B*1
Y - W-B*2
+B power supply Power switch off 11 to 14 V -
F161-23 (IMO) - F161-3 (E1) Output V - W-B ID code box (immobiliser code ECU) communication output Power switch off 11 to 14 V -
Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after cable disconnected and reconnected to auxiliary battery Pulse generation
(See waveform 1)
F161-10 (IMI) - F161-3 (E1) Input R - W-B ID code box (immobiliser code ECU) communication input Power switch off 11 to 14 V → Below 1 V -
Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after cable disconnected and reconnected to auxiliary battery Pulse generation
(See waveform 2)

*1: for RHD

*2: for LHD



b.

Using an oscilloscope, check the waveform.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.

Waveform 1 (Reference)

B325134C03
0.917,1.271 1.375,1.469 0.458,0.198 10 GND 2.719,1.354 3.177,1.552 0.458,0.198 10 *a 2.906,1.354 3.365,1.552 0.458,0.198 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Measurement Condition
Item Content
Tester Connection F161-23 (IMO) - F161-3 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after cable disconnected and reconnected to auxiliary battery


ii.

Waveform 2 (Reference)

B333259C02
0.844,1.24 1.302,1.438 0.458,0.198 10 GND 3.115,1.323 3.344,1.531 0.229,0.208 10 *a 3.313,1.323 3.542,1.531 0.229,0.208 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Measurement Condition
Item Content
Tester Connection F161-10 (IMI) - F161-3 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after cable disconnected and reconnected to auxiliary battery