Home › Engine / Hybrid System › CRUISE CONTROL › FRONT CAMERA SYSTEM › from 2020.08
RM32K0E _51 Engine / Hybrid System _061336 CRUISE CONTROL _0440928 FRONT CAMERA SYSTEM C

CRUISE CONTROL  FRONT CAMERA SYSTEM  C100A62  Control Module Internal Temperature Sensor A/B Correlation Signal Compare Failure  C1A9304  Main Microcomputer in Front Recognition Camera System Internal Failure  C1A9308  Main Microcomputer in Front Recognition Camera Bus Signal / Message Failure  C1A9444  Image Processing Microcomputer in Front Recognition Camera Data Memory Failure  C1A9445  Image Processing Microcomputer in Front Recognition Camera Program Memory Failure  C1A9447  Image Processing Microcomputer in Front Recognition Camera Watchdog/Safety MCU Failure  C1A9487  Image Processing Microcomputer to Main Microcomputer in Front Recognition Camera Missing Message  C1A9500  Image Processing Module Malfunction in Front Recognition Camera  C1A961C  Power Supply Circuit in Front Recognition Camera Circuit Voltage Out of Range  


DESCRIPTION

When an internal malfunction is detected in the forward recognition camera, these DTCs are stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
C100A62 Control Module Internal Temperature Sensor A/B Correlation Signal Compare Failure A forward recognition camera internal malfunction is detected. Forward recognition camera
C1A9304 Main Microcomputer in Front Recognition Camera System Internal Failure A forward recognition camera internal malfunction is detected. Forward recognition camera
C1A9308 Main Microcomputer in Front Recognition Camera Bus Signal / Message Failure A forward recognition camera internal malfunction is detected. Forward recognition camera
C1A9444 Image Processing Microcomputer in Front Recognition Camera Data Memory Failure A forward recognition camera internal malfunction is detected. Forward recognition camera
C1A9445 Image Processing Microcomputer in Front Recognition Camera Program Memory Failure A forward recognition camera internal malfunction is detected. Forward recognition camera
C1A9447 Image Processing Microcomputer in Front Recognition Camera Watchdog/Safety MCU Failure A forward recognition camera internal malfunction is detected. Forward recognition camera
C1A9487 Image Processing Microcomputer to Main Microcomputer in Front Recognition Camera Missing Message A forward recognition camera internal malfunction is detected. Forward recognition camera
C1A9500 Image Processing Module Malfunction in Front Recognition Camera A forward recognition camera internal malfunction is detected. Forward recognition camera
C1A961C Power Supply Circuit in Front Recognition Camera Circuit Voltage Out of Range A forward recognition camera internal malfunction is detected. Forward recognition camera

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle and a DTC may be stored.

·

When the forward recognition camera is replaced with a new one or the windshield glass is replaced or removed/installed, make sure to read Before Starting Adjustment, then perform optical axis alignment for the forward recognition camera and clear the vehicle control history for each system.

HINT:

Forward recognition camera axis alignment can be performed by using either One Time Recognition, Sequential Recognition or Driving Adjustment.

One Time Recognition: Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>TARGET ADJUSTMENT(ONE TIME RECOGNITION)

Sequential Recognition: Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>TARGET ADJUSTMENT(SEQUENTIAL RECOGNITION)

Driving Adjustment: Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>DRIVING ADJUSTMENT




PROCEDURE

1.CHECK FOR DTCs
a.

Turn the power switch off.


b.

Turn the power switch on (IG) and wait 80 seconds or more.


c.

Check for DTCs.

Chassis > Front Recognition Camera > Trouble Codes
50001 430

Result:
Result Proceed to
DTC C100A62, C1A9304, C1A9308, C1A9444, C1A9445, C1A9447, C1A9487, C1A9500 and C1A961C are not output A
DTC C100A62, C1A9304, C1A9308, C1A9444, C1A9445, C1A9447, C1A9487, C1A9500 or C1A961C is output B



A

B

2.REPLACE FORWARD RECOGNITION CAMERA
2.REPLACE FORWARD RECOGNITION CAMERA
a.

Replace the forward recognition camera.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>REMOVAL


b.

Perform forward recognition camera adjustment.

HINT:

Forward recognition camera axis alignment can be performed by using either One Time Recognition, Sequential Recognition or Driving Adjustment.

One Time Recognition: Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>TARGET ADJUSTMENT(ONE TIME RECOGNITION)

Sequential Recognition: Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>TARGET ADJUSTMENT(SEQUENTIAL RECOGNITION)

Driving Adjustment: Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>DRIVING ADJUSTMENT



Result:
Proceed to
NEXT



NEXT

END