Home › Engine / Hybrid System › M20A-FXS (HYBRID / BATTERY CONTROL) › HV BATTERY THERMISTOR › from 2020.08
RM32K0E _51 Engine / Hybrid System _083959 M20A-FXS HYBRID / BATTERY CONTROL _0404418 HV BATTERY THERMISTOR A

M20A-FXS HYBRID / BATTERY CONTROL  HV BATTERY THERMISTOR  REMOVAL  


CAUTION / NOTICE / HINT

CAUTION:
·
A340386

Orange wire harnesses and connectors indicate high-voltage circuits. To prevent electric shock, always follow the procedure described in the repair manual.

Click hereEngine / Hybrid System>M20A-FXS (HYBRID / BATTERY CONTROL)>HYBRID CONTROL SYSTEM>PRECAUTION

·
A340358

Be sure to wear insulating gloves when working on high voltage wiring or components.

·

If work is performed without wearing insulating gloves, there is a danger of electric shock.



HINT:

When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link

*1: When performing learning using the GTS

Click here(Click here)

Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Simple intelligent parking assist system*1
Parking support brake system*1
Toyota parking assist-sensor system*1

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.REMOVE HV BATTERY JUNCTION BLOCK ASSEMBLY

Hide G920Q 3.REMOVE NO. 1 HYBRID BATTERY SHIELD SUB-ASSEMBLY

CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.
A444040

Remove the 4 nuts.


b.
A444041C01
0.583,2.646 0.531,2.406 0.531,2.406 0.26,2.406 true 1.479,2.896 1.781,2.896 true 0.094,2.313 0.406,2.51 0.313,0.198 10 false *2 1.792,2.802 2.104,3 0.313,0.198 10 false *1
*1 No. 1 Hybrid Battery Shield Sub-assembly
*2 Rear Hybrid Battery Shield Sub-assembly
V113147

Pull Back


Pull back the rear hybrid battery shield sub-assembly and remove the No. 1 hybrid battery shield sub-assembly from the HV battery.

HINT:

Pull back the rear hybrid battery shield sub-assembly until it is separated from the stud bolt of the No. 1 hybrid battery shield sub-assembly.



Hide G92D1 4.REMOVE NO. 1 HYBRID BATTERY INTAKE DUCT

CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.
A444042

Disengage the claw of hybrid battery thermistor (sensor portion) and disconnect the hybrid battery thermistor from the No. 1 HV battery cover intake duct.


b.

Disengage the claw to remove the No. 1 HV battery cover intake duct from the HV battery.


Hide G9282 5.REMOVE HYBRID BATTERY THERMISTOR

CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.
A444043

Disengage the clamp.


b.
A444044

Disengage the clamp.


c.

Disconnect the battery voltage sensor connector.


d.
A444045

Disengage the 4 clamps.


e.
A444046

Disengage the 3 claws of the hybrid battery thermistor (sensor portions) and remove the hybrid battery thermistor from the HV battery.