Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio Receiver Type) › from 2019.09
RM32K0E _56 Audio / Visual / Telematics _061817 AUDIO / VIDEO _0301273 AUDIO AND VISUAL SYSTEM(for Radio Receiver Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio Receiver Type)  Microphone Circuit between Microphone and Radio Receiver  


DESCRIPTION

The radio receiver assembly and map light assembly (telephone microphone assembly) are connected to each other using the microphone connection detection signal lines.

Using this circuit, the radio receiver assembly sends power to the map light assembly (telephone microphone assembly), and the map light assembly (telephone microphone assembly) sends microphone signals to the radio receiver assembly.

WIRING DIAGRAM

E361269E01
5.74,2.792 6.198,2.99 0.458,0.198 10 false F47 5.885,0.438 6.344,0.635 0.458,0.198 10 false MACC 5.875,0.917 6.333,1.115 0.458,0.198 10 false MIN+ 5.875,1.396 6.333,1.594 0.458,0.198 10 false MIN- 5.865,1.875 6.323,2.073 0.458,0.198 10 false SGND 5.885,2.344 6.344,2.542 0.458,0.198 10 false SNS2 3.156,1.719 3.938,1.927 0.781,0.208 10 false (Shielded) 0.75,0.438 1.208,0.635 0.458,0.198 10 false MACC 0.792,2.344 1.25,2.542 0.458,0.198 10 false SNS2 0.74,0.885 1.198,1.083 0.458,0.198 10 false MCO+ 0.76,1.385 1.219,1.583 0.458,0.198 10 false MCO- 0.365,2.802 0.823,3 0.458,0.198 10 false R2 0.354,3 2.344,3.677 1.99,0.677 10 false Map Light Assembly (Telephone Microphone Assembly) 5.75,2.99 6.708,3.708 0.958,0.719 10 false Radio Receiver Assembly 1.24,0.302 1.667,0.49 0.427,0.188 10 false 9 1.24,0.771 1.667,0.958 0.427,0.188 10 false 8 1.24,1.25 1.667,1.438 0.427,0.188 10 false 7 1.24,2.198 1.667,2.385 0.427,0.188 10 false 1 5.677,0.323 6.104,0.51 0.427,0.188 10 false 4 5.688,0.781 6.115,0.969 0.427,0.188 10 false 5 5.615,1.24 7.021,1.406 1.406,0.167 10 false 19 5.625,1.719 6.729,1.885 1.104,0.167 10 false 18 5.667,2.198 6.094,2.385 0.427,0.188 10 false 6

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))
a.

Disconnect the F47 radio receiver assembly connector.


b.

Disconnect the R2 map light assembly (telephone microphone assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F47-6 (SNS2) - R2-1 (SNS2) Always Below 1 Ω
F47-4 (MACC) - R2-9 (MACC) Always Below 1 Ω
F47-5 (MIN+) - R2-8 (MCO+) Always Below 1 Ω
F47-19 (MIN-) - R2-7 (MCO-) Always Below 1 Ω
F47-6 (SNS2) or R2-1 (SNS2) - Body ground Always 10 kΩ or higher
F47-4 (MACC) or R2-9 (MACC) - Body ground Always 10 kΩ or higher
F47-5 (MIN+) or R2-8 (MCO+) - Body ground Always 10 kΩ or higher
F47-19 (MIN-) or R2-7 (MCO-) - Body ground Always 10 kΩ or higher
F47-18 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.INSPECT RADIO RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT RADIO RECEIVER ASSEMBLY
a.

Connect the F47 radio receiver assembly connector.


b.

Connect the R2 map light assembly (telephone microphone assembly) connector.


c.
E359760C01
1.427,0.625 1.896,0.917 0.469,0.292 1.115,2.635 2.052,1.99 true 2.24,1.75 2.917,1.344 true 2.219,2 2.635,2.563 true 0.167,0.125 0.479,0.323 0.313,0.198 10 false *a 1.542,0.688 1.854,0.885 0.313,0.198 10 false F47 2.938,1.167 3.427,1.479 0.49,0.313 10 false MACC 2.594,2.625 3.052,2.875 0.458,0.25 10 false SGND 0.865,2.625 1.25,2.844 0.385,0.219 10 false MIN-
*a Component with harness connected
(Radio Receiver Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F47-4 (MACC) - Body ground power switch on (ACC). 4 to 6 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F47-18 (SGND) - Body ground Always Below 1 Ω
F47-19 (MIN-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

NG

3.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)
a.

Remove the map light assembly (telephone microphone assembly).

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT (for TMMT Made)>REMOVAL


b.
E358190C01
2.281,1.094 2.552,0.49 true 2.292,1.427 2.583,1.771 true 0.25,0.198 0.563,0.396 0.313,0.198 10 false *a 2.479,0.302 2.948,0.521 0.469,0.219 10 false SNS2 2.583,1.771 2.979,1.979 0.396,0.208 10 false MCO-
*a Component without harness connected
(Map Light Assembly (Telephone Microphone Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (SNS2) - 7 (MCO-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

NG

REPLACE MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

4.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)
a.

Connect the R2 map light assembly (telephone microphone assembly) connector.


b.

Turn the power switch on (ACC).


c.
E358189C01
1.542,0.49 1.969,0.75 0.427,0.26 2.188,1.75 2.708,2.177 true 1.99,1.781 2.208,2.385 true 0.219,0.177 0.531,0.375 0.313,0.198 10 false *a 1.646,0.521 1.958,0.719 0.313,0.198 10 false R2 2.76,2.188 3.198,2.458 0.438,0.271 10 false MCO- 2.115,2.427 2.604,2.698 0.49,0.271 10 false MCO+
*a Component with harness connected
(Map Light Assembly (Telephone Microphone Assembly))


Connect an oscilloscope to terminals 8 (MCO+) and 7 (MCO-) of the R2 map light assembly (telephone microphone assembly) connector.


d.

Check the waveform of the map light assembly (telephone microphone assembly) using the oscilloscope.

Result:
Result Proceed to
A waveform synchronized with the voice input to the map light assembly (telephone microphone assembly) is output. A
A waveform synchronized with the voice input to the map light assembly (telephone microphone assembly) is not output. B




A

B

REPLACE MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)