Home › Engine / Hybrid System › 2ZR-FXE (ENGINE CONTROL) › SFI SYSTEM › from 2020.08
RM32K0E _51 Engine / Hybrid System _060312 2ZR-FXE ENGINE CONTROL _0295698 SFI SYSTEM U

2ZR-FXE ENGINE CONTROL  SFI SYSTEM  TERMINALS OF ECM  


A335752E48
2.344,0.375 2.792,0.677 0.448,0.302 5.771,0.417 6.219,0.719 0.448,0.302 2.427,0.448 2.885,0.646 0.458,0.198 10 false C63 5.854,0.479 6.313,0.677 0.458,0.198 10 false A38

HINT:

The standard voltage, resistance and waveform between each pair of the ECM terminals is shown in the table below. The appropriate conditions for checking each pair of the terminals is also indicated. The result of checks should be compared with the standard voltage, resistance and waveform for each pair of the terminals as displayed in the Specified Condition column. The illustration above can be used as a reference to identify the ECM terminal locations.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A38-1 (BATT) - C63-59 (E1) B - W-B Auxiliary battery (for measuring auxiliary battery voltage and for ECM memory) Power switch off 11 to 16 V
A38-2 (+B) - C63-59 (E1) R - W-B Power source of ECM Engine stopped, power switch on (IG) 11 to 14 V
A38-3 (+B2) - C63-59 (E1) R - W-B Power source of ECM Engine stopped, power switch on (IG) 11 to 14 V
A38-6 (IGSW) - C63-59 (E1) BE - W-B Power switch signal Engine stopped, power switch on (IG) 11 to 14 V
A38-7 (FANL) - C63-59 (E1) L - W-B Cooling fan motor operation signal (low) Power switch on (IG) 11 to 14 V
Idling, high engine coolant temperature Below 1.5 V
A38-8 (FANH) - C63-59 (E1) LG - W-B Cooling fan motor operation signal (high) Power switch on (IG) 11 to 14 V
Idling, high engine coolant temperature Below 1.5 V
A38-13 (CANH) - C63-59 (E1) GR*2 - W-B
R*3 - W-B
CAN communication line Engine stopped, power switch on (IG) Pulse generation
(See waveform 1)
A38-26 (CANL) - C63-59 (E1) P - W-B CAN communication line Engine stopped, power switch on (IG) Pulse generation
(See waveform 2)
A38-30 (NEO) - C63-59 (E1) L - W-B Crankshaft revolution signal Idling with warm engine Pulse generation
(See waveform 3)
A38-32 (EC) - Body ground W-B - - Ground Always Below 1 Ω
A38-41 (FC) - C63-59 (E1) V - W-B Fuel pump control Engine stopped, power switch on (IG) 11 to 14 V
Idling Below 1.5 V
A38-46 (MREL) - C63-59 (E1) G - W-B EFI-MAIN relay operation signal Engine stopped, power switch on (IG) 11 to 14 V
C63-26 (E04) - Body ground W-B - - Ground Always Below 1 Ω
C63-27 (HA1A) - C63-26 (E04) W - W-B Air fuel ratio sensor heater operation signal Engine stopped, power switch on (IG) 11 to 14 V
Idling with cold engine Pulse generation
(See waveform 5)
C63-28 (ME01) - Body ground W-B - - Ground Always Below 1 Ω
C63-29 (+BM) - C63-59 (E1) LG - W-B Power source of throttle actuator Power switch off 11 to 16 V
C63-30 (M-) - C63-28 (ME01) P - W-B Throttle actuator operation signal (negative signal) Idling with warm engine Pulse generation
(See waveform 6)
C63-31 (CAN+) - C63-59 (E1) L - W-B CAN communication line Engine stopped, power switch on (IG) Pulse generation
(See waveform 1)
C63-32 (CAN-) - C63-59 (E1) W - W-B CAN communication line Engine stopped, power switch on (IG) Pulse generation
(See waveform 2)
C63-33 (PRG) - C63-59 (E1) V - W-B Purge VSV operation signal Engine stopped, power switch on (IG) 11 to 14 V
Idling with warm engine, under purge control Pulse generation
(See waveform 7)
C63-35 (OC1+) - C63-34 (OC1-) L - G Camshaft timing oil control valve assembly operation signal Idling Pulse generation
(See waveform 8)
C63-56 (HT1B) - C63-26 (E04) G - W-B Heated oxygen sensor heater operation signal Engine stopped, power switch on (IG) 11 to 14 V
Idling with cold engine Below 3.0 V
C63-57 (E01) - Body ground W-B - - Ground Always Below 1 Ω
C63-58 (E02) - Body ground W-B - - Ground Always Below 1 Ω
C63-59 (E1) - Body ground W-B - - Ground Always Below 1 Ω
C63-60 (M+) - C63-28 (ME01) V - W-B Throttle actuator operation signal (positive terminal) Idling with warm engine Pulse generation
(See waveform 9)
C63-62 (WSV)*1 - C63-59 (E1) G - W-B Flow shutting valve (water valve) operation signal Engine stopped, power switch on (IG) 11 to 14 V
C63-68 (WPI) - C63-59 (E1) P - W-B Engine water pump assembly signal Idling with warm engine Pulse generation
(See waveform 10)
C63-69 (WPO) - C63-59 (E1) LG - W-B Engine water pump assembly signal Idling with warm engine Pulse generation
(See waveform 11)
C63-70 (G2O) - C63-59 (E1) W - W-B Camshaft revolution signal Idling with warm engine Pulse generation
(See waveform 12)
C63-71 (IGF1) - C63-59 (E1) L - W-B Ignition coil assembly signal
(ignition confirmation signal)
Power switch on (IG) 4.5 to 5.5 V
Idling with warm engine Pulse generation
(See waveform 13)
C63-72 (IGT4) - C63-59 (E1) V - W-B Ignition coil assembly (No. 4 cylinder) signal
(ignition signal)
Idling with warm engine Pulse generation
(See waveform 13)
C63-73 (IGT3) - C63-59 (E1) G - W-B Ignition coil assembly (No. 3 cylinder) signal
(ignition signal)
Idling with warm engine Pulse generation
(See waveform 13)
C63-74 (IGT2) - C63-59 (E1) B - W-B Ignition coil assembly (No. 2 cylinder) signal
(ignition signal)
Idling with warm engine Pulse generation
(See waveform 13)
C63-75 (IGT1) - C63-59 (E1) GR - W-B Ignition coil assembly (No. 1 cylinder) signal
(ignition signal)
Idling with warm engine Pulse generation
(See waveform 13)
C63-77 (VCPM) - C63-76 (EPIM) GR - V Power source of manifold absolute pressure sensor Engine stopped, power switch on (IG) 4.75 to 5.25 V
C63-78 (PIM) - C63-76 (EPIM) B - V Manifold absolute pressure sensor signal Engine stopped, power switch on (IG) 3.0 to 4.5 V
C63-82 (VV1+) - C63-115 (VV1-) SB - G Camshaft position sensor signal Idling with warm engine Pulse generation
(See waveform 14)
C63-86 (PEX)*4 - C63-118 (EPEX)*4 B - GR Differential pressure sensor signal Power switch on (IG) 0.4 to 4.8 V
C63-95 (#20) - C63-57 (E01) LG - W-B Fuel injector assembly (No. 2 cylinder) signal Idling with warm engine Pulse generation
(See waveform 15)
C63-96 (#30) - C63-57 (E01) L - W-B Fuel injector assembly (No. 3 cylinder) signal Idling with warm engine Pulse generation
(See waveform 15)
C63-97 (#40) - C63-57 (E01) R - W-B Fuel injector assembly (No. 4 cylinder) signal Idling with warm engine Pulse generation
(See waveform 15)
C63-98 (#10) - C63-57 (E01) BE - W-B Fuel injector assembly (No. 1 cylinder) signal Idling with warm engine Pulse generation
(See waveform 15)
C63-99 (OX1B) - C63-131 (EX1B) V - P Heated oxygen sensor signal Engine speed maintained at 2500 rpm for 2 minutes after warming up engine Pulse generation
(See waveform 16)
C63-100 (A1A+) - C63-59 (E1) Y - W-B Air fuel ratio sensor signal Engine stopped, power switch on (IG) 3.0 to 3.6 V*1
C63-101 (VTA2) - C63-133 (ETA) B - G Throttle position sensor signal (for sensor malfunction detection) Engine stopped, power switch on (IG), accelerator pedal fully released 2.1 to 3.1 V
C63-105 (EGR4) - C63-59 (E1) LG - W-B EGR valve assembly signal EGR valve assembly operating Pulse generation
(See waveform 17)
C63-106 (EGR2) - C63-59 (E1) R - W-B EGR valve assembly signal EGR valve assembly operating Pulse generation
(See waveform 17)
C63-107 (EGR3) - C63-59 (E1) BE - W-B EGR valve assembly signal EGR valve assembly operating Pulse generation
(See waveform 17)
C63-108 (GE01) - Body ground BR - - Shielded (ground) circuit of throttle actuator Always Below 1 Ω
C63-114 (NE+) - C63-113 (NE-) B - W Crankshaft position sensor signal Idling with warm engine Pulse generation
(See waveform 18)
C63-116 (VCV1) - C63-59 (E1) R - W-B Power source of camshaft position sensor Engine stopped, power switch on (IG) 4.5 to 5.5 V
C63-117 (VCPX)*4 - C63-118 (EPEX)*4 L - GR Power source of differential pressure sensor (specific voltage) Power switch on (IG) 4.5 to 5.5 V
C63-120 (THW) - C63-119 (ETHW) Y - BR Engine coolant temperature sensor signal Idling, engine coolant temperature 75 to 100°C (167 to 212°F) 0.2 to 1.0 V
C63-122 (KNK1) - C63-121 (EKNK) B - W Knock sensor signal Engine speed maintained at 2500 rpm after warming up engine Pulse generation
(See waveform 19)
C63-129 (THHW) - C63-130 (ETHH) P - BR No. 2 engine coolant temperature sensor signal Idling, engine coolant temperature 75 to 100°C (167 to 212°F) 0.2 to 1.0 V
C63-132 (A1A-) - C63-59 (E1) BR - W-B Air fuel ratio sensor signal Engine stopped, power switch on (IG) 2.7 to 3.3 V*1
C63-134 (VCTA) - C63-133 (ETA) R - G Power source of throttle position sensor (specific voltage) Engine stopped, power switch on (IG) 4.5 to 5.5 V
C63-135 (VTA1) - C63-133 (ETA) BE - G Throttle position sensor signal (for engine control) Engine stopped, power switch on (IG), accelerator pedal fully released 0.6 to 1.1 V
C63-137 (VG) - C63-104 (E2G) G - L Mass air flow meter signal Idling, park (P) or neutral (N) selected, A/C switch off 0.5 to 3.0 V
C63-138 (THA) - C63-139 (ETHA) V - GR Intake air temperature sensor (mass air flow meter) signal Idling, intake air temperature 0 to 80°C (32 to 176°F) 0.5 to 3.4 V
C63-140 (EGR1) - C63-59 (E1) P - W-B EGR valve assembly signal EGR valve assembly operating Pulse generation
(See waveform 17)

*1: The ECM terminal voltage is constant regardless of the voltage output from the sensor.

*2: for TMMT made

*3: for TMC made

*4: w/ Differential Pressure Sensor


WAVEFORM 1


A283576E01
2.75,0.292 3.354,0.583 0.604,0.292 10 1 V/DIV. 3.01,1.396 3.344,1.708 0.333,0.313 10 GND 1.604,1.896 2.479,2.125 0.875,0.229 10 10 μs./DIV.

CAN Communication Signal (Reference)
ECM Terminal Name Between CANH and E1
Between CAN+ and E1
Tester Range 1 V/DIV., 10 μs./DIV.
Condition Engine stopped, power switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.



WAVEFORM 2


A283577E01
2.76,0.271 3.375,0.531 0.615,0.26 10 1 V/DIV. 3.01,1.365 3.375,1.604 0.365,0.24 10 GND 1.625,1.865 2.583,2.052 0.958,0.188 10 10 μs./DIV.

CAN Communication Signal (Reference)
ECM Terminal Name Between CANL and E1
Between CAN- and E1
Tester Range 1 V/DIV., 10 μs./DIV.
Condition Engine stopped, power switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.



WAVEFORM 3


A214025E27
2.987,1.794 3.317,1.950 0.330,0.156 10 GND 1.269,2.584 2.024,2.772 0.756,0.188 10 20 ms./DIV. 2.394,0.238 2.939,0.405 0.545,0.167 10 5 V/DIV.

Crankshaft Revolution Signal from ECM to Inverter with Converter Assembly
ECM Terminal Name Between NEO and E1
Tester Range 5 V/DIV., 20 ms./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 4


A205412E04
2.594,0.063 3.208,0.375 0.615,0.313 10 5 V/DIV. 2.688,0.896 3.104,1.24 0.417,0.344 10 GND 1.219,1.854 1.979,2.031 0.76,0.177 10 10 ms./DIV.

Air Fuel Ratio Sensor Heater Operation Signal
ECM Terminal Name Between HA1A and E04
Tester Range 5 V/DIV., 10 ms./DIV.
Condition Idling with cold engine


WAVEFORM 5


A245848E22
2.854,1 3.323,1.354 0.469,0.354 10 GND 2.625,0.313 3.323,0.594 0.698,0.281 10 5 V/DIV. 0.479,0.625 0.844,0.875 0.365,0.25 10 M- 1.417,1.802 2.573,2.052 1.156,0.25 10 1 ms./DIV.

Throttle Actuator Negative Terminal Signal
ECM Terminal Name Between M- and ME01
Tester Range 5 V/DIV., 1 ms./DIV.
Condition Idling with warm engine

HINT:

The duty ratio varies depending on the throttle actuator operation.



WAVEFORM 6


A218020E05
2.677,0.208 3.344,0.51 0.667,0.302 10 10 V/DIV. 2.802,0.938 3.292,1.26 0.49,0.323 10 GND 1.26,1.771 2.25,2.021 0.99,0.25 10 20 ms./DIV.

Purge VSV Operation Signal
ECM Terminal Name Between PRG and E1
Tester Range 10 V/DIV., 20 ms./DIV.
Condition Idling with warm engine, under purge control

HINT:

If the waveform is not similar to the illustration, check the waveform again after idling for 10 minutes or more.



WAVEFORM 7


A283575E01
0.604,0.26 1.563,0.573 0.958,0.313 10 5 V/DIV. 0.51,1.125 1.021,1.385 0.51,0.26 10 GND 1.729,1.844 2.583,2.063 0.854,0.219 10 1 ms./DIV.

Camshaft Timing Oil Control Valve Assembly Operation Signal
ECM Terminal Name Between OC1+ and OC1-
Tester Range 5 V/DIV., 1 ms./DIV.
Condition Idling


WAVEFORM 8


A208000E20
2.854,0.99 3.313,1.302 0.458,0.313 10 GND 2.635,0.26 3.313,0.552 0.677,0.292 10 5 V/DIV. 0.521,0.656 0.99,0.948 0.469,0.292 10 M+ 1.396,1.802 2.281,2.021 0.885,0.219 10 1 ms./DIV.

Throttle Actuator Positive Terminal Signal
ECM Terminal Name Between M+ and ME01
Tester Range 5 V/DIV., 1 ms./DIV.
Condition Idling with warm engine

HINT:

The duty ratio varies depending on the throttle actuator operation.



WAVEFORM 9


A214025E24
2.987,1.794 3.317,1.950 0.330,0.156 10 GND 1.269,2.584 2.024,2.772 0.756,0.188 10 20 ms./DIV. 2.394,0.238 2.939,0.405 0.545,0.167 10 5 V/DIV.

Engine Water Pump Assembly Signal (from Engine Water Pump Assembly to ECM)
ECM Terminal Name Between WPI and E1
Tester Range 5 V/DIV., 20 ms./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine water pump speed increases.



WAVEFORM 10


A214025E24
2.987,1.794 3.317,1.950 0.330,0.156 10 GND 1.269,2.584 2.024,2.772 0.756,0.188 10 20 ms./DIV. 2.394,0.238 2.939,0.405 0.545,0.167 10 5 V/DIV.

Engine Water Pump Assembly Signal (from ECM to Engine Water Pump Assembly)
ECM Terminal Name Between WPO and E1
Tester Range 5 V/DIV., 20 ms./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine water pump speed increases.



WAVEFORM 11


A214025E25
2.987,1.794 3.317,1.950 0.330,0.156 10 GND 1.269,2.584 2.024,2.772 0.756,0.188 10 20 ms./DIV. 2.394,0.238 2.939,0.405 0.545,0.167 10 5 V/DIV.

Camshaft Revolution Signal from ECM to Inverter with Converter Assembly
ECM Terminal Name Between G2O and E1
Tester Range 5 V/DIV., 20 ms./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 12


A289263E05
2.844,0.854 3.208,1.052 0.365,0.198 10 false GND 2.844,1.5 3.177,1.698 0.333,0.198 10 false GND 0.042,0.417 0.365,0.927 0.323,0.51 10 false CH1 (IGT) 0.021,1.198 0.406,1.823 0.385,0.625 10 false CH2 (IGF1) 0.031,0.031 0.573,0.208 0.542,0.177 10 false 2 V/DIV. 1.156,1.844 1.906,1.99 0.75,0.146 10 false 20 ms./DIV.

Ignition Coil Assembly Signal (IGT and IGF Signal)
ECM Terminal Name CH1: Between IGT (1 to 4) and E1
CH2: Between IGF1 and E1
Tester Range 2 V/DIV., 20 ms./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 13


A254147E02
2.986,0.993 3.323,1.140 0.336,0.147 10 GND 1.159,1.916 1.902,2.062 0.744,0.147 10 20 ms./DIV. 2.748,0.059 3.284,0.206 0.536,0.147 10 5 V/DIV.

Camshaft Position Sensor Signal
ECM Terminal Name Between VV1+ and VV1-
Tester Range 5 V/DIV., 20 ms./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 14


A287799E11
0.656,1.583 1.115,1.781 0.458,0.198 10 false GND 0.396,0.115 1.063,0.344 0.667,0.229 10 false 20 V/DIV. 1.833,1.896 2.646,2.083 0.813,0.188 10 false 20 ms./DIV.

Fuel Injector Assembly Signal
ECM Terminal Name Between #10 (to #40) and E01
Tester Range 20 V/DIV., 20 ms./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 15


A283571E01
0.51,0.219 1.292,0.521 0.781,0.302 10 0.2 V/DIV. 0.573,1.479 1.021,1.76 0.448,0.281 10 GND 1.802,1.875 2.771,2.115 0.969,0.24 10 200 ms./DIV.

Heated Oxygen Sensor Signal
ECM Terminal Name Between OX1B and EX1B
Tester Range 0.2 V/DIV., 200 ms./DIV.
Condition Engine speed maintained at 2500 rpm for 2 minutes after warming up engine

HINT:

Data List item "O2 Sensor Voltage B1S2" shows the ECM values from the heated oxygen sensor.



WAVEFORM 16


A214026E05
2.849,2.294 3.179,2.450 0.330,0.156 10 GND 2.849,1.922 3.179,2.077 0.330,0.156 10 GND 2.849,1.578 3.179,1.734 0.330,0.156 10 GND 2.849,1.24 3.179,1.396 0.330,0.156 10 GND 0.235,1.039 0.686,1.195 0.451,0.156 10 EGR1 0.235,1.405 0.686,1.560 0.451,0.156 10 EGR2 0.235,1.757 0.686,1.913 0.451,0.156 10 EGR3 0.235,2.113 0.686,2.269 0.451,0.156 10 EGR4 1.248,2.42 1.997,2.577 0.749,0.157 10 50 ms./DIV. 1.979,0.406 2.643,0.581 0.665,0.175 10 20 V/DIV.

EGR Valve Assembly Signal
ECM Terminal Name Between EGR1 ( to EGR4) and E1
Tester Range 20 V/DIV., 50 ms./DIV.
Condition EGR valve assembly operating


WAVEFORM 17


A254145E10
2.984,0.964 3.337,1.167 0.353,0.202 10 GND 0.067,0.058 0.612,0.235 0.545,0.177 10 5 V/DIV. 1.22,1.917 1.972,2.062 0.751,0.145 10 20 ms./DIV.

Crankshaft Position Sensor Signal
ECM Terminal Name Between NE+ and NE-
Tester Range 5 V/DIV., 20 ms./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 18


A283572E01
2.427,0.521 3.208,0.865 0.781,0.344 10 1 V/DIV. 2.615,1 3.115,1.292 0.5,0.292 10 GND 1.115,1.865 2.01,2.083 0.896,0.219 10 1 ms./DIV.

Knock Sensor Signal
ECM Terminal Name Between KNK1 and EKNK
Tester Range 1 V/DIV., 1 ms./DIV.
Condition Engine speed maintained at 2500 rpm after warming up engine

HINT:
·

The wavelength becomes shorter as the engine speed increases.

·

The waveforms and amplitudes displayed will differ slightly depending on the vehicle.