Home › Vehicle Interior › PRE-COLLISION › PRE-COLLISION SYSTEM › from 2020.08
RM32K0E _58 Vehicle Interior _061839 PRE-COLLISION _0303861 PRE-COLLISION SYSTEM U

PRE-COLLISION  PRE-COLLISION SYSTEM  FAIL-SAFE CHART  


FAIL-SAFE FUNCTION


a.

When a malfunction occurs in the pre-collision system, a message will be displayed on the multi-information display and the pre-collision system will be disabled depending on the malfunction.

Warning Message Cause DTC/RoB No. Conditions to Return to Normal
"Pre-Collision System Malfunction Visit Your Dealer" Pre-collision system malfunction C142571 The power switch is turned on (IG) after an abnormal stop light relay signal is no longer received from the skid control ECU (brake booster with master cylinder assembly).
U012587 Communication with the yaw rate sensor (airbag sensor assembly) has returned to normal.
U012687 Communication with the steering sensor returns to normal.
U012987 Communication with the skid control ECU (brake booster with master cylinder assembly) returns to normal.
U015587 Communication with the combination meter assembly returns to normal.
U023587 When entering test mode, the skid control ECU (brake booster with master cylinder assembly) has determined that the pre-collision system is installed in the vehicle.
U023A87 Communication with the forward recognition camera returns to normal.
U029387 Communication with the hybrid vehicle control ECU returns to normal.
U030051 3 seconds or more elapse after the vehicle information of the millimeter wave radar sensor assembly is acquired from the hybrid vehicle control ECU.
U030057 The vehicle information stored in the millimeter wave radar sensor assembly and the vehicle information sent from the hybrid vehicle control ECU match.
U041881 The power switch is turned on (IG) after a signal indicating a brake system malfunction is no longer received from the skid control ECU (brake booster with master cylinder assembly).
"Pre-Collision System Malfunction Visit Your Dealer" Pre-collision system malfunction X2000 The power switch is turned on (IG) after a signal indicating a malfunction of the skid control ECU (brake booster with master cylinder assembly) or yaw rate sensor (airbag sensor assembly) is no longer received.
X2001 The power switch is turned on (IG) after a signal indicating a malfunction of the steering sensor is no longer received from the steering angle sensor.
X2002 A hybrid control system malfunction signal is no longer received from the hybrid vehicle control ECU.
X2003 A signal indicating an electronically controlled brake system malfunction is no longer received from the skid control ECU (brake booster with master cylinder assembly).
X2006 The buzzer malfunction is no longer detected.
X2012 The power switch is turned on (IG) after it is determined that the forward recognition camera is no longer malfunctioning.
X2013 The power switch is turned on (IG) after it is determined that the optical axis of the forward recognition camera is no longer misaligned.
X2014 It is determined that the forward recognition camera optical axis is calibrated.
X2018 The power switch is turned on (IG) after it is determined that the heater of the forward recognition camera is no longer malfunctioning.
X2020 The system stops receiving destination malfunction signals from the millimeter wave radar sensor assembly.
X2021 The power switch is turned on (IG) after a signal from the millimeter wave radar sensor assembly indicating a malfunction is no longer received.
X2022 The power switch is turned on (IG) after a signal from the millimeter wave radar sensor assembly indicating beam axis misalignment is no longer received.
"Pre-Collision System Malfunction Visit Your Dealer" Pre-collision system malfunction X2023 A signal from the millimeter wave radar sensor assembly indicating that beam axis has not been calibrated is no longer received.
X202A The destination not programmed signal is no longer received from the millimeter wave radar sensor assembly.
X203E The signal indicating communication malfunction with the power steering ECU assembly is no longer received.
X2074 The signal from the power steering ECU assembly indicating communication malfunction with the millimeter wave radar sensor assembly is no longer received.
X2081 After the power switch is turned from off to on (IG), the signal indicating power steering system steering assist unavailable is no longer received from the power steering ECU assembly.
X2082 After the power switch is turned from off to on (IG), the signal indicating steering assist angle malfunction is no longer received from the power steering ECU assembly.
"Pre-Collision System Radar In Self Calibration Unavailable See Owner's Manual" Millimeter wave radar sensor vertical axis misalignment X2024 Millimeter wave radar sensor beam axis adjustment is completed and beam axis learning is completed
"Pre-Collision System Radar Sensor Blocked Unavailable Clean Radar Sensor" Foreign matter attached to millimeter wave radar sensor assembly X2026 Millimeter wave radar sensor assembly is cleaned
"Pre-Collision System Out of Temperature Range Unavailable See Owner's Manual" Millimeter wave radar sensor assembly temperature malfunction X2027 Millimeter wave radar sensor temperature returns to normal
"Pre-Collision System Unavailable See Owner's Manual" Millimeter wave radar sensor assembly low voltage malfunction X2028 Millimeter wave radar sensor voltage returns to normal
Front Radar Sensor Temporary Unavailable (Radio Wave Interference) X202B The vehicle is moved to a location without radio frequency interference.
HINT:

If the system does not return to normal even after moving the vehicle to a different location, there may be a problem with the steering center position. Inspect the steering system components for incorrect installation, deformation, or damage, and perform calibration or replace components as necessary.


"Front Camera Low Visibility Unavailable See Owner's Manual" Forward recognition camera or area of the windshield in front of the camera is dirty or fogged up X2015 Forward recognition camera or area of windshield glass in front of forward recognition camera is cleaned or defogged
"Front Camera Out of Temperature Range Unavailable Wait until Normal Temperature" Forward recognition camera temperature outside of operational range X2016 Forward recognition camera temperature returns to normal
"Front Camera Unavailable See Owner's Manual" Forward recognition camera voltage outside of operational range X2017 Forward recognition camera voltage returns to normal