Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for Radio and Display Type with Single Knob Type) › from 2022.01
RM32K0E _56 Audio / Visual / Telematics _061290 NAVIGATION / MULTI INFO DISPLAY _0522654 NAVIGATION SYSTEM(for Radio and Display Type with Single Knob Type) C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Radio and Display Type with Single Knob Type)  B15A387  Stereo Component Amplifier Missing Message  


DESCRIPTION

This DTC is stored when the radio and display receiver assembly detects that the stereo component amplifier assembly has disconnected.

DTC No. Detection Item DTC Detection Condition Trouble Area
B15A387 Stereo Component Amplifier Missing Message When 3 minutes has elapsed after turning the ignition switch to ON and the stereo component amplifier assembly cannot be detected, the stereo component amplifier assembly is judged to be disconnected after comparison with the past registered devices history.
(2 trip detection logic)
·

Radio and display receiver assembly

·

Stereo component amplifier assembly

·

Harness or connector



WIRING DIAGRAM

E469815E03
5.292,0.771 5.604,0.99 0.313,0.219 10 false F75 5.646,0.729 5.875,0.938 0.229,0.208 10 false +B 0.354,0.729 1.854,0.948 1.5,0.219 10 false from Auxiliary Battery 2.615,2.646 3.094,2.854 0.479,0.208 10 false F174 2.604,2.823 4.323,3.198 1.719,0.375 10 false Radio and Display Receiver Assembly 1.26,4.271 3.271,4.479 2.01,0.208 10 false : AVC-LAN Communication Line 5.146,3.708 6.896,4.063 1.75,0.354 10 false Stereo Component Amplifier Assembly 5.313,3.073 5.51,3.229 0.198,0.156 10 false 18 5.344,2.688 5.5,2.875 0.156,0.188 10 false 3 5.365,2.073 5.521,2.25 0.156,0.177 10 false 7 5.354,1.573 5.531,1.76 0.177,0.188 10 false 8 5.292,0.969 5.521,1.177 0.229,0.208 10 false 16 5.344,0.563 5.479,0.771 0.135,0.208 10 false 1 5.656,1.75 5.948,1.958 0.292,0.208 10 false TX+ 5.667,2.844 6.021,3.042 0.354,0.198 10 false GND 3.677,2.125 3.823,2.302 0.146,0.177 10 false 2 3.667,1.625 3.844,1.833 0.177,0.208 10 false 1 5.635,1.125 5.958,1.333 0.323,0.208 10 false +B2 5.635,2.208 5.875,2.385 0.24,0.177 10 false TX- 5.625,3.25 6.104,3.458 0.479,0.208 10 false GND2 3.24,1.771 3.615,1.958 0.375,0.188 10 false TX1+ 3.271,2.24 3.583,2.448 0.313,0.208 10 false TX1- 5.292,1.167 5.583,1.365 0.292,0.198 10 false F75 5.292,2.896 5.635,3.094 0.344,0.198 10 false F75 5.302,3.271 5.583,3.458 0.281,0.188 10 false F75 5.271,1.781 5.802,1.99 0.531,0.208 10 false F152 5.26,2.271 5.823,2.5 0.563,0.229 10 false F152 3.781,1.302 4.615,1.521 0.833,0.219 10 false AMP NO. 2 0.479,3.448 2.927,3.646 2.448,0.198 10 false *1: for M20A-FXS 0.469,3.813 2.76,4.01 2.292,0.198 10 false *2: for 2ZR-FXE 3.417,0.896 6.021,1.094 2.604,0.198 10 false AMP*1 AMP NO. 1*2

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type with Single Knob Type)>PRECAUTION



HINT:

There may be a communication malfunction due to noise affecting communication between devices on the AVC-LAN.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - POWER SOURCE AND BODY GROUND)
a.

Disconnect the F75 stereo component amplifier assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F75-3 (GND) - Body ground Always Below 1 Ω
F75-18 (GND2) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F75-1 (+B) - Body ground Always 11 to 14 V
F75-16 (+B2) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)
a.

Disconnect the F174 radio and display receiver assembly connector.


b.

Disconnect the stereo component amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F174-1 (TX1+) - F152-8 (TX+) Always Below 1 Ω
F174-2 (TX1-) - F152-7 (TX-) Always Below 1 Ω
F174-1 (TX1+) or F152-8 (TX+) - Body ground Always 10 kΩ or higher
F174-2 (TX1-) or F152-7 (TX-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY
a.

Replace the stereo component amplifier assembly with a new or known good one.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>STEREO COMPONENT AMPLIFIER>REMOVAL


Result:
Proceed to
NEXT



NEXT

4.CHECK FOR DTC
4.CHECK FOR DTC
a.

Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs
50002 496

b.

Turn the ignition switch off.


c.

Turn the ignition switch to ON and wait for 60 seconds.


d.

Turn the ignition switch off.


e.

Turn the ignition switch to ON and wait for 60 seconds.


f.

Check for DTCs and proceed to the following step.

Body Electrical > Navigation System > Trouble Codes
50001 496

Result:
Result Proceed to
DTCs are not output A
DTC B15A387 is output B



A

END (STEREO COMPONENT AMPLIFIER ASSEMBLY IS DEFECTIVE)

B