Home › Drivetrain › P610 (HYBRID TRANSMISSION / TRANSAXLE) › MOTOR CABLE › from 2020.08
RM32K0E _52 Drivetrain _059722 P610 HYBRID TRANSMISSION / TRANSAXLE _0292761 MOTOR CABLE A

P610 HYBRID TRANSMISSION / TRANSAXLE  MOTOR CABLE  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during motor cable removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Panoramic view monitor system (Click here)
Replacement of ECM Perform Vehicle Identification Number (VIN) registration MIL comes on (Click here)
Replacement of inverter with converter assembly Resolver learning
·

DTCs are stored

·

Slight vibration at a vehicle speed of 5 km/h (3 mph) or less

·

Shock or vibration during acceleration


for Nickel Metal Hydride Battery:
(Click here)
for Lithium-ion Battery:
(Click here)

CAUTION:
·
A340386

Orange wire harnesses and connectors indicate high-voltage circuits. To prevent electric shock, always follow the procedure described in the repair manual.

for NICKEL METAL HYDRIDE BATTERY:

Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)>PRECAUTION

for LITHIUM-ION BATTERY:

Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY)>PRECAUTION

·
A340358

To prevent electric shock, wear insulated gloves when working on wire harnesses and components of the high voltage system.



HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link

*1: When performing learning using the GTS

Click here(Click here)

Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Simple intelligent parking assist system*1
Parking support brake system*1
Toyota parking assist-sensor system*1

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide G9200 1.REMOVE INVERTER WITH CONVERTER ASSEMBLY

Hide G1148 2.REMOVE MOTOR CABLE

CAUTION:

Be sure to wear insulated gloves.


a.
C343106

Remove the 2 bolts and connector cover from the hybrid vehicle transaxle assembly.


b.
C343107

Disengage the 2 claws to remove the terminal cap from the hybrid vehicle transaxle assembly.


c.
C350458C01
1.167,3.24 1.281,3.24 1.281,3.24 1.375,3.073 false 1.01,3.156 1.26,3.344 0.25,0.188 10 false *a
*a Waterproof Seal


Using an insulated tool, remove the 6 bolts and motor cable from the hybrid vehicle transaxle assembly.

NOTICE:
·

Keep the motor cable terminals and their installation area free from foreign matter, water, etc.

·

Do not touch the waterproof seal or terminals of the motor cable.

·

Cover the hole where the motor cable was installed with tape or equivalent (non-residue type) to prevent entry of foreign matter.