Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › FRONT BUMPER (except GR SPORT) › 2020.08–2020.12
RM32K0E _59 Vehicle Exterior _061792 EXTERIOR PANELS / TRIM _0440078 FRONT BUMPER(except GR SPORT) A

EXTERIOR PANELS / TRIM  FRONT BUMPER(except GR SPORT)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during the front bumper assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Front bumper assembly
·

Measurement of ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


·

Parking support brake system

·

Simple intelligent parking assist system


(Click here)
Front television camera view adjustment Panoramic view monitor system (Click here)

PROCEDURE

Hide 53141F 1.REMOVE RADIATOR COVER

a.

for 2ZR-FXE:

i.
B557783

Remove the 5 clips and 2 hood bumper cushions.



b.

for M20A-FXS:

i.
B557720

Remove the 4 clips and 2 hood bumper cushions.



c.
B557721C02
0,0 0,0 false
V113147

Remove in this Direction


Disengage the claws and guides to remove the radiator cover as shown in the illustration.


Hide 75602A 2.SEPARATE FRONT FENDER MOULDING SUB-ASSEMBLY LH

a.
B482753C01
0,0 0,0 false
V100155

Protective Tape


Apply protective tape around the front fender moulding sub-assembly LH.


b.

Remove the 3 screws.


c.

Remove the 2 clips.


d.
B473971C01
2.844,0.635 3.052,0.813 0.208,0.177 10 true *a
*a 90 deg


Using a screwdriver, turn the pin 90 degrees and remove the 2 pin hold clips.


e.
B560327C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Pull back the edge of the front fender liner LH and disengage the claws by pushing the area indicated by the arrow in the illustration with a finger.

NOTICE:
·

Do not apply excessive force when pulling back the front fender liner LH.

·

To avoid damaging the claws, do not forcibly pull the front fender moulding sub-assembly LH.




f.

Disengage the clips and disconnect the front fender moulding sub-assembly LH.


Hide 75601A 3.SEPARATE FRONT FENDER MOULDING SUB-ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 4.REMOVE FRONT BUMPER ASSEMBLY

a.
B557722C02
0,0 0,0 false
V100155

Protective Tape


Apply protective tape around the front bumper assembly.

HINT:

Use the same procedure for the RH side and LH side.



b.
B557723

Remove the 3 bolts.


c.
B465603

Remove the 6 screws.


d.
B557724C02
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Disengage the claws as shown in the illustration.

HINT:

Use the same procedure for the RH side and LH side.



e.

w/ Headlight Cleaner System:

i.
B454121

Disconnect the washer hose and drain the washer fluid.

HINT:

Use a container to collect the washer fluid.




f.
B557765C02
1.031,0.188 1.198,0.385 0.167,0.198 12 true B 0.771,1.271 0.938,1.469 0.167,0.198 12 true A

w/ Wire Harness:

i.

Disconnect the connector A.



g.

w/ Toyota Safety Sense:

i.

Disconnect the connector B.



h.
B557726C02
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Disengage the claws to remove the front bumper assembly as shown in the illustration.