Home › Engine / Hybrid System › M20A-FXS (ENGINE CONTROL) › MASS AIR FLOW METER › from 2020.08
RM32K0E _51 Engine / Hybrid System _083960 M20A-FXS ENGINE CONTROL _0404837 MASS AIR FLOW METER G

M20A-FXS ENGINE CONTROL  MASS AIR FLOW METER  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 22204 1.INSPECT MASS AIR FLOW METER SUB-ASSEMBLY

HINT:

Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly.

Click hereEngine / Hybrid System>M20A-FXS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


a.

Read the value of Data List item "Mass Air Flow Sensor" using the GTS.

NOTICE:

Perform the inspection of the mass air flow meter sub-assembly while it is installed to the air cleaner cap sub-assembly (installed to the vehicle).


i.

Connect the GTS to the DLC3.


ii.

Turn the power switch on (IG).


iii.

Turn the GTS on.


iv.

Put the engine in Inspection Mode (Maintenance Mode).

Powertrain > Hybrid Control > Utility
Tester Display
Inspection Mode
50005 397 2103

v.

Start the engine.


vi.

Enter the following menus: Powertrain / Engine / Data List / Mass Air Flow Sensor.

Powertrain > Engine > Data List
Tester Display
Mass Air Flow Sensor
50003 372 215

vii.

According to the display on the GTS, read the Data List when the engine is running.

Standard Condition:
GTS Display Condition Specified Condition
Mass Air Flow Sensor Idling (shift lever in P, engine warmed up, inspection mode [maintenance mode] and not charge control) 2.0 to 8.6 gm/sec
2500 rpm (shift lever in P, engine warmed up and inspection mode [maintenance mode] ) 5.5 to 18.6 gm/sec


If the result is not as specified, replace the mass air flow meter sub-assembly.

If the result is within the specified range, remove and inspect the mass air flow meter sub-assembly.

Click hereEngine / Hybrid System>M20A-FXS (ENGINE CONTROL)>MASS AIR FLOW METER>INSPECTION



Hide 22204 2.CLEAN MASS AIR FLOW METER SUB-ASSEMBLY

NOTICE:

If the mass air flow meter sub-assembly is removed and installed 10 times or more, the thread of the hole of the mass air flow meter sub-assembly may be damaged. Therefore, do not loosen the screws of the mass air flow meter sub-assembly.


a.

Remove the air cleaner cap sub-assembly.


b.
A489843C01
0.938,2.771 1.573,2.771 true 1.854,1.906 2.323,1.906 true 1.104,1.052 1.573,1.052 true 2.344,1.823 2.573,1.99 0.229,0.167 10 true *1 0.729,2.708 0.948,2.875 0.219,0.167 10 true *a 2.198,4.438 2.417,4.625 0.219,0.188 10 false *b 1.615,0.979 1.865,1.146 0.25,0.167 10 true *c
*1 Mass Air Flow Meter Sub-assembly
*a Air Blow Gun
*b 10 mm (0.394 in.)
*c Airflow Hole


Clean the mass air flow meter sub-assembly.

NOTICE:
·

Do not contact the mass air flow meter sub-assembly with the nozzle of the air blow gun.

·

Do not insert the nozzle of the air blow gun into the airflow hole.



i.
A398469C01
0.125,0.125 0.365,0.302 0.24,0.177 10 false *a 1.313,0.24 1.552,0.406 0.24,0.167 10 false *b 1.563,0.573 1.792,0.74 0.229,0.167 10 false *c 0.688,0.906 0.927,1.083 0.24,0.177 10 false *d 0.677,1.708 0.917,1.885 0.24,0.177 10 false *e
*a Air Blow Duration
*b 3 to 6 Seconds
*c 1 Second
*d Air Blowing
*e Air Stopped


Using an air blow gun, clean the hole of the mass air flow meter sub-assembly by applying approximately 10 intermittent bursts of air to the airflow hole at a pressure of approximately 392 to 981 kPa (4.0 to 10.0 kgf/cm2, 57 to 142 psi).



c.

Install the air cleaner cap sub-assembly.


Hide 3.PERFORM INITIALIZATION

a.

Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly.

Click hereEngine / Hybrid System>M20A-FXS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION