Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM (w/ Headlight ECU) › from 2019.09
RM32K0E _59 Vehicle Exterior _061162 LIGHTING (EXT) _0408676 LIGHTING SYSTEM(w/ Headlight ECU) U

LIGHTING (EXT)  LIGHTING SYSTEM(w/ Headlight ECU)  TERMINALS OF ECU  


CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


B434105C68
2.146,3.104 2.542,3.344 0.396,0.24 4.604,3.083 5,3.323 0.396,0.24 1.396,4.573 1.792,4.813 0.396,0.24 3.729,4.583 4.125,4.823 0.396,0.24 5.292,4.615 5.688,4.854 0.396,0.24 6.292,4.625 6.688,4.865 0.396,0.24 4.646,6.229 5.042,6.469 0.396,0.24 1.51,6.208 1.906,6.448 0.396,0.24 3.417,7.844 3.813,8.083 0.396,0.24 1.667,1.479 1.906,1.479 true 1.667,1.802 1.906,1.802 true 1.438,2.792 1.438,1.469 1.438,1.469 1.552,1.469 true 1.438,1.802 1.552,1.802 true 4.031,0.792 4.156,0.219 true 1.594,0.646 1.719,0.24 true 1.969,1.406 2.281,1.604 0.313,0.198 10 false F15 4.219,0.135 4.531,0.333 0.313,0.198 10 false MB 0.875,1.115 1.188,1.313 0.313,0.198 10 false 3H 0.885,1.656 1.198,1.854 0.313,0.198 10 false 3F 0.885,2.031 1.198,2.229 0.313,0.198 10 false 3L 0.896,2.25 1.208,2.448 0.313,0.198 10 false 3K 1.969,1.708 2.281,1.906 0.313,0.198 10 false F16 5.854,1.135 6.167,1.333 0.313,0.198 10 false 3D 5.854,1.781 6.167,1.979 0.313,0.198 10 false 3A 4.698,3.125 5.01,3.323 0.313,0.198 10 false F15 2.219,3.146 2.531,3.344 0.313,0.198 10 false F16 1.521,4.615 1.833,4.813 0.313,0.198 10 false 3H 3.865,4.625 4.177,4.823 0.313,0.198 10 false 3F 5.417,4.667 5.729,4.865 0.313,0.198 10 false 3L 6.406,4.677 6.719,4.875 0.313,0.198 10 false 3K 1.625,6.26 1.938,6.458 0.313,0.198 10 false 3D 4.771,6.281 5.083,6.479 0.313,0.198 10 false 3A 3.531,7.896 3.844,8.094 0.313,0.198 10 false MB 0.125,0.135 0.615,0.375 0.49,0.24 12 false *A 1.771,0.125 2.677,0.323 0.906,0.198 10 false *1 1.365,2.833 2.271,3.031 0.906,0.198 10 false *a
*A Main Body ECU (Multiplex Network Body ECU) with 2 Connectors - -
*1 Main Body ECU (Multiplex Network Body ECU) - -
*a 2 Connectors - -


B434104C56
3.531,3.198 3.896,3.417 0.365,0.219 1.396,4.583 1.76,4.802 0.365,0.219 3.729,4.583 4.094,4.802 0.365,0.219 5.313,4.583 5.677,4.802 0.365,0.219 6.302,4.552 6.667,4.771 0.365,0.219 1.583,6.24 1.948,6.458 0.365,0.219 4.813,6.26 5.177,6.479 0.365,0.219 3.354,7.854 3.719,8.073 0.365,0.219 1.667,1.333 1.906,1.333 true 1.417,2.708 1.417,1.333 1.417,1.333 1.542,1.333 true 1.615,0.646 1.74,0.208 true 3.99,0.802 4.146,0.24 true 0.865,1.094 1.177,1.292 0.313,0.198 10 false 3H 0.865,1.646 1.177,1.844 0.313,0.198 10 false 3F 0.875,2.01 1.188,2.208 0.313,0.198 10 false 3L 0.885,2.24 1.198,2.438 0.313,0.198 10 false 3K 1.969,1.26 2.281,1.458 0.313,0.198 10 false F15 4.188,0.125 4.5,0.323 0.313,0.198 10 false MB 5.844,1.104 6.156,1.302 0.313,0.198 10 false 3D 5.844,1.76 6.156,1.958 0.313,0.198 10 false 3A 3.604,3.219 3.917,3.417 0.313,0.198 10 false F15 1.5,4.604 1.813,4.802 0.313,0.198 10 false 3H 3.823,4.604 4.135,4.802 0.313,0.198 10 false 3F 5.427,4.604 5.74,4.802 0.313,0.198 10 false 3L 6.396,4.583 6.708,4.781 0.313,0.198 10 false 3K 1.688,6.26 2,6.458 0.313,0.198 10 false 3D 4.917,6.292 5.229,6.49 0.313,0.198 10 false 3A 3.438,7.875 3.75,8.073 0.313,0.198 10 false MB 0.167,0.115 0.531,0.396 0.365,0.281 12 false *A 1.813,0.115 3,0.49 1.188,0.375 10 false *1 1.344,2.75 2.531,3.125 1.188,0.375 10 false *a
*A Main Body ECU (Multiplex Network Body ECU) with 1 Connector - -
*1 Main Body ECU (Multiplex Network Body ECU) - -
*a 1 Connector - -


a.

Disconnect the instrument panel junction block assembly and main body ECU (multiplex network body ECU) connectors.


b.

Measure the voltage on the wire harness side connector according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
3F-1 - Body ground W - Body ground Battery power supply Always 11 to 14 V
3K-1 - Body ground B-R - Body ground Battery power supply Always 11 to 14 V

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Measure the resistance on the wire harness side connector according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
3D-3 - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction in the wire harness.


d.

Reconnect the instrument panel junction block assembly and main body ECU (multiplex network body ECU) connectors.


e.

Measure the voltage and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
3H-30 - Body ground G - Body ground Taillights and license plate lights drive output Light control switch in tail or head position 11 to 14 V
Light control switch off*1 Below 1 V
3A-52 - Body ground L - Body ground Front fog light drive output Light control switch in tail or head position, fog light switch in front position Below 1 V
Light control switch in tail or head position, fog light switch off 11 to 14 V
3H-21 - Body ground*2 BE - Body ground Rear fog light drive output Light control switch in tail or head position, fog light switch in rear position 11 to 14 V
Light control switch in tail or head position, fog light switch off Below 1 V
3F-31 - Body ground G - Body ground H-LP LH relay drive output power switch off 11 to 14 V
power switch ON Below 1 V
F15-1 (DIM) - Body ground Y - Body ground H-LP RH relay drive output power switch off 11 to 14 V
power switch ON Below 1 V
F15-8 (A) - Body ground W - Body ground Light control switch AUTO position signal input Light control switch in AUTO position Below 1 V
Light control switch not in AUTO position Pulse generation
F15-10 (HF) - Body ground LG - Body ground Dimmer switch high flash position signal input Dimmer switch in high flash position Below 1 V
Dimmer switch not in high flash position Pulse generation
F15-12 (HEAD) - Body ground L - Body ground Light control switch head position input Light control switch in head position Below 1 V
Light control switch not in head position Pulse generation
F15-19 (CLTB) - F15-21 (CLTE) G - V Automatic light control sensor power supply output power switch off Below 1 V
power switch ON 11 to 14 V
F15-20 (CLTS) - Body ground BE - Body ground Automatic light control sensor signal input power switch off Below 1 V
Automatic light control system operating Communication waveform generation
(See waveform 1)
F15-22 (TAIL) - Body ground Y - Body ground Light control switch tail position signal input Light control switch in tail or head position Below 1 V
Light control switch not in tail or head position Pulse generation
F15-23 (RFOG) - Body ground*2 W - Body ground Fog light switch rear position input Fog light switch in rear position Below 1 V
Fog light switch off Pulse generation
F15-24 (HU) - Body ground GR - Body ground Dimmer switch high position signal input Dimmer switch in high position Below 1 V
Dimmer switch not in high position Pulse generation
F15-26 (FFOG) - Body ground R - Body ground Fog light switch front position input Fog light switch in front position Below 1 V
Fog light switch off Pulse generation
F16-4 (MILE) - Body ground*3 R - Body ground Door mirror foot lights drive output Door mirror foot light illuminates 11 to 14 V
Door mirror foot light off Below 3 V

*1: If the light switch has no OFF position, set the light switch to "Auto" with the Lo beam turned off. If the Lo beam is illuminated, shine a fluorescent light or other light source onto the light sensor to enter daytime mode.

*2: w/ Rear Fog Light

*3: w/ Door Mirror Foot Light


If the result is not as specified, the main body ECU (multiplex network body ECU) or instrument panel junction block assembly may be malfunctioning.

i.
E276298N01
2.844,1.646 3.219,1.813 0.375,0.167 10 false GND

Waveform 1

Item Content
Tester Connection F15-20 (CLTS) - Body ground
Tool setting 2 V/DIV., 10 ms./DIV.
Condition power switch on (IG)

HINT:

The communication waveform changes according to the surrounding brightness.





CHECK HEADLIGHT ECU SUB-ASSEMBLY LH (for TMC Made)


E334042E34
1.75,0.167 2.208,0.438 0.458,0.271 4.667,0.313 5.125,0.573 0.458,0.26 6.219,0.344 6.677,0.604 0.458,0.26 1.833,0.208 2.292,0.406 0.458,0.198 10 false A16 6.417,0.396 6.875,0.594 0.458,0.198 10 false C 4.865,0.365 5.323,0.563 0.458,0.198 10 false B

a.

Disconnect the A95 headlight ECU sub-assembly LH connector.


b.

Measure the resistance and voltage on the wire harness side connector according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A16-4 (IG) - Body ground V - Body ground Engine power supply power switch off Below 1 V
power switch on (IG) 11 to 14 V
A16-13 (ECUB) - Body ground L - Body ground Battery power supply Light control switch off Below 1 V
Light control switch in tail or head position 11 to 14 V
A16-12 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω


c.

Reconnect the A16 headlight ECU sub-assembly LH connector.

HINT:
·

Since the A16 headlight ECU sub-assembly LH connector is a waterproof type connector, the voltage cannot be measured and pulses cannot be checked for directly. The values listed are for reference only.

·

Since the B headlight ECU sub-assembly LH connector is connected inside the headlight assembly, the voltage cannot be measured and pulses cannot be checked for directly. The values listed are for reference only.




d.

Measure the voltage and check of pulses according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A16-15 (SGR) - Body ground BE - Body ground Rear height control sensor sub-assembly LH ground power switch on (IG) Below 1 Ω
A16-19 (LINS) - Body ground SB - Body ground LIN communication line power switch off Below 1 V
power switch on (IG) Pulse generation
A16-16 (SBR) - A16-15 (SGR) B - BE Rear height control sensor sub-assembly LH power supply power switch on (IG) 4.75 to 5.25 V
A16-17 (SHRL) - A16-15 (SGR) W - BE Rear height control sensor sub-assembly LH signal input power switch on (IG), vehicle unloaded, vehicle stopped Approximately 2.5 V
(value decreases as the front of the vehicle is raised)
A16-20 (LINL) - Body ground P - Body ground LIN communication line power switch off Below 1 V
power switch on (IG) Pulse generation
A16-21 (LCL) - Body ground GR - Body ground CAN communication line power switch off Below 1 V
power switch on (IG) Pulse generation
A16-22 (LCH) - Body ground G - Body ground CAN communication line power switch off Below 1 V
power switch on (IG) Pulse generation
A16-23 (CANL) - Body ground SB - Body ground CAN communication line power switch off Below 1 V
power switch on (IG) Pulse generation
A16-24 (CANH) - Body ground Y - Body ground CAN communication line power switch off Below 1 V
power switch on (IG) Pulse generation
B-2 (LOLED2) - B-3 (LOLED1) - Low beam headlights drive output Low beam headlights off Below 1 V
Low beam headlights on 11.2 to 17.7 V
B-3 (LOLED1) - Body ground - Low beam headlight LH drive ground Low beam headlight LH on Below 1 Ω
B-9 (ACTBI) - B-17 (ACTGI) - Headlight swivel and leveling motor LH power source power switch off Below 1 V
power switch on (IG) 11 to 14 V
B-17 (ACTGI) - Body ground - Headlight swivel and leveling motor LH ground power switch on (IG) Below 1 Ω
B-10 (DRL/CLL+) - B-1 (DRL/CLL-) - Parking light/daytime running light LH power source Parking light and daytime running light LH off Below 1 V
Parking light and daytime running light LH on 11 to 14 V
B-1 (DRL/CLL-) - Body ground - Parking light/daytime running light LH ground Parking light and daytime running light LH on Below 1 Ω
B-19 (HI SOL+) - B-11 (HI SOL-) - High beam headlight LH drive output High beam headlight LH off Below 1 V
High beam headlight LH on 11 to 14 V
B-11 (HI SOL-) - Body ground - High beam headlight LH ground High beam headlight LH on Below 1 Ω
C-4 (LINSI) - Body ground - LIN communication line power switch off Below 1 V
power switch on (IG) Pulse generation
C-13 (LINLI) - Body ground - LIN communication line power switch off Below 1 V
power switch on (IG) Pulse generation
B-16 (PWM1) - B-1 (DRL/CLL-) - Daytime running lights/clearance lights control signal output Daytime running lights and clearance lights off Below 1 V
Daytime running lights and clearance lights on Pulse generation
B-10 (DRL/CLL+) - B-1 (DRL/CLL-) - Daytime running lights/clearance lights power source Daytime running lights and clearance lights off Below 1 V
Daytime running lights and clearance lights on 11 to 14 V



CHECK HEADLIGHT ECU SUB-ASSEMBLY LH (for TMMT Made)


E334042E31
1.75,0.167 2.208,0.438 0.458,0.271 4.667,0.313 5.125,0.573 0.458,0.26 6.219,0.344 6.677,0.604 0.458,0.26 1.844,0.208 2.302,0.406 0.458,0.198 10 false A95 6.417,0.396 6.875,0.594 0.458,0.198 10 false C 4.865,0.365 5.323,0.563 0.458,0.198 10 false B

a.

Disconnect the A95 headlight ECU sub-assembly LH connector.


b.

Measure the resistance and voltage on the wire harness side connector according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A95-4 (IG) - Body ground V - Body ground Engine power supply power switch off Below 1 V
power switch on (IG) 11 to 14 V
A95-13 (ECUB) - Body ground L - Body ground Battery power supply Light control switch off Below 1 V
Light control switch in tail or head position 11 to 14 V
A95-12 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω


c.

Reconnect the A95 headlight ECU sub-assembly LH connector.

HINT:
·

Since the A95 headlight ECU sub-assembly LH connector is a waterproof type connector, the voltage cannot be measured and pulses cannot be checked for directly. The values listed are for reference only.

·

Since the B headlight ECU sub-assembly LH connector is connected inside the headlight assembly, the voltage cannot be measured and pulses cannot be checked for directly. The values listed are for reference only.




d.

Measure the voltage and check of pulses according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A95-15 (SGR) - Body ground BE - Body ground Rear height control sensor sub-assembly LH ground power switch on (IG) Below 1 Ω
A95-19 (LINS) - Body ground SB - Body ground LIN communication line power switch off Below 1 V
power switch on (IG) Pulse generation
A95-16 (SBR) - A95-15 (SGR) B - BE Rear height control sensor sub-assembly LH power supply power switch on (IG) 4.75 to 5.25 V
A95-17 (SHRL) - A95-15 (SGR) W - BE Rear height control sensor sub-assembly LH signal input power switch on (IG), vehicle unloaded, vehicle stopped Approximately 2.5 V
(value decreases as the front of the vehicle is raised)
A95-20 (LINL) - Body ground P - Body ground LIN communication line power switch off Below 1 V
power switch on (IG) Pulse generation
A95-21 (LCL) - Body ground GR - Body ground CAN communication line power switch off Below 1 V
power switch on (IG) Pulse generation
A95-22 (LCH) - Body ground G - Body ground CAN communication line power switch off Below 1 V
power switch on (IG) Pulse generation
A95-23 (CANL) - Body ground SB - Body ground CAN communication line power switch off Below 1 V
power switch on (IG) Pulse generation
A95-24 (CANH) - Body ground L - Body ground CAN communication line power switch off Below 1 V
power switch on (IG) Pulse generation
B-2 (LOLED2) - B-3 (LOLED1) - Low beam headlights drive output Low beam headlights off Below 1 V
Low beam headlights on 11.2 to 17.7 V
B-3 (LOLED1) - Body ground - Low beam headlight LH drive ground Low beam headlight LH on Below 1 Ω
B-9 (ACTBI) - B-17 (ACTGI) - Headlight swivel and leveling motor LH power source power switch off Below 1 V
power switch on (IG) 11 to 14 V
B-17 (ACTGI) - Body ground - Headlight swivel and leveling motor LH ground power switch on (IG) Below 1 Ω
B-10 (DRL/CLL+) - B-1 (DRL/CLL-) - Parking light/daytime running light LH power source Parking light and daytime running light LH off Below 1 V
Parking light and daytime running light LH on 11 to 14 V
B-1 (DRL/CLL-) - Body ground - Parking light/daytime running light LH ground Parking light and daytime running light LH on Below 1 Ω
B-19 (HI SOL+) - B-11 (HI SOL-) - High beam headlight LH drive output High beam headlight LH off Below 1 V
High beam headlight LH on 11 to 14 V
B-11 (HI SOL-) - Body ground - High beam headlight LH ground High beam headlight LH on Below 1 Ω
C-4 (LINSI) - Body ground - LIN communication line power switch off Below 1 V
power switch on (IG) Pulse generation
C-13 (LINLI) - Body ground - LIN communication line power switch off Below 1 V
power switch on (IG) Pulse generation
B-16 (PWM1) - B-1 (DRL/CLL-) - Daytime running lights/clearance lights control signal output Daytime running lights and clearance lights off Below 1 V
Daytime running lights and clearance lights on Pulse generation
B-10 (DRL/CLL+) - B-1 (DRL/CLL-) - Daytime running lights/clearance lights power source Daytime running lights and clearance lights off Below 1 V
Daytime running lights and clearance lights on 11 to 14 V



CHECK HEADLIGHT ECU SUB-ASSEMBLY RH


E334042E29
1.75,0.167 2.208,0.438 0.458,0.271 4.667,0.313 5.125,0.573 0.458,0.26 6.219,0.344 6.677,0.604 0.458,0.26 1.844,0.219 2.302,0.417 0.458,0.198 10 false A17 6.417,0.396 6.875,0.594 0.458,0.198 10 false C 4.865,0.365 5.323,0.563 0.458,0.198 10 false B

a.

Disconnect the A17 headlight ECU sub-assembly RH connector.


b.

Measure the resistance and voltage on the wire harness side connector according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A17-4 (IG) - Body ground V - Body ground Engine power supply power switch off Below 1 V
power switch on (IG) 11 to 14 V
A17-13 (ECUB) - Body ground L - Body ground Battery power supply Light control switch off* Below 1 V
Light control switch in tail or head position 11 to 14 V
A17-12 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

*: If the light switch has no OFF position, set the light switch to "Auto" with the Lo beam turned off. If the Lo beam is illuminated, shine a fluorescent light or other light source onto the light sensor to enter daytime mode.



c.

Reconnect the A17 headlight ECU sub-assembly RH connector.

HINT:
·

Since the A17 headlight ECU sub-assembly RH connector is a waterproof type connector, the voltage cannot be measured and pulses cannot be checked for directly. The values listed are for reference only.

·

Since the B headlight ECU sub-assembly RH connector is connected inside the headlight assembly, the voltage cannot be measured and pulses cannot be checked for directly. The values listed are for reference only.




d.

Measure the voltage and check of pulses according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A17-19 (LINS) - Body ground SB - Body ground LIN communication line power switch off Below 1 V
power switch on (IG) Pulse generation
A17-21 (LCL) - Body ground GR - Body ground CAN communication line power switch off Below 1 V
power switch on (IG) Pulse generation
A17-22 (LCH) - Body ground G - Body ground CAN communication line power switch off Below 1 V
power switch on (IG) Pulse generation
B-2 (LOLED2) - B-3 (LOLED1) - Low beam headlights drive output Low beam headlights off Below 1 V
Low beam headlights on 13.38 to 19.62 V
B-3 (LOLED1) - Body ground - Low beam headlight RH drive ground Low beam headlight RH on Below 1 Ω
B-9 (ACTBI) - B-17 (ACTGI) - Headlight swivel and leveling motor RH power source power switch off Below 1 V
power switch on (IG) 11 to 14 V
B-17 (ACTGI) - Body ground - Headlight swivel and leveling motor RH ground power switch on (IG) Below 1 Ω
B-10 (DRL/CLL+) - B-1 (DRL/CLL-) - Parking light/daytime running light RH power source Parking light and daytime running light RH off Below 1 V
Parking light and daytime running light RH on 11 to 14 V
B-1 (DRL/CLL-) - Body ground - Parking light/daytime running light RH ground Parking light and daytime running light RH on Below 1 Ω
B-19 (HI SOL+) - B-11 (HI SOL-) - High beam headlight RH drive output High beam headlight RH off Below 1 V
High beam headlight RH on 11 to 14 V
B-11 (HI SOL-) - Body ground - High beam headlight RH ground High beam headlight RH on Below 1 Ω
C-4 (LINSI) - Body ground - LIN communication line power switch off Below 1 V
power switch on (IG) Pulse generation
C-13 (LINLI) - Body ground - LIN communication line power switch off Below 1 V
power switch on (IG) Pulse generation
B-16 (PWM1) - B-1 (DRL/CLL-) - Daytime running lights/clearance lights control signal output Daytime running lights and clearance lights off Below 1 V
Daytime running lights or clearance lights on Pulse generation
B-10 (DRL/CLL+) - B-1 (DRL/CLL-) - Daytime running lights/clearance lights power source Daytime running lights and clearance lights off Below 1 V
Daytime running lights or clearance lights on 11 to 14 V