Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR AXLE CARRIER › from 2020.08
RM32K0E _52 Drivetrain _061337 AXLE AND DIFFERENTIAL _0299681 REAR AXLE CARRIER A

AXLE AND DIFFERENTIAL  REAR AXLE CARRIER  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear axle carrier sub-assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link

*1: The vehicle height changes because of suspension or tire replacement.

Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Panoramic view monitor system (Click here)
Front wheel alignment adjustment
1.

Clear zero point calibration data.

2.

Perform yaw rate and acceleration sensor zero point calibration.


·

DTCs are stored

·

ABS warning light illuminates

·

Brake warning light / yellow (minor malfunction) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


for Initialization:(Click here)
for Calibration:(Click here)
Suspension, tires, etc.*1
·

Measurement of ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


·

Parking support brake system

·

Simple intelligent parking assist system


(Click here)
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic view monitor system (Click here)

NOTICE:
·

When removing or installing the front disc brake caliper assembly, pushing back the disc brake piston may cause a large clearance between the brake pads and brake disc. When the brake pedal is depressed with a large clearance between the brake pads and the brake disc, DTC C1214 related to abnormal brake fluid pressure may be stored. Make sure to clear any DTCs after performing this step.

·

While the auxiliary battery is connected, even if the power switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.



HINT:
·

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link

*1: When performing learning using the GTS

Click here(Click here)

Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Simple intelligent parking assist system*1
Parking support brake system*1
Toyota parking assist-sensor system*1

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -


·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISABLE BRAKE CONTROL

Hide 3.REMOVE REAR WHEEL

Hide 4.SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY

Hide 42431 5.REMOVE REAR DISC

Hide 6.DISCONNECT SKID CONTROL SENSOR WIRE

Hide 42450B 7.REMOVE REAR AXLE HUB AND BEARING ASSEMBLY

Hide 8.REMOVE FLEXIBLE HOSE BRACKET

a.
C345068

Remove the bolt and flexible hose bracket from the rear axle carrier sub-assembly.


Hide 89408C 9.REMOVE REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH (w/ Height Control Sensor)

Hide 48840A 10.REMOVE REAR STABILIZER LINK ASSEMBLY

Hide 48231B 11.REMOVE REAR COIL SPRING

Hide 48258C 12.REMOVE REAR LOWER COIL SPRING INSULATOR

Hide 48720A 13.REMOVE REAR NO. 1 SUSPENSION ARM ASSEMBLY

Hide 14.REMOVE REAR AXLE CARRIER SUB-ASSEMBLY

a.
C348732

Loosen the 2 bolts of the rear trailing arm assembly.


b.
C348733C02
0.969,0.615 1.135,0.615 1.135,0.615 1.313,0.833 true 0.708,0.542 0.958,0.74 0.25,0.198 10 true *1
*1 Rear Axle Carrier Pin


Loosen the nut of the rear shock absorber assembly.

NOTICE:

Hold the rear axle carrier pin while rotating the nut.



c.
C345052C02
1.396,2.427 1.958,2.427 false 1.49,3.146 1.99,3.146 false 1.208,2.344 1.521,2.5 0.313,0.156 10 false *a 1.302,3.063 1.615,3.219 0.313,0.156 10 false *b
*a Wooden Block
*b Jack


Using a jack and a wooden block, support the rear axle carrier sub-assembly.

NOTICE:
·

When jacking up the rear axle carrier sub-assembly, be sure to jack it up slowly.

·

Make sure to perform this operation with the vehicle kept as low as possible.




d.
C345053N01
1.042,0.448 1.198,0.646 0.156,0.198 10 true A

Loosen the bolt (A).

NOTICE:

Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured.



e.

Remove the 2 bolts and separate the rear trailing arm assembly from the rear axle carrier sub-assembly.


f.

Remove the nut and separate the rear shock absorber assembly from the rear axle carrier sub-assembly.

NOTICE:

Hold the rear axle carrier pin while rotating the nut.



g.

Remove the bolt (A), nut and rear axle carrier sub-assembly from the rear upper control arm assembly.

NOTICE:

Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured.