Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for Radio and Display Type with Single Knob Type) › from 2022.01
RM32K0E _56 Audio / Visual / Telematics _061290 NAVIGATION / MULTI INFO DISPLAY _0522654 NAVIGATION SYSTEM(for Radio and Display Type with Single Knob Type) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Radio and Display Type with Single Knob Type)  AVC-LAN Circuit  


DESCRIPTION

The audio and visual system communicates with each device via AVC-LAN communication. If a malfunction such as a short in a communication line, short to +B or short to ground occurs in the AVC-LAN circuit, communication will stop and the audio and visual system will not operate correctly. The malfunctioning device can be identified if the system returns to normal when the malfunctioning device is disconnected from the AVC-LAN circuit.

WIRING DIAGRAM

E425796E05
2.958,2.208 4.938,2.396 1.979,0.188 10 false : AVC-LAN Communication Line 1.01,1.469 1.469,1.667 0.458,0.198 10 false F152 5.094,0.583 5.552,0.781 0.458,0.198 10 false TX1+ 5.052,1.615 6.26,2.063 1.208,0.448 10 false Radio and Display Receiver Assembly 0.99,1.625 2.198,2.198 1.208,0.573 10 false Stereo Component Amplifier Assembly 5.052,1.469 5.51,1.667 0.458,0.198 10 false F174 5.104,0.979 5.563,1.177 0.458,0.198 10 false TX1- 4.906,0.438 5.104,0.615 0.198,0.177 10 false 1 4.896,0.833 5.094,1.01 0.198,0.177 10 false 2 1.844,0.573 2.302,0.771 0.458,0.198 10 false TX+ 1.875,0.948 2.115,1.156 0.24,0.208 10 false TX- 2.177,0.448 2.375,0.625 0.198,0.177 10 false 8 2.177,0.833 2.375,1.01 0.198,0.177 10 false 7

CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM (for Radio and Display Type with Single Knob Type)>PRECAUTION


PROCEDURE

1.REMOVE DEALER INSTALLED OPTIONAL DEVICES (AVC-LAN COMPATIBLE DEVICES)
a.

Disconnect the connector of each dealer installed optional device (AVC-LAN compatible device) and check if the malfunction continues.


Result:
Result Proceed to
No dealer installed optional devices are installed A
The malfunction reoccurs
The system returns to normal B



A

2.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY (TX1+, TX1-)

B

REPLACE THE DEVICE (OR WIRE HARNESS)

2.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY (TX1+, TX1-)
a.

b.
E466873C07
2.74,0.427 2.896,0.427 false 2.552,0.969 2.74,0.427 true 2.344,0.979 2.167,0.458 true 2.01,0.458 2.167,0.458 false 0.125,0.094 0.438,0.292 0.313,0.198 10 false *a 2.958,0.354 3.344,0.521 0.385,0.167 10 false TX1+ 1.646,0.385 2.26,0.583 0.615,0.198 10 false TX1-
*a Component without harness connected
(Radio and Display Receiver Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1(TX1+) - 2(TX1-) Always 60 to 80 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (AVC-LAN CIRCUIT)

NG

3.CHECK HARNESS AND CONNECTOR (AVC-LAN CIRCUIT)
a.

Disconnect the F174 radio and display receiver assembly connector.


b.

Disconnect the F152 stereo component amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F174-1(TX1+) - F152-8(TX+) Always Below 1 Ω
F174-2(TX1-) - F152-7(TX-) Always Below 1 Ω
F174-1(TX1+) or F152-8(TX+) - Body ground Always 10 kΩ or higher
F174-2(TX1-) or F152-7(TX-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK AVC-LAN COMPATIBLE DEVICES (DISCONNECT CONNECTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK AVC-LAN COMPATIBLE DEVICES (DISCONNECT CONNECTOR)
a.

Disconnect the connector of each AVC-LAN connected device and check if the malfunction continues.


Result:
Result Proceed to
The malfunction continues A
The system returns to normal (AVC-LAN connected device was malfunctioning) B



A

5.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY (AVC-LAN VOLTAGE)

B

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY

5.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY (AVC-LAN VOLTAGE)
a.
E466872C04
2.563,0.917 2.76,0.365 true 2.76,0.365 2.896,0.365 false 2.385,0.896 2.323,0.354 true 2.323,0.344 2.188,0.344 false 0.188,0.156 0.5,0.354 0.313,0.198 10 false *a 2.969,0.313 3.406,0.5 0.438,0.188 10 false TX1+ 1.833,0.281 2.448,0.479 0.615,0.198 10 false TX1-
*a Component with harness connected
(Radio and Display Receiver Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D174-1(TX1+) - F174-2(TX1-) ACC ON Approximately 0 V
F174-1(TX1+) - Body ground ACC ON Approximately 2.5 V
F174-2(TX1-) - Body ground ACC ON Approximately 2.5 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR MALFUNCTIONING AVC-LAN CONNECTED DEVICE