Home › Engine / Hybrid System › CRUISE CONTROL › LANE TRACING ASSIST SYSTEM › from 2020.08
RM32K0E _51 Engine / Hybrid System _061336 CRUISE CONTROL _0440929 LANE TRACING ASSIST SYSTEM J

CRUISE CONTROL  LANE TRACING ASSIST SYSTEM  Steering Pad Switch Circuit  


DESCRIPTION

The forward recognition camera receives LTA main switch signals from the steering pad switch assembly.

WIRING DIAGRAM

A406735E64
1.417,1.281 2.625,1.531 1.208,0.25 10 false LTA Main Switch 1.042,2.302 3.188,2.563 2.146,0.26 10 false Steering Pad Switch Assembly 2.896,1.594 4.677,1.865 1.781,0.271 10 false Spiral Cable Sub-assembly 4.906,1.031 6.896,1.219 1.99,0.188 10 false Forward Recognition Camera 4.042,0.49 4.5,0.688 0.458,0.198 10 false F29 4.042,1.104 4.5,1.302 0.458,0.198 10 false F29 2.906,0.5 3.365,0.698 0.458,0.198 10 false z1 2.906,1.115 3.365,1.313 0.458,0.198 10 false z1 3.427,0.406 4.042,0.604 0.615,0.198 10 false DIST 3.417,1.01 4.031,1.208 0.615,0.198 10 false ECC 4.906,0.844 5.292,1.063 0.385,0.219 10 false R5 5.375,0.521 5.875,0.719 0.5,0.198 10 false LKSW 5.198,0.406 5.51,0.604 0.313,0.198 10 false 3 4.063,0.302 4.375,0.5 0.313,0.198 10 false 12 4.125,0.906 4.438,1.104 0.313,0.198 10 false 2 2.938,0.906 3.25,1.104 0.313,0.198 10 false 7 2.938,0.302 3.25,0.5 0.313,0.198 10 false 4 2.323,0.344 2.719,0.531 0.396,0.188 10 false DIST 2.333,0.938 2.76,1.146 0.427,0.208 10 false ECC

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle and a DTC may be stored.

·

When the forward recognition camera is replaced with a new one or the windshield glass is replaced or removed/installed, make sure to read Before Starting Adjustment, then perform optical axis alignment for the forward recognition camera and clear the vehicle control history for each system.

HINT:

Forward recognition camera axis alignment can be performed by using either One Time Recognition, Sequential Recognition or Driving Adjustment.

One time recognition: Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>TARGET ADJUSTMENT(ONE TIME RECOGNITION)

Sequential recognition: Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>TARGET ADJUSTMENT(SEQUENTIAL RECOGNITION)

Driving Adjustment: Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>DRIVING ADJUSTMENT


·

During the steering pad switch assembly check, check the precautions for the airbag system since the horn button assembly is removed during servicing. (installation/removal of parts, checks, replacement, etc.)

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION



PROCEDURE

1.READ VALUE USING GTS (LDA CONTROL)
a.

Read the Data List according to the display on the GTS.

Chassis > Lane Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
LDA Control Whether lane tracing assist system control is permitted or not Prohibit or Permit Prohibit: Lane tracing assist system control not possible
Permit: Lane tracing assist system control possible
-
Chassis > Lane Control > Data List
Tester Display
LDA Control
50003 418 3

Result:
Result Proceed to
Data List value changes when LTA Main Switch is operated A
Data List value does not change when LTA Main Switch is operated B



A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

2.INSPECT STEERING PAD SWITCH ASSEMBLY
2.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

Remove the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>REMOVAL


b.

Inspect the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

3.INSPECT SPIRAL CABLE SUB-ASSEMBLY
a.

Remove the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL


b.

Inspect the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSTALLATION


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - FORWARD RECOGNITION CAMERA)

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - FORWARD RECOGNITION CAMERA)
a.

Disconnect the F29 spiral cable sub-assembly connector.


b.

Disconnect the R5 forward recognition camera connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F29-12 (DIST) - R5-3 (LKSW) Always Below 1 Ω
F29-12 (DIST) or R5-3 (LKSW) - Body ground Always 10 kΩ or higher



d.

Connect the R5 forward recognition camera connector.


e.

Connect the F29 spiral cable sub-assembly connector.


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - BODY GROUND)
a.

Disconnect the F29 spiral cable sub-assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F29-2 (ECC) - Body ground Always Below 1 Ω



c.

Connect the F29 spiral cable sub-assembly connector.


Result:
Proceed to
OK
NG



OK

REPLACE FORWARD RECOGNITION CAMERA

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR