DATA LIST
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Connect the GTS to the DLC3.
Turn the power switch to on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / AFS / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Front Window Washer Switch | Front window washer switch signal | ON or OFF | ON: Front window washer switch on
OFF: Front window washer switch off |
- |
| Clearance Light State | Clearance light state | ON or OFF | ON: Clearance lights on
OFF: Clearance lights off |
- |
| +B Voltage Value | Headlight ECU sub-assembly LH +B power supply voltage value | 0 to 19.75 V | 11.00 to 14.00 V | - |
| Traveling Direction | Traveling direction | Not Fwd or Fwd | Not Fwd: Shift lever in R or N
Fwd: Shift lever not in R or N |
- |
| Steering Sensor Initialization Status | Steering sensor initialization state | Incomplete or Completed | Incomplete: Steering sensor zero point calibration incomplete
Completed: Steering sensor zero point calibration complete |
- |
| Headlight Low Beam State | Low beam headlight state | ON or OFF | ON: Low beam headlights on
OFF: Low beam headlights off |
- |
| Headlight High Beam State | High beam headlight state | ON or OFF | ON: High beam headlights on
OFF: High beam headlights off |
- |
| DRL State | Daytime running light state | OFF or ON | OFF: Daytime running light LH off
ON: Daytime running light LH on |
- |
| Engine | Engine condition | Stop or Run | Stop: Engine is stopped
Run: Engine is running |
- |
| +B | Headlight ECU sub-assembly LH IG power supply voltage value | 0 to 19.75 V | 11.00 to 14.00 V | - |
| Height Sens Pw Supply Val | Rear height control sensor sub-assembly LH power supply value | 0.00 to 6.25 V | 4.61 to 5.00 V | - |
| Rr Height Sens Signal Val | Rear height control sensor sub-assembly LH signal value | 0.00 to 5.00 V | 0.50 to 4.50 V | Value changes according to vehicle height |
| Steering Sens Signal | Steering sensor signal value | -384.0 to 382.5 deg | Changes according to the operation of the steering wheel | Turning left: Increases
Turning right: Decreases |
| Steering Sens Center Pos | Steering sensor center position | -3072.0 to 3070.5 deg | 0.0 deg (tires straight ahead) | - |
| FR Wheel Speed | Front right wheel speed | 0.00 to 260.00 km/h (162.00 mph) | Vehicle stopped: 0 km/h (0 mph) | - |
| FL Wheel Speed | Front left wheel speed | 0.00 to 260.00 km/h (162.00 mph) | Vehicle stopped: 0 km/h (0 mph) | - |
| Vehicle Speed | Vehicle speed | 0.00 to 260.00 km/h (162.00 mph) | Vehicle stopped: 0 km/h (0 mph) | - |
| Rear Height Adjust Valid Flag | Rear height adjustment range | Valid or Invalid | Inval: Rear height control sensor sub-assembly LH value out of normal range
Valid: Rear height control sensor sub-assembly LH value within normal range |
- |
| Init Writing Count | Number of times initialization performed | 0 to 255 | Number of times initialization performed | - |
| Sensor Initialization Hist | Sensor initialization history | not comp, 10%, 25%, 50%, 75%, 100% or completed | ·
not comp: Headlight ECU sub-assembly LH not initialized after replacing. ·
10%: Initialization completed when fuel tank was 10% full ·
25%: Initialization completed when fuel tank was 25% full ·
50%: Initialization completed when fuel tank was 50% full ·
75%: Initialization completed when fuel tank was 75% full ·
100%: Initialization completed when fuel tank was 100% full ·
completed: ECU not replaced and ECU has not been initialized at workshop. |
- |
| Number Of Trouble Codes | Number of trouble codes | 0 to 255 | Number of stored DTCs displayed | - |
ACTIVE TEST
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the GTS to the DLC3.
Turn the power switch to on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / AFS / Active Test.
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Drive The Leveling Motor | Headlight swivel and leveling motor upward or downward operation | Stop, Down or Up | Perform the Active Test with the engine is running and vehicle stopped |
| AFS OFF Indicator | "Headlight System Malfunction Visit Your Dealer." display | ON or OFF | - |
| Clearance Light | Clearance lights | ON or OFF | - |
| Headlight Low Beam | Low beam headlights | ON or OFF | - |
| Headlight High Beam | High beam headlights | ON or OFF | - |
| Daytime Running Light | Daytime running lights | ON or OFF | - |