Vehicle control history may be recorded due to the replacement or repair of related parts.
CHECK VEHICLE CONTROL HISTORY (FRONT RADAR SENSOR SYSTEM)
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Front Radar Sensor / Utility / Vehicle Control History (RoB).
| Tester Display |
|---|
| Vehicle Control History (RoB) |
| Multi-information Display | Code | Tester Display | Description | Diagnostic Note |
|---|---|---|---|---|
| Pre-Collision System Malfunction Visit Your Dealer | X2023 | Front Radar Sensor Optical Axis Not Adjusted | History of millimeter wave radar sensor assembly beam axis not being adjusted. | 1.
2.
If the value of "Optical Axis Not Adjusted Status" is Not Complete, perform beam axis alignment of the millimeter wave radar sensor assembly.
|
| Pre-Collision System Radar In Self Calibration Unavailable See Owner's Manual | X2024 | Front Radar Sensor Temporary Unavailable (Vertical Direction Optical Axis Misalignment) | History of millimeter wave radar sensor assembly beam axis misalignment (vertical). | 1.
Perform millimeter wave radar sensor assembly beam axis alignment.
2.
Turn the power switch off. 3.
Turn the power switch on (IG). 4.
Check that "Pre-Collision System Radar In Self Calibration Unavailable See Owner's Manual" is not displayed on the multi-information display. Cause:
A determination was made that millimeter wave radar sensor assembly vertical axis was misaligned. |
| Pre-Collision System Radar Sensor Blocked Unavailable Clean Radar Sensor | X2026 | Front Radar Sensor Dirt | History of system operation being temporarily suspended due to millimeter wave radar sensor assembly not being able to detect objects. | 1.
Check whether the millimeter wave radar sensor assembly and surrounding area is dirty or obstructed by foreign matter -
A non-genuine millimeter wave sensor cover is installed -
There is dirt on the radar, the radar sensor cover or the surrounding area -
An accessory, such as bull bars, a grille guard, etc., which interferes with millimeter radio waves is installed -
The sensor cover or its surrounding area has been painted or has a sticker attached -
There is foreign matter between the radar and radar sensor cover 2.
Clean away any dirt or foreign matter that is adhering to the area around the millimeter wave radar sensor assembly. 3.
Turn the power switch off. 4.
Start the hybrid system and drive the vehicle for 5 minutes or more. 5.
Check whether "Pre-Collision System Radar Sensor Blocked Unavailable Clean Radar Sensor" is displayed on the multi-information display. 6.
If the message is still displayed, perform beam axis alignment of the millimeter wave radar sensor assembly.
Cause:
The millimeter wave radar sensor assembly is dirty or obstructed by foreign matter. |
| Pre-Collision System Out of Temperature Range Unavailable See Owner's Manual | X2027 | Front Radar Sensor Outside Guaranteed Operating Temperature | History of system operation being temporarily suspended due to the millimeter wave radar sensor assembly being excessively hot or cold. | 1.
2.
If the value of "Millimeter-wave Circuit Temperature Protection" is ON, warm or cool the area around the millimeter wave radar sensor assembly. Cause:
The following millimeter wave radar sensor assembly conditions are met: -
After being subjected to an extremely cold environment, the area around the millimeter wave radar sensor assembly is -30°C (-22°F) or less. -
After being subjected to an extremely hot environment, the area around the millimeter wave radar sensor assembly is 70°C (158°F) or more. |
| Pre-Collision System Unavailable See Owner's Manual | X2028 | Front Radar Sensor Outside Guaranteed Operating Voltage | History of system operation being temporarily suspended due to millimeter wave radar sensor assembly power source voltage being excessively high or low. | Cause:
The following millimeter wave radar sensor assembly conditions are met: -
The input voltage decreases to approximately 8 V or less directly after the hybrid system starts. -
The input voltage increases to approximately 16 V or more directly after the hybrid system starts. |
| Pre-Collision System Unavailable See Owner's Manual | X202B | Front Radar Sensor Temporary Unavailable (Radio Wave Interference) | Stored when determination made for temporary suspension of system operation due to millimeter wave radar sensor assembly detecting interference from other nearby radar emitters. | Move the vehicle to a different location until "Pre-Collision System Unavailable See Owner's Manual" disappears from the multi-information display.
Cause:
Determination was made for temporary suspension of system operation due to millimeter wave radar sensor assembly detecting interference from other nearby radar emitters.
|
CLEAR VEHICLE CONTROL HISTORY (FRONT RADAR SENSOR SYSTEM)
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Front Radar Sensor / Utility / Vehicle Control History (RoB).
| Tester Display |
|---|
| Vehicle Control History (RoB) |
According to the display on the GTS, clear the Vehicle Control History (RoB).
By performing this procedure, all stored Vehicle Control History will be cleared.
CHECK VEHICLE CONTROL HISTORY (AIRBAG SYSTEM)
A part of the control history can be confirmed using the Vehicle Control History.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>VEHICLE CONTROL HISTORY