This DTC is stored when a malfunction occurs in the back window glass (digital audio broadcasting antenna (main)) which is connected to the radio and display receiver assembly.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B157D13 | DAB (Digital Audio Broadcasting) Antenna Circuit Open | The digital audio broadcasting antenna (main) is not connected
(2 trip detection logic) |
·
Antenna cord sub-assembly ·
No. 2 Antenna cord sub-assembly ·
No. 3 Antenna cord sub-assembly ·
No. 4 Antenna cord sub-assembly ·
No. 2 amplifier antenna assembly ·
Digital audio broadcasting antenna assembly ·
Back window glass (window glass antenna wire) ·
Radio and display receiver assembly |
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed.
Check if the digital audio broadcasting antenna cable is securely connected to the radio and display receiver assembly.
Digital audio broadcasting antenna cable is securely connected
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for continuity in the window glass antenna wire.
Digital audio broadcasting antenna cable is securely connected
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(to Radio and Display Receiver Assembly) |
Disconnect the antenna connector from the radio and display receiver assembly.
| *a | Component without harness connected
(to No. 2 Antenna Cord Sub-assembly) |
Disconnect the antenna connector from the No. 2 antenna cord sub-assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| GNSS-1 (DAB) - A-1 | Always | Below 1 Ω |
| GNSS-1a - A-1a | Always | Below 1 Ω |
| GNSS-1 (DAB) or A-1 - Body ground | Always | 10 kΩ or higher |
| GNSS-1a or A-1a - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(to Antenna Cord Sub-assembly) |
Disconnect the antenna connector from the antenna cord sub-assembly.
| *a | Component without harness connected
(to No. 3 Antenna Cord Sub-assembly) |
Disconnect the antenna connector from the No. 3 antenna cord sub-assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B-1 - C-1 | Always | Below 1 Ω |
| B-1a - C-1a | Always | Below 1 Ω |
| B-1 or C-1 - Body ground | Always | 10 kΩ or higher |
| B-1a - C-1a - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(to No. 2 Antenna Cord Sub-assembly) |
Disconnect the antenna connector from the No. 2 antenna cord sub-assembly.
| *a | Component without harness connected
(to No. 4 Antenna Cord Sub-assembly) |
Disconnect the antenna connector from the No. 4 antenna cord sub-assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D-1 - E-1 | Always | Below 1 Ω |
| D-1a - E-1a | Always | Below 1 Ω |
| D-1 or E-1 - Body ground | Always | 10 kΩ or higher |
| D-1a or E-1a - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(to No. 3 Antenna Cord Sub-assembly) |
Disconnect the antenna connector from the No. 3 antenna cord sub-assembly.
| *a | Component without harness connected
(to No. 2 Amplifier Antenna Assembly) |
Disconnect the antenna connector from the No. 2 amplifier antenna assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F-1 - G-1 | Always | Below 1 Ω |
| F-1a - G-1a | Always | Below 1 Ω |
| F-1 or G-1 - Body ground | Always | 10 kΩ or higher |
| F-1a or G-1a - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the No. 2 amplifier antenna assembly with a new or known good one.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>DIGITAL AUDIO BROADCASTING ANTENNA>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Turn the ignition switch off.
Recheck for DTCs and check that no DTCs are output.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output | B |
A
B
Replace the digital audio broadcasting antenna assembly with a new or known good one.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>DIGITAL AUDIO BROADCASTING ANTENNA>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Turn the ignition switch off.
Recheck for DTCs and check that no DTCs are output.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output | B |
A
B
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio and Display Type)>REMOVAL