Home › Vehicle Exterior › ACOUSTIC VEHICLE ALERTING SYSTEM › ACOUSTIC VEHICLE ALERTING SYSTEM › from 2020.08
RM32K0E _59 Vehicle Exterior _094426 ACOUSTIC VEHICLE ALERTING SYSTEM _0444527 ACOUSTIC VEHICLE ALERTING SYSTEM J

ACOUSTIC VEHICLE ALERTING SYSTEM  ACOUSTIC VEHICLE ALERTING SYSTEM  There is No Sound Made  


DESCRIPTION

Based on signals received from each ECU, the vehicle approaching speaker controller outputs warning sounds through the vehicle approaching speaker assembly.

WIRING DIAGRAM

E445909E22
5.594,5.75 6.885,6.26 1.292,0.51 10 false Vehicle Approaching Speaker Assembly 4.5,4.948 4.958,5.146 0.458,0.198 10 false SP+ 6.177,5.229 6.635,5.427 0.458,0.198 10 false - 4.469,6.969 4.927,7.167 0.458,0.198 10 false GND 3.531,7.781 4.813,8.229 1.281,0.448 10 false Vehicle Approaching Speaker Controller 0.781,7.469 2.615,7.969 1.833,0.5 10 false Combination Meter Assembly (Meter Circuit Plate) 0.802,2.365 2.583,2.708 1.781,0.344 10 false Hybrid Vehicle Control ECU 0.844,4.052 2.5,4.542 1.656,0.49 10 false Main Body ECU (Multiplex Network Body ECU) 0.688,5.75 2.74,6.333 2.052,0.583 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 1.938,0.896 3,1.135 1.063,0.24 10 false ECU-IG1 NO. 3 0.458,0.719 1.844,0.969 1.385,0.25 10 false from IG Circuit 3.573,0.74 4.031,0.938 0.458,0.198 10 false IG 1.479,8.417 3.333,8.635 1.854,0.219 10 false : CAN Communication Line 3.365,0.625 3.823,0.823 0.458,0.198 10 false 1 3.521,7.615 3.938,7.823 0.417,0.208 10 false F172 4.854,4.854 5.271,5.063 0.417,0.208 10 false 7 4.854,5.156 5.271,5.365 0.417,0.208 10 false 8 4.844,6.844 5.26,7.052 0.417,0.208 10 false 6 5.594,5.583 6.01,5.792 0.417,0.208 10 false A14 6.01,4.854 6.427,5.063 0.417,0.208 10 false 2 6.01,5.135 6.427,5.344 0.417,0.208 10 false 1 6.156,4.948 6.615,5.146 0.458,0.198 10 false + 4.521,5.25 4.979,5.448 0.458,0.198 10 false SP-

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

The acoustic vehicle alerting system uses the CAN communication system. Inspect the communication functions by following How to Proceed with Troubleshooting.

Click hereVehicle Exterior>ACOUSTIC VEHICLE ALERTING SYSTEM>ACOUSTIC VEHICLE ALERTING SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.CHECK FOR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Vehicle Proximity Notification System / Trouble Codes.

Body Electrical > Vehicle Proximity Notification System > Trouble Codes
50001 393

e.

Check for DTCs.


Result:
Result Proceed to
DTC B1350 is not output A
DTC B1350 is output B



A

2.PERFORM ACTIVE TEST USING GTS

B

2.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Vehicle Proximity Notification System / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Vehicle Proximity Notification System > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Proximity Sound (Vehicle Stationary) 0 km/h (0 mph) vehicle proximity warning sound OFF or ON -
Body Electrical > Vehicle Proximity Notification System > Active Test
Tester Display
Proximity Sound (Vehicle Stationary)
50004 393 2

Result:
Result Proceed to
The warning sound is produced A
The warning sound is not produced B



A

B

3.CHECK HARNESS AND CONNECTOR (VEHICLE APPROACHING SPEAKER CONTROLLER - POWER SOURCE AND BODY GROUND)
3.CHECK HARNESS AND CONNECTOR (VEHICLE APPROACHING SPEAKER CONTROLLER - POWER SOURCE AND BODY GROUND)
a.

Disconnect the F172 vehicle approaching speaker controller connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F172-1 (IG) - Body ground Power switch on (IG) 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F172-6 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR