When removing the name plates, heat the vehicle body, back door outside garnish, front bumper assembly and name plates using a heat light.
| Item | Temperature |
|---|---|
| Vehicle Body | 40 to 60°C (104 to 140°F) |
·
Back Door Outside Garnish ·
Front Bumper Assembly ·
Name Plate |
20 to 30°C (68 to 86°F) |
| *a | Heated Part |
| *b | Heat Light |
Do not touch the heat light and heated parts, touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.
Do not heat the vehicle body, back door outside garnish, front bumper assembly or name plate excessively.
75442A
1.REMOVE NO. 2 BACK DOOR NAME PLATE
| *a | Wooden Block |
| *b | Piano Wire |
|
Protective Tape |
Apply protective tape around the No. 2 back door name plate as shown in the illustration.
Insert a piano wire between the back door outside garnish and No. 2 back door name plate.
Tie objects that can serve as handles (for example, wooden blocks) to both wire ends.
Pull the piano wire and cut the double-sided tape that holds the No. 2 back door name plate to the back door outside garnish to remove the No. 2 back door name plate.
Be careful not to damage the back door outside garnish.
Remove the protective tape.
75441E
2.REMOVE NO. 1 BACK DOOR NAME PLATE
| *a | Wooden Block |
| *b | Piano Wire |
|
Protective Tape |
Apply protective tape around the No. 1 back door name plate as shown in the illustration.
Insert a piano wire between the back door outside garnish and No. 1 back door name plate.
Tie objects that can serve as handles (for example, wooden blocks) to both wire ends.
Pull the piano wire and cut the double-sided tape that holds the No. 1 back door name plate to the back door outside garnish to remove the No. 1 back door name plate.
Be careful not to damage the back door outside garnish.
Remove the protective tape.
75431A
3.REMOVE NO. 1 BACK DOOR EMBLEM
| *a | Location Pin |
|
Protective Tape |
Apply protective tape around the No. 1 back door emblem as shown in the illustration.
Using a moulding remover D, separate the double-sided tape and disengage the location pins to remove the No. 1 back door emblem.
Be careful not to damage the back door outside garnish.
Remove the protective tape.
75374
4.REMOVE SIDE PANEL EMBLEM
Use the same procedure for the RH side and LH side.
| *a | Wooden Block |
| *b | Piano Wire |
|
Protective Tape |
Apply protective tape around the side panel emblem as shown in the illustration.
Insert a piano wire between the vehicle body and side panel emblem.
Tie objects that can serve as handles (for example, wooden blocks) to both wire ends.
Pull the piano wire and cut the double-sided tape that holds the side panel emblem to the vehicle body to remove the side panel emblem.
Be careful not to damage the vehicle body.
Remove the protective tape.
75443
5.REMOVE NO. 3 BACK DOOR NAME PLATE
| *a | Wooden Block |
| *b | Piano Wire |
|
Protective Tape |
Apply protective tape around the No. 3 back door name plate as shown in the illustration.
Insert a piano wire between the back door outside garnish and No. 3 back door name plate.
Tie objects that can serve as handles (for example, wooden blocks) to both wire ends.
Pull the piano wire and cut the double-sided tape that holds the No. 3 back door name plate to the back door outside garnish to remove the No. 3 back door name plate.
Be careful not to damage the back door outside garnish.
Remove the protective tape.
75310A
6.REMOVE RADIATOR GRILLE EMBLEM ASSEMBLY (for GR SPORT)
| *a | Location Pin |
|
Protective Tape |
Apply protective tape around the radiator grille emblem assembly as shown in the illustration.
Using a moulding remover A, separate the double-sided tape and disengage the location pins to remove the radiator grille emblem assembly.
Be careful not to damage the front bumper assembly.
Remove the protective tape.
75441C
7.REMOVE BACK DOOR NAME PLATE (for GR SPORT)
| *a | Wooden Block |
| *b | Piano Wire |
|
Protective Tape |
Apply protective tape around the back door name plate as shown in the illustration.
Insert a piano wire between the vehicle body and back door name plate.
Tie objects that can serve as handles (for example, wooden blocks) to both wire ends.
Pull the piano wire and cut the double-sided tape that holds the back door name plate to the vehicle body to remove the back door name plate.
Be careful not to damage the vehicle body.
Remove the protective tape.
75365
8.REMOVE FRONT FENDER EMBLEM (for GR SPORT)
Use the same procedure for the RH side and LH side.
| *a | Wooden Block |
| *b | Piano Wire |
|
Protective Tape |
Apply protective tape around the front fender emblem as shown in the illustration.
Insert a piano wire between the vehicle body and front fender emblem.
Tie objects that can serve as handles (for example, wooden blocks) to both wire ends.
Pull the piano wire and cut the double-sided tape that holds the front fender emblem to the vehicle body to remove the front fender emblem.
Be careful not to damage the vehicle body.
Remove the protective tape.