Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › from 2020.08
RM32K0E _51 Engine / Hybrid System _061336 CRUISE CONTROL _0304571 DYNAMIC RADAR CRUISE CONTROL SYSTEM U

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  TERMINALS OF ECU  


CHECK HYBRID VEHICLE CONTROL ECU (for 2ZR-FXE)


C297329E14
5.563,1.458 5.885,1.677 0.323,0.219 4.292,1.469 4.615,1.688 0.323,0.219 2.76,1.469 3.083,1.688 0.323,0.219 1.438,1.458 1.76,1.677 0.323,0.219 1.479,1.49 1.76,1.656 0.281,0.167 10 false A49 2.802,1.5 3.083,1.667 0.281,0.167 10 false A48 4.365,1.49 4.865,1.677 0.5,0.188 10 false F2 5.635,1.479 6.042,1.646 0.406,0.167 10 false F3

HINT:

The standard voltage, resistance and waveform between each pair of the hybrid vehicle control ECU terminals is shown in the table below. The appropriate conditions for checking each pair of the terminals is also indicated. The result of checks should be compared with the standard voltage, resistance and waveform for each pair of the terminals as displayed in the Specified Condition column. The illustration above can be used as a reference to identify the hybrid vehicle control ECU terminal locations.


Terminal No. (Symbols) Wiring Color Terminal Description Condition Specified Condition
A49-15 (STP) - F3-4 (E12) SB - W-B Stop light signal Brake pedal depressed 11 to 14 V
Brake pedal released Below 1 V
F2-28 (CCS) - F3-4 (E12) R - W-B Cruise control main switch circuit Cruise control main switch off 10 MΩ or higher
Cruise control main switch on Below 1.5 Ω
+RES switch on 235 to 245 Ω
-SET switch on 617 to 643 Ω
CANCEL switch on 1509 to 1571 Ω
A48-28 (ST1-) - F3-4 (E12) R - W-B Stop light signal Power switch on (IG), brake pedal depressed Below 1 V
Power switch on (IG), brake pedal released 11 to 14 V
F3-4 (E12) - Body ground W-B - Body ground Ground Always Below 1 Ω


CHECK HYBRID VEHICLE CONTROL ECU (for M20A-FXS)


A364981E09
1.083,0.75 1.583,1 0.5,0.25 3.167,0.75 3.667,1 0.5,0.25 5.333,0.75 5.833,1 0.5,0.25 3.26,0.792 3.719,0.99 0.458,0.198 10 false F160 5.427,0.802 5.885,1 0.458,0.198 10 false F161 1.208,0.792 1.667,0.99 0.458,0.198 10 false A97

HINT:

The standard voltage, resistance and waveform between each pair of the hybrid vehicle control ECU terminals is shown in the table below. The appropriate conditions for checking each pair of the terminals is also indicated. The result of checks should be compared with the standard voltage, resistance and waveform for each pair of the terminals as displayed in the Specified Condition column. The illustration above can be used as a reference to identify the hybrid vehicle control ECU terminal locations.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A97-7 (STP) - F160-34 (E12) SB - W-B Stop light switch signal Brake pedal depressed 11 to 14 V
Brake pedal released 0 to 1.5 V
F160-28 (ST1-) - F160-34 (E12) R - W-B Stop light switch signal Power switch on (IG), brake pedal depressed 0 to 1.5 V
Power switch on (IG), brake pedal released 11 to 14 V
F161-14 (CCS) - F160-34 (E12) SB - W-B Cruise control main switch circuit Cruise control main switch off 10 MΩ or higher
Cruise control main switch on Below 1.5 Ω
+RES switch ON 235 to 245 Ω
-SET switch ON 617 to 643 Ω
CANCEL switch ON 1509 to 1571 Ω
F160-34 (E12) - Body ground W-B - Body ground Ground Always Below 1 Ω


CHECK MILLIMETER WAVE RADAR SENSOR ASSEMBLY


NOTICE:
·

Turning the power switch on (IG) with connectors disconnected may cause DTCs to be stored. Make sure to clear the DTCs after inspection has been performed.

·

Do not apply excessive force to the millimeter wave radar sensor assembly connector.



A402620E30
3.365,0.063 3.792,0.302 0.427,0.24 3.49,0.094 3.948,0.292 0.458,0.198 10 false A2

a.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A2-8 (IGB) - A2-1 (SGND) B - W-B Power source Power switch on (IG) 11 to 14 V
Power switch off Below 1 V
A2-1 (SGND) - Body ground W-B - Body ground Ground Always Below 1 Ω



CHECK FORWARD RECOGNITION CAMERA


NOTICE:
·

Turning the power switch on (IG) with connectors disconnected may cause DTCs to be stored. Make sure to clear the DTCs after inspection has been performed.

·

Do not apply excessive force to the forward recognition camera connector.



B472992E30
2.073,0.833 2.458,1.042 0.385,0.208 2.188,0.844 2.5,1.042 0.313,0.198 10 false R5

a.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
R5-3 (LKSW) - R5-10 (GND) SB - W-B*1
R - W-B*2
Steering pad switch assembly signal (distance control signal) Power switch on (IG), steering pad switch assembly (vehicle-to-vehicle distance control switch) on Below 1 V
Power switch on (IG), steering pad switch assembly (vehicle-to-vehicle distance control switch) off 4.75 to 5.25 V
R5-8 (BZ) - R5-10 (GND) P - W-B*1
B - W-B*2
Pre-collision city buzzer output Power switch on (IG), buzzer not sounding 11 to 14 V
Power switch on (IG), buzzer sounding Below 1 V
R5-10 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
R5-7 (IGB) - R5-10 (GND) B - W-B Power source Power switch on (IG) 11 to 14 V
Power switch off Below 1 V

*1: for TMC Made

*2: for TMMT Made