Home › Engine / Hybrid System › 2ZR-FXE (ENGINE MECHANICAL) › REAR CRANKSHAFT OIL SEAL › from 2020.08
RM32K0E _51 Engine / Hybrid System _059913 2ZR-FXE ENGINE MECHANICAL _0293921 REAR CRANKSHAFT OIL SEAL A

2ZR-FXE ENGINE MECHANICAL  REAR CRANKSHAFT OIL SEAL  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear crankshaft oil seal removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: If the vehicle height has changed due to suspension or tire replacement

Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Panoramic view monitor system (Click here)
Replacement of inverter with converter assembly Resolver learning
·

DTCs are stored

·

Slight vibration at a vehicle speed of 5 km/h (3 mph) or less

·

Shock or vibration during acceleration


for Nickel Metal Hydride Battery:
(Click here)
for Lithium-ion Battery:
(Click here)
Replacement of hybrid vehicle transaxle assembly
·

Resolver learning

·

Initialize resolver


Replacement of ECM Perform Vehicle Identification Number (VIN) or frame number registration MIL comes on (Click here)
·

Replacement of throttle body assembly

·

Replacement of engine assembly

·

Gas leak from exhaust system is repaired


Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Suspension, tires, etc.*1
(The vehicle height changes because of suspension or tire replacement.)
·

Measure ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


·

Parking support brake system

·

Simple intelligent parking assist system


(Click here)
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic view monitor system (Click here)
Initialize headlight ECU sub-assembly LH Automatic headlight beam level control system (Click here)
Front wheel alignment adjustment
1.

Clear zero point calibration data.

2.

Perform yaw rate and acceleration sensor zero point calibration.


·

DTCs are stored

·

ABS warning light illuminates

·

Brake warning light/yellow (minor malfunction) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


for Initialization:
(Click here)
for Calibration:
(Click here)

HINT:

When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link

*1: When performing learning using the GTS

Click here(Click here)

Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Simple intelligent parking assist system*1
Parking support brake system*1
Toyota parking assist-sensor system*1

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 31270 2.REMOVE TRANSMISSION INPUT DAMPER ASSEMBLY

a.

Using height adjustment attachments and plate lift attachments, place the engine assembly on a flat level surface.

NOTICE:
·

Using height adjustment attachments and plate lift attachments, keep the engine assembly horizontal.

·

To prevent the oil pan sub-assembly from deforming, do not place any attachments under the oil pan sub-assembly of the engine assembly.

·

Using an engine sling device and engine lift, secure the engine assembly before servicing.




b.
A372545N01
1.844,2.781 1.146,3.073 1.146,3.073 1.5,2.573 false 0.823,3.01 1.281,3.208 0.458,0.198 10 false SST

Using SST, hold the crankshaft pulley.

SST
09213-58014  (91551-80840)
09330-00021  


c.
A372546

Remove the 6 bolts and transmission input damper assembly from the flywheel sub-assembly.


Hide 13405 3.REMOVE FLYWHEEL SUB-ASSEMBLY

a.
A372547N01
1.833,2.771 1.26,3.052 1.26,3.052 1.5,2.573 false 1.094,3.115 1.552,3.313 0.458,0.198 10 false SST

Using SST, hold the crankshaft pulley.

SST
09213-58014  (91551-80840)
09330-00021  


b.
A372548

Remove the 8 bolts and flywheel sub-assembly from the crankshaft.


Hide 11401L 4.REMOVE REAR ENGINE OIL SEAL

a.
A372549C01
0.844,1.354 0.844,0.667 0.844,0.667 0.688,0.667 false 1.771,1.979 1.948,1.979 1.948,1.979 2.052,1.385 true 0.51,0.563 0.823,0.76 0.313,0.198 10 false *a 1.51,1.885 1.729,2.083 0.219,0.198 10 true *b
*a Cut Position
*b Protective Tape


Using a knife, cut through the lip of the rear engine oil seal.


b.

Using a screwdriver with its tip wrapped with protective tape, pry out the rear engine oil seal.

NOTICE:

Be careful not to damage the crankshaft.