Home › Vehicle Interior › PRE-COLLISION › PRE-COLLISION SYSTEM › from 2020.08
RM32K0E _58 Vehicle Interior _061839 PRE-COLLISION _0303861 PRE-COLLISION SYSTEM U

PRE-COLLISION  PRE-COLLISION SYSTEM  DATA LIST / ACTIVE TEST  


DATA LIST


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

Data List values may experience significant variations due to small differences in measurement, different measurement environments, changes in the vehicle over time, etc., making it difficult to display a clear standard value for judgment. Due to this, it is possible that malfunctions could exist even when values are within the specified ranges.


a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Pre-Collision System / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Pre-Collision System > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Total Distance Traveled - - - Cannot be used
Total Distance Traveled - Unit - - - Cannot be used
PCS Function ON/OFF State Status of the pre-collision system OFF switch ON / OFF ON: Pre-collision system enabled
OFF: Pre-collision system disabled
-
PBA Request Pre-collision brake assist operation status (While a control command is present, assist control operates when the driver depresses the brake pedal.) Not PBA Request / PBA Standby Request / PBA Request Level 1 / PBA Request Level 2 Not PBA Request: Pre-collision brake assist not requested
PBA Standby Request: Low pre-collision brake assist requested
PBA Request Level 1: Medium pre-collision brake assist requested
PBA Request Level 2: High pre-collision brake assist requested
The value changes in accordance with the possibility of a collision. This item indicates the pre-collision brake assist standby status. Whether pre-collision brake assist is applied or not is determined by the depression of the brake pedal.
VGRS Activation Request VGRS control activation start Not Request / VGRS 1 Request / VGRS 2 Request / VGRS 3 Request Not Request:
VGRS 1 Request: Request 1
VGRS 2 Request: Request 2
VGRS 3 Request: Request 3
This item is displayed on the GTS for vehicles without the VGRS system, but cannot be used
Warning Brake Request Warning brake operational status ON / OFF ON: Operating
OFF: Not operating
-
FPB Request Skid control ECU (brake booster with master cylinder assembly) PCS brake request (pre-braking) ON / OFF ON: Operating
OFF: Not operating
-
PB Request Pre-collision brake request status ON / OFF ON: Operating
OFF: Not operating
-
AVS Control Request AVS control activation status ON / OFF ON: AVS control activated
OFF: AVS control not activated
This item is displayed on the GTS for vehicles without AVS, but cannot be used
Prefill Skid control ECU (brake booster with master cylinder assembly) PCS brake assist standby ON / OFF ON: Operating
OFF: Not operating
-
PBR Request PBR operation status ON / OFF ON: Operating
OFF: Not operating
-
PBH Request PBH operation status ON / OFF ON: Operating
OFF: Not operating
-
LPB Request LPB operation status ON / OFF ON: Operating
OFF: Not operating
-
PCS PBA Invalid Pre-collision brake assist function status ON / OFF ON: Pre-collision brake assist function invalid
OFF: Pre-collision brake assist function valid
-
PCS Warning Buzzer Invalid PCS warning buzzer status ON / OFF ON: PCS warning buzzer function invalid
OFF: PCS warning buzzer function valid
-
PCS PB Invalid PCS brake function status ON / OFF ON: PCS brake function invalid
OFF: PCS brake function valid
-
Acceleration Suppression at Low Speed (A Control) Invalid Acceleration suppression at low speed (A control) invalid status ON / OFF ON: Acceleration suppression at low speed (A control) function invalid
OFF: Acceleration suppression at low speed (A control) function valid
Cannot be used
Emergency Steering Assist Invalid 1 Emergency Steering Assist Invalid 1 status ON / OFF ON: Emergency steering assist invalid 1 function invalid
OFF: Emergency steering assist invalid 1 function valid
w/ Emergency steering assist
Emergency Steering Assist Invalid 2 Emergency Steering Assist Invalid 2 status ON / OFF ON: Emergency steering assist invalid 2 function invalid
OFF: Emergency steering assist invalid 2 function valid
w/ Emergency steering assist
PCS Warning Display Request PCS warning message status Not Request / PCS Warning Display 1 Request / PCS Warning Display 2 Request / PCS Warning Display 3 Request Not Request: Not displayed
PCS Warning Display 1 Request: Displayed
PCS Warning Display 2 Request: Not used
PCS Warning Display 3 Request: Not used
"BRAKE!" is displayed on multi-information display
PCS Warning Buzzer Request Pre-collision city buzzer operation status ON / OFF ON: Sounding
OFF: Not sounding
-
Vehicle Information (Conv/HV/EV) Vehicle information (Conv/HV/EV) Unknown / Conv / HV/EV Unknown: Vehicle information not confirmed
Conv: Conventional
HV/EV: Hybrid vehicle
-
Vehicle Information (Powertrain Type) Vehicle information (powertrain type) Unknown / Conv / S&S / HV / PHV / EV / 1Motor HV / FCV Displays the type of powertrain -
Vehicle Information (Transmission Type) Vehicle information (transmission type) MT / AT / CVT / MMT / SMT / HV/EV - AT / Unknown Displays the type of transmission -
PCS Function ON/OFF State Stored Pre-collision system on/off setting when the pre-collision system is turned off and the power switch is turned off and then to on (IG). Stored / Not Stored Stored: PCS function remains OFF
Not Stored: PCS function resets to ON
"PCS Function ON/OFF State Stored" is a customizable item which can be set using the GTS.
PCS Warning Timing State Stored 2 Sensitivity setting when the pre-collision system is turned on and the power switch is turned off and then to on (IG). Stored / Not Stored Stored: Warning sensitivity is maintained at the previous value
Not Stored: Warning sensitivity resets to "Mid"
"PCS Warning Timing State Stored 2" is a customizable item which can be set using the GTS.
PCS Warning Timing State Stored 3 Sensitivity setting when the pre-collision system is turned off and the power switch is turned off and then to on (IG). Stored / Not Stored Stored: Warning sensitivity is maintained at the previous value
Not Stored: Warning sensitivity resets to "Mid"
"PCS Warning Timing State Stored 3" is a customizable item which can be set using the GTS.
PCS Warning Timing State Stored 1 Sensitivity setting of the pre-collision system when the pre-collision system is turned off and the then on with the power switch on (IG). Stored / Not Stored Stored: Warning sensitivity is maintained at the previous value
Not Stored: Warning sensitivity resets to "Mid"
"PCS Warning Timing State Stored 1" is a customizable item which can be set using the GTS.


ACTIVE TEST


HINT:

Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Pre-Collision System / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Pre-Collision System > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
PCS Warning Buzzer Sounds the pre-collision city buzzer Start / Stop Test possible with power switch on (IG), vehicle stopped