Home › Engine / Hybrid System › CRUISE CONTROL › FRONT CAMERA SYSTEM › from 2020.08
RM32K0E _51 Engine / Hybrid System _061336 CRUISE CONTROL _0440928 FRONT CAMERA SYSTEM C

CRUISE CONTROL  FRONT CAMERA SYSTEM  C1A4A12  Buzzer Circuit Short to Battery  


DESCRIPTION

If the forward recognition camera detects a short +B in the buzzer circuit, it will store DTC C1A4A12.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1A4A12 Buzzer Circuit Short to Battery While the pre-collision city buzzer is sounding, the forward recognition camera detects a short to +B in the buzzer circuit for 2 seconds or more.
·

Pre-collision city buzzer

·

Forward recognition camera

·

Wire harness or connector



WIRING DIAGRAM

B456420E63
0.104,0.656 1.469,0.906 1.365,0.25 10 false from IG1-NO. 1 Relay 2.073,0.844 3.094,1.125 1.021,0.281 10 false ECU-IG1 NO. 4 3.313,1.219 4.885,1.448 1.573,0.229 10 false Pre-collision City Buzzer 3.323,1.052 3.677,1.26 0.354,0.208 10 false F54 3.583,0.677 3.938,0.885 0.354,0.208 10 false IG1 4.219,0.677 4.573,0.885 0.354,0.208 10 false BZ 3.396,0.594 3.563,0.771 0.167,0.177 10 false 2 4.5,0.594 4.667,0.771 0.167,0.177 10 false 1 5.521,0.698 5.875,0.906 0.354,0.208 10 false BZ 5.354,0.594 5.521,0.771 0.167,0.177 10 false 8 5.052,1.958 5.406,2.167 0.354,0.208 10 false R5 5.052,2.115 7.063,2.333 2.01,0.219 10 false Forward Recognition Camera

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle and a DTC may be stored.

·

When the forward recognition camera is replaced with a new one or the windshield glass is replaced or removed/installed, make sure to read Before Starting Adjustment, then perform optical axis alignment for the forward recognition camera and clear the vehicle control history for each system.

HINT:

Forward recognition camera axis alignment can be performed by using either One Time Recognition, Sequential Recognition or Driving Adjustment.





PROCEDURE

1.CHECK FOR DTCs
a.

Clear the DTCs.

Chassis > Front Recognition Camera > Clear DTCs
50002 430

b.

Perform the Active Test according to the display on the GTS.

NOTICE:

Perform the Active Test for 2 seconds or more.


HINT:

Performing the Active Test for 2 seconds or more causes DTC C1A4A12 to be stored if the DTC detection conditions are met.


Body Electrical > Pre-Collision System > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
PCS Warning Buzzer Sounds the pre-collision city buzzer Start / Stop Test possible with power switch on (IG), vehicle stopped
Body Electrical > Pre-Collision System > Active Test
Tester Display
PCS Warning Buzzer
50004 432 42000

c.

Check for DTCs.

Chassis > Front Recognition Camera > Trouble Codes
50001 430

Result:
Result Proceed to
DTC C1A4A12 is not output A
DTC C1A4A12 is output B



A

B

2.CHECK HARNESS AND CONNECTOR (PRE-COLLISION CITY BUZZER - FORWARD RECOGNITION CAMERA)
2.CHECK HARNESS AND CONNECTOR (PRE-COLLISION CITY BUZZER - FORWARD RECOGNITION CAMERA)
a.

Disconnect the F54 pre-collision city buzzer connector.


b.

Disconnect the R5 forward recognition camera connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F54-1 (BZ) or R5-8 (BZ) - Body ground Power switch off Below 1 V



d.

Connect the R5 forward recognition camera connector.


e.

Connect the F54 pre-collision city buzzer connector.


Result:
Proceed to
OK
NG



OK

3.INSPECT PRE-COLLISION CITY BUZZER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (PRE-COLLISION CITY BUZZER - FORWARD RECOGNITION CAMERA)