PARTICULATE FILTER REGENERATION PROCEDURE
PM Regenerate Mode is a procedure in which accumulated PM (Particulate Matter) in the GPF (Gasoline Particulate Filter) is forcibly oxidized.
This procedure increases the temperature of the GPF and promotes oxidization by a lean condition.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher with all the accessories switched off.
Enter the following menus: Powertrain / Engine / Utility / PM Regenerate Mode.
| Tester Display |
|---|
| PM Regenerate Mode |
Turn the GTS off.
Disconnect the GTS.
The vehicle will remain in PM Regenerate Mode even if the GTS is disconnected from the DLC3.
To end PM Regenerate Mode, turn the power switch off.
Turn the A/C switch on.
Drive the vehicle at a speed of 60 km/h (37 mph) or more until the GPF warning light turns off, or "Exhaust Filter Regeneration In Process" or "Exhaust Filter Full" is no longer displayed on the multi-information display.
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Before driving, check that no DTCs other than those related to the GPF (Gasoline Particulate Filter) system are stored.
When in PM Regenerate Mode, for hybrid vehicles, the engine speed during forced particulate filter regeneration will be higher than normal.
When the vehicle is driven in a manner in which particulate filter regeneration is performed, the GPF warning light will blink at a 2 second interval or "Exhaust Filter Regeneration" will be displayed on the multi-information display.
Particulate filter regeneration can be judged as being performed based on the GPF warning light state or display of "Exhaust Filter Regeneration" on the multi-information display.
If the vehicle speed decreases due to traffic conditions, etc. and particulate filter regeneration stops, it will continue when the vehicle speed is increased.
Continuously drive the vehicle at a speed of 60 km/h (37 mph) or more to perform particulate filter regeneration.
The engine speed will be adjusted automatically, so drive in the D range.
While the vehicle is in PM Regenerate Mode, the MIL or go to service warning light may illuminate and engine output may be restricted, but if particulate filter regeneration is being performed, it will continue.
Driving on roads which allow high speed driving (90 to 100 km/h (56 to 62 mph)), such as a freeway, can reduce the time it takes to perform particulate filter regeneration.
Engine braking may be not as effective during PM Regenerate Mode.
When the accumulated PM has dropped below a certain amount, the GPF warning light will turn off, or "Exhaust Filter Regeneration In Process" or "Exhaust Filter Full" will no longer be displayed on the multi-information display.
If forced particulate filter regeneration is performed at the request of the customer (for example: "Exhaust Filter Full" is displayed on the multi-information display), it will continue until the PM Deposition Ratio is 30% or less.
If the GPF warning light does not turn off or "Exhaust Filter Regeneration In Process" or "Exhaust Filter Full" continues to be displayed on the multi-information display after the vehicle is driven at a speed of 60 km/h (37 mph) or more for 60 minutes or more to perform particulate filter regeneration, check the Vehicle Control History.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Utility / Vehicle Control History (RoB).
| Tester Display |
|---|
| Vehicle Control History (RoB) |
Forced particulate filter regeneration is typically only necessary for users who frequently drive only short trips, where the temperature of the GPF catalyst does not increase sufficiently to oxidize PM. If the value of the Data List item "PM Deposition Ratio Bank1" is more than 30%, advice the customer to occasionally drive longer than normal, in order to help reduce the accumulation of PM.
If the vehicle cannot be driven a long distance or for a long time, replace the GPF.
Click hereEngine / Hybrid System>2ZR-FXE (INTAKE / EXHAUST)>EXHAUST PIPE>REMOVAL