Home › Engine / Hybrid System › 2ZR-FXE (HYBRID / BATTERY CONTROL) › HV BATTERY THERMISTOR (for NICKEL METAL HYDRIDE BATTERY) › from 2020.08
RM32K0E _51 Engine / Hybrid System _083958 2ZR-FXE HYBRID / BATTERY CONTROL _0404379 HV BATTERY THERMISTOR(for NICKEL METAL HYDRIDE BATTERY) A

2ZR-FXE HYBRID / BATTERY CONTROL  HV BATTERY THERMISTOR(for NICKEL METAL HYDRIDE BATTERY)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during hybrid battery thermistor removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedures Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Panoramic view monitor system (Click here)

CAUTION:
·
A340386

This vehicle has contains high voltage circuits standardized with orange colored wiring and connectors, so follow the instructions in this manual to perform the procedures correctly.

Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)>PRECAUTION

·

If the correct procedures are not followed according to the instructions in this manual, there is a danger of electric shock from the high voltage circuits.

·
A340358

Be sure to wear insulating gloves when working on high voltage wiring or components.

·

If work is performed without wearing insulating gloves, there is a danger of electric shock.



HINT:

When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link

*1: When performing learning using the GTS

Click here(Click here)

Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Simple intelligent parking assist system*1
Parking support brake system*1
Toyota parking assist-sensor system*1

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide G920Q 3.REMOVE NO. 1 HYBRID BATTERY SHIELD SUB-ASSEMBLY

CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.
A375918

Remove the 4 nuts.


b.
A375919C03
0.583,2.646 0.531,2.406 0.531,2.406 0.281,2.406 true 1.479,2.896 1.781,2.896 true 0.094,2.354 0.406,2.552 0.313,0.198 10 false *2 1.854,2.833 2.167,3.031 0.313,0.198 10 false *1
*1 No. 1 Hybrid Battery Shield Sub-assembly
*2 No. 2 Hybrid Battery Shield Sub-assembly
V100135

Pull Back


Pull back the No. 2 hybrid battery shield sub-assembly and remove the No. 1 hybrid battery shield sub-assembly from the HV battery.

HINT:

Pull back the No. 2 hybrid battery shield sub-assembly until it is separated from the stud bolt of the No. 1 hybrid battery shield sub-assembly.



Hide G92D1 4.REMOVE NO. 1 HYBRID BATTERY INTAKE DUCT

CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.
A375920

Disengage the claw of hybrid battery thermistor (sensor portion) and disconnect the hybrid battery thermistor from the No. 1 hybrid battery intake duct.


b.

Disengage the claw to remove the No. 1 hybrid battery intake duct from the HV battery.


Hide G9282 5.REMOVE HYBRID BATTERY THERMISTOR

CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.
A375921

Disengage the clamp.


b.
A375922

Disengage the 2 claws and remove the No. 1 hybrid battery packing from the HV battery.


c.
A375901

Disengage the clamp.


d.

Disconnect the battery voltage sensor connector.


e.
A375923

Disengage the 4 clamps.


f.
A375924

Disengage the 3 claws of the hybrid battery thermistor (sensor portions) and remove the hybrid battery thermistor from the HV battery.