Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › NAME PLATE › from 2020.12
RM32K0E _59 Vehicle Exterior _061792 EXTERIOR PANELS / TRIM _0304177 NAME PLATE A

EXTERIOR PANELS / TRIM  NAME PLATE  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

When installing the name plates, heat the vehicle body, back door outside garnish, front bumper assembly and name plates using a heat light.


Heating Temperature
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)
·

Back Door Outside Garnish

·

Front Bumper Assembly

·

Name Plate


20 to 30°C (68 to 86°F)

CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts, touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the vehicle body, back door outside garnish, front bumper assembly or name plate excessively.


PROCEDURE

Hide 75365 1.INSTALL FRONT FENDER EMBLEM (for TMC Made GR SPORT)

a.

Clean the vehicle body surface.

i.

Using a heat light, heat the vehicle body surface.


ii.

Remove any remaining double-sided tape from the vehicle body.


iii.

Wipe off any tape adhesive residue with cleaner.



b.

Using a heat light, heat the vehicle body and a new front fender emblem.


c.

Remove the release paper from the front fender emblem.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



d.

for LH Side:

i.

Install the front fender emblem as shown in the illustration.

B558042C02
2.042,1.25 1.865,0.844 true 1.281,0.646 1.615,1.052 true 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 0.625,1.083 0.781,1.229 0.156,0.146 10 true B 2.188,0.438 2.333,0.594 0.146,0.156 10 true A 1.99,1.802 2.167,1.958 0.177,0.156 10 true C 1.74,0.667 1.969,0.844 0.229,0.177 10 true *b 1.073,0.521 1.302,0.698 0.229,0.177 10 true *c
*a Reference Values *b Specified Installation Position
*c End of R - -


Standard Measurement:
Area Measurement Area Measurement
A 39.5 mm (1.56 in.) B 25.6 mm (1.01 in.)
C 84.0 mm (3.31 in.) - -




e.

for RH Side:

i.

Install the front fender emblem as shown in the illustration.

B558043C02
5.333,1.24 5.563,0.792 true 5.729,1.063 6.146,0.646 true 4.042,0.063 4.292,0.281 0.25,0.219 10 false *a 4.958,0.427 5.125,0.604 0.167,0.177 10 true A 6.583,1.083 6.781,1.24 0.198,0.156 10 true B 5.167,1.792 5.302,1.948 0.135,0.156 10 true C 5.479,0.625 5.698,0.792 0.219,0.167 10 true *b 6.063,0.448 6.302,0.635 0.24,0.188 10 true *c
*a Reference Values *b Specified Installation Position
*c End of R - -


Standard Measurement:
Area Measurement Area Measurement
A 49.6 mm (1.95 in.) B 24.4 mm (0.96 in.)
C 94.0 mm (3.70 in.) - -




Hide 75441C 2.INSTALL BACK DOOR NAME PLATE (for GR SPORT)

a.

Clean the vehicle body surface.

i.

Using a heat light, heat the vehicle body surface.


ii.

Remove any remaining double-sided tape from the vehicle body.


iii.

Wipe off any tape adhesive residue with cleaner.



b.

Using a heat light, heat the vehicle body and a new back door name plate.


c.

Remove the release paper from the back door name plate.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



d.

for TMC Made:

i.

Install the back door name plate as shown in the illustration.

B558044C02
4.573,1.896 5,2.167 true 6.188,2.115 6.458,2.052 true 5.927,1.865 5.573,2.167 true 3.833,0.188 4.146,0.385 0.313,0.198 10 true *a 4.125,2.219 4.271,2.365 0.146,0.146 10 true A 5.5,2.823 5.635,2.969 0.135,0.146 10 true B 5.802,2.51 5.938,2.667 0.135,0.156 10 true C 4.385,1.802 4.573,1.948 0.188,0.146 10 true *b 6.448,1.958 6.635,2.125 0.188,0.167 10 true *c 5.875,1.802 6.052,1.969 0.177,0.167 10 true *b 6,2.229 6.125,2.375 0.125,0.146 10 true D
*a Reference Values *b Specified Installation Position
*c End of R - -


Standard Measurement:
Area Measurement Area Measurement
A 18.7 mm (0.74 in.) B 97.8 mm (3.85 in.)
C 50.2 mm (1.98 in.) D 18.1 mm (0.71 in.)




e.

for TMMT Made:

i.

Install the back door name plate as shown in the illustration.

B590446C01
5.594,2.177 5.844,2 true 5.427,1.469 5.688,1.729 true 4.875,2.427 4.542,2.135 true 3.833,0.385 4.146,0.583 0.313,0.198 10 true *a 5.354,2.26 5.49,2.448 0.135,0.188 10 true A 5.938,1.333 6.073,1.479 0.135,0.146 10 true B 5.844,2.625 5.979,2.781 0.135,0.156 10 true C 5.885,1.906 6.073,2.052 0.188,0.146 10 true *b 5.24,1.365 5.417,1.531 0.177,0.167 10 true *b 4.354,2.021 4.552,2.219 0.198,0.198 10 true *c
*a Reference Values *b Specified Installation Position
*c End of R - -


Standard Measurement:
Area Measurement Area Measurement
A 19.8 mm (0.78 in.) B 59.9 mm (2.36 in.)
C 58.7 mm (2.31 in.) - -




Hide 75310A 3.INSTALL RADIATOR GRILLE EMBLEM ASSEMBLY (for TMC Made GR SPORT)

a.

Clean the front bumper assembly surface.

i.

Using a heat light, heat the front bumper assembly surface.


ii.

Remove any remaining double-sided tape from the front bumper assembly.


iii.

Wipe off any tape adhesive residue with cleaner.



b.

Using a heat light, heat the front bumper assembly and a new radiator grille emblem assembly.


c.

Remove the release paper from the radiator grille emblem assembly.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



d.
B558041C02
0.719,4.281 0.948,3.896 true 2.792,3.344 2.24,3.177 true 0.563,4.302 0.875,4.5 0.313,0.198 10 false *a 2.823,3.292 3.135,3.49 0.313,0.198 10 false *a
*a Location Pin


Engage the location pins to install the radiator grille emblem assembly as shown in the illustration.


Hide 75443 4.INSTALL NO. 3 BACK DOOR NAME PLATE

a.

Clean the back door outside garnish surface.

i.

Using a heat light, heat the back door outside garnish surface.


ii.

Remove any remaining double-sided tape from the back door outside garnish.


iii.

Wipe off any tape adhesive residue with cleaner.



b.

Using a heat light, heat the back door outside garnish and a new No. 3 back door name plate.


c.

Remove the release paper from the No. 3 back door name plate.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



d.

Install the No. 3 back door name plate as shown in the illustration.

B458890C01
4.031,0.052 4.25,0.25 0.219,0.198 10 true *a 4.344,0.906 4.531,1.104 0.188,0.198 10 true A 5.188,1 5.375,1.198 0.188,0.198 10 true B 5.698,0.958 5.885,1.156 0.188,0.198 10 true C 5.26,1.688 5.448,1.885 0.188,0.198 10 true D
*a Reference Values - -


Standard Measurement:
Area Measurement Area Measurement
A 115.8 mm (4.56 in.) B 78.9 mm (3.106 in.)
C 74.3 mm (2.93 in.) D 191.4 mm (7.54 in.)



Hide 75374 5.INSTALL SIDE PANEL EMBLEM

a.

Clean the vehicle body surface.

i.

Using a heat light, heat the vehicle body surface.


ii.

Remove any remaining double-sided tape from the vehicle body.


iii.

Wipe off any tape adhesive residue with cleaner.



b.

Using a heat light, heat the vehicle body and a new side panel emblem.


c.

Remove the release paper from the side panel emblem.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



d.

for LH Side:

i.

Install the side panel emblem as shown in the illustration.

B458891C01
0.156,0.063 0.469,0.26 0.313,0.198 10 false *a 0.542,1.021 0.708,1.219 0.167,0.198 10 true A 2.865,1.073 3.031,1.271 0.167,0.198 10 true B 2.323,1.698 2.49,1.896 0.167,0.198 10 true C 1.635,0.604 1.802,0.802 0.167,0.198 10 true D
*a Reference Values - -


Standard Measurement:
Area Measurement Area Measurement
A 85.5 mm (3.37 in.) B 42.8 mm (1.69 in.)
C 62.6 mm (2.46 in.) D 195.5 mm (7.70 in.)




e.

for RH Side:

i.

Install the side panel emblem as shown in the illustration.

B458892C01
4.479,0.073 4.792,0.271 0.313,0.198 10 false *a 4.188,1.052 4.5,1.25 0.313,0.198 10 false B 6.469,0.948 6.646,1.135 0.177,0.188 10 true A 4.76,1.708 4.938,1.896 0.177,0.188 10 true C 5.583,0.594 5.76,0.781 0.177,0.188 10 true D
*a Reference Values - -


Standard Measurement:
Area Measurement Area Measurement
A 90.6 mm (3.57 in.) B 45.9 mm (1.807 in.)
C 55.8 mm (2.20 in.) D 190.4 mm (7.50 in.)




Hide 75431A 6.INSTALL NO. 1 BACK DOOR EMBLEM

a.

Clean the back door outside garnish surface.

i.

Using a heat light, heat the back door outside garnish surface.


ii.

Remove any remaining double-sided tape from the back door outside garnish.


iii.

Wipe off any tape adhesive residue with cleaner.



b.

Using a heat light, heat the back door outside garnish and a new No. 1 back door emblem.


c.

Remove the release paper from the No. 1 back door emblem.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



d.
B458672C01
0.448,3.854 0.677,3.469 true 2.896,3.885 2.677,3.469 true 0.344,3.875 0.656,4.073 0.313,0.198 10 false *a 2.865,3.938 3.177,4.135 0.313,0.198 10 false *a
*a Location Pin


Engage the location pins and install the No. 1 back door emblem as shown in the illustration.


Hide 75441E 7.INSTALL NO. 1 BACK DOOR NAME PLATE

a.

Clean the back door outside garnish surface.

i.

Using a heat light, heat the back door outside garnish surface.


ii.

Remove any remaining double-sided tape from the back door outside garnish.


iii.

Wipe off any tape adhesive residue with cleaner.



b.

Using a heat light, heat the back door outside garnish and a new No. 1 back door name plate.


c.

Remove the release paper from the No. 1 back door name plate.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



d.

Install the No. 1 back door name plate as shown in the illustration.

B458673C01
4.094,0.073 4.406,0.271 0.313,0.198 10 false *a 3.979,1.021 4.167,1.219 0.188,0.198 10 true A 6.198,0.938 6.385,1.135 0.188,0.198 10 true B 4.625,1.74 4.813,1.938 0.188,0.198 10 true C
*a Reference Values - -


Standard Measurement:
Area Measurement Area Measurement
A 57.0 mm (2.24 in.) B 85.5 mm (3.37 in.)
C 83.2 mm (3.28 in.) - -



Hide 75442A 8.INSTALL NO. 2 BACK DOOR NAME PLATE

a.

Clean the back door outside garnish surface.

i.

Using a heat light, heat the back door outside garnish surface.


ii.

Remove any remaining double-sided tape from the back door outside garnish.


iii.

Wipe off any tape adhesive residue with cleaner.



b.

Using a heat light, heat the back door outside garnish and a new No. 2 back door name plate.


c.

Remove the release paper from the No. 2 back door name plate.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



d.

Install the No. 2 back door name plate as shown in the illustration.

B458675C01
4.094,0.083 4.406,0.281 0.313,0.198 10 false *a 4.646,0.865 4.865,1.063 0.219,0.198 10 true A 6.031,0.865 6.25,1.063 0.219,0.198 10 true B
*a Reference Values - -


Standard Measurement:
Area Measurement Area Measurement
A 65.1 mm (2.56 in.) B 113.7 mm (4.48 in.)