Home › Engine / Hybrid System › CRUISE CONTROL › FRONT CAMERA SYSTEM › from 2020.08
RM32K0E _51 Engine / Hybrid System _061336 CRUISE CONTROL _0440928 FRONT CAMERA SYSTEM C

CRUISE CONTROL  FRONT CAMERA SYSTEM  C1A4A14  Buzzer Circuit Short to Ground or Open  


DESCRIPTION

If the forward recognition camera detects an open or short to ground in the buzzer circuit, it will store DTC C1A4A14.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1A4A14 Buzzer Circuit Short to Ground or Open The forward recognition camera detects an open or short to ground in the buzzer circuit for 2 seconds or more.
·

Pre-collision city buzzer

·

Forward recognition camera

·

Wire harness or connector



WIRING DIAGRAM

B456420E64
0.229,0.698 1.427,1.083 1.198,0.385 10 false from IG1 IG1-NO. 1 Relay 2.073,0.844 3.094,1.125 1.021,0.281 10 false ECU-IG1 NO. 4 3.292,1.219 5.115,1.448 1.823,0.229 10 false Pre-collision City Buzzer 3.292,1.052 3.646,1.26 0.354,0.208 10 false F54 3.583,0.708 3.938,0.917 0.354,0.208 10 false IG1 4.25,0.708 4.604,0.917 0.354,0.208 10 false BZ 3.396,0.594 3.563,0.771 0.167,0.177 10 false 2 4.5,0.594 4.667,0.771 0.167,0.177 10 false 1 5.521,0.698 5.875,0.906 0.354,0.208 10 false BZ 5.354,0.594 5.521,0.771 0.167,0.177 10 false 8 5.052,1.958 5.406,2.167 0.354,0.208 10 false R5 5.052,2.115 7.063,2.333 2.01,0.219 10 false Forward Recognition Camera

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle and a DTC may be stored.

·

When the forward recognition camera is replaced with a new one or the windshield glass is replaced or removed/installed, make sure to read Before Starting Adjustment, then perform optical axis alignment for the forward recognition camera and clear the vehicle control history for each system.

HINT:

Forward recognition camera axis alignment can be performed by using either One Time Recognition, Sequential Recognition or Driving Adjustment.





PROCEDURE

1.CHECK FOR DTCs
a.

Clear the DTCs.

Chassis > Front Recognition Camera > Clear DTCs
50002 430

b.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.



c.

Check for DTCs.

Chassis > Front Recognition Camera > Trouble Codes
50001 430

Result:
Result Proceed to
DTC C1A4A14 is not output A
DTC C1A4A14 is output B



A

B

2.CHECK HARNESS AND CONNECTOR (PRE-COLLISION CITY BUZZER BATTERY CIRCUIT)
2.CHECK HARNESS AND CONNECTOR (PRE-COLLISION CITY BUZZER BATTERY CIRCUIT)
a.
B443157C66
1.5,0.177 1.906,0.438 0.406,0.26 1.99,1.333 2.5,1.156 true 0.188,0.156 0.5,0.313 0.313,0.156 10 false *a 1.573,0.229 2.031,0.427 0.458,0.198 10 false F54 2.552,1.063 3.01,1.26 0.458,0.198 10 false IG1
*a Front view of wire harness connector
(to Pre-collision City Buzzer)


Disconnect the pre-collision city buzzer connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F54-2 (IG1) - Body ground Power switch on (IG) 8 to 16 V
Power switch off Below 1 V



c.

Connect the pre-collision city buzzer connector.


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (PRE-COLLISION CITY BUZZER - FORWARD RECOGNITION CAMERA)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (PRE-COLLISION CITY BUZZER BATTERY CIRCUIT)

3.CHECK HARNESS AND CONNECTOR (PRE-COLLISION CITY BUZZER - FORWARD RECOGNITION CAMERA)
a.

Disconnect the F54 pre-collision city buzzer connector.


b.

Disconnect the R5 forward recognition camera connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F54-1 (BZ) - R5-8 (BZ) Always Below 1 Ω
F54-1 (BZ) or R5-8 (BZ) - Body ground Always 10 kΩ higher



d.

Connect the R5 forward recognition camera connector.


e.

Connect the F54 pre-collision city buzzer connector.


Result:
Proceed to
OK
NG



OK

4.INSPECT PRE-COLLISION CITY BUZZER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (PRE-COLLISION CITY BUZZER - FORWARD RECOGNITION CAMERA)