FAIL-SAFE FUNCTION
When communication fails in any of the CAN bus lines (communication lines), a fail-safe function(s) will operate. The fail-safe function that is specified for each system operates to prevent those systems from malfunctioning.
The following table shows the effects on each system when communication is impossible. (For further details, see the pages for each system.)
| Function | Control Master
(Main ECU to determine controls) |
System Related | Fail-safe Operation | Driver Detectable | DTC Detection
(ECU that stored DTC) |
|---|---|---|---|---|---|
| Air Conditioning Control
·
Assists with passing signals between the air conditioning amplifier assembly and air conditioning inverter. |
Hybrid vehicle control ECU | Air conditioning amplifier assembly | Air conditioning control is limited. | MIL illuminates. | U016487
(Hybrid vehicle control ECU) |
| Regenerative Operation
·
Provides maximum amount of regeneration based on cooperative control with the ECB system. |
Hybrid vehicle control ECU | Brake booster with master cylinder assembly | Normal driving | MIL illuminates. | U117087
(Hybrid vehicle control ECU) |
| Drive Torque Control
·
Controls the engine, generator (MG1) and motor (MG2) based on engine information received. |
Hybrid vehicle control ECU | ECM | ·
Reduced output power ·
Driving range is limited ·
Engine always stopped |
MIL illuminates. | U010087
(Hybrid vehicle control ECU) |
| Drive Torque Control
·
Controls the generator (MG1) and motor (MG2). |
Hybrid vehicle control ECU | Inverter with converter assembly | Normal driving | - | U011087
(Hybrid vehicle control ECU) |
| Drive Torque Control
·
Controls the ECB. ·
Cruise Control. |
Hybrid vehicle control ECU | Brake booster with master cylinder assembly | Normal driving | - | U012987
(Hybrid vehicle control ECU) |
| Vehicle Damage Determination
·
Determines whether there was a collision according to the airbag signal. |
Hybrid vehicle control ECU | Airbag sensor assembly | Normal driving | - | U015187
(Hybrid vehicle control ECU) |
| Motor/Generator Control
·
Controls the motor and generator by calculating the optimum voltage and current based on the requested torque value and the rotation angles of the motor and generator. |
·
Inverter with converter assembly ·
Hybrid vehicle control ECU |
·
ECM ·
Hybrid vehicle control ECU ·
Brake booster with master cylinder assembly |
·
When the brake booster with master cylinder assembly is not communicating: Normal driving possible (regeneration is not performed) ·
When an ECU other than the brake booster with master cylinder assembly is not communicating: Normal driving possible |
·
Master warning light turns on. ·
MIL illuminates. |
U010087
U029387 U117087 (Inverter with converter assembly) |
| Battery Control
·
Calculates the battery charge and discharge capacity. |
Battery ECU assembly | ·
Hybrid vehicle control ECU ·
ECM |
Control is performed the same as when the HV battery is not installed to the vehicle. | ·
Master warning light turns on. ·
MIL illuminates. |
U010087
U029387 U115087 (Battery ECU assembly) |
| Static Braking
·
When the vehicle is stopped, the parking brake electronically operates to hold the vehicle in place when the driver operates the switch. |
Brake actuator assembly | Brake booster with master cylinder assembly | It cannot be determined whether the vehicle is stopped or not (there is no effect on this function). | The electric parking brake warning light illuminates. | U0073
U0129 (Brake actuator assembly) |
| Dynamic Parking Brake
·
Slows down the moving vehicle with the parking brake. Braking power is only effective while pressing the switch. Once the switch is released, the parking brake is automatically released. |
Brake actuator assembly | Brake booster with master cylinder assembly | It cannot be determined whether the vehicle is stopped or not (there is no effect on this function). | The electric parking brake warning light illuminates. | U0073
U0129 (Brake actuator assembly) |
| Shift-linked Function
·
When the shift lever is moved to P, the electric parking brake automatically operates. If the shift lever is moved to D, N or R, the electric parking brake is automatically released. |
Brake actuator assembly | ·
Brake booster with master cylinder assembly ·
Airbag sensor assembly ·
ECM ·
Hybrid vehicle control ECU |
The shift-linked function is prohibited. | ·
The electric parking brake warning light illuminates. ·
When the vehicle starts off, the vehicle may feel a slight drag due to the parking brake being released late. |
U0073
U0100 U0124 U0129 U0293 (Brake actuator assembly) |
| Brake Hold Function
·
Prevents the vehicle from moving when the brake pedal is released while the vehicle is stopped. Automatically operates the electric parking brake according to requests from the skid control ECU. |
Brake actuator assembly | Brake booster with master cylinder assembly | Brake hold control is prohibited. | When transmission is lost: -
Brake hold control is prohibited before brake fluid pressure is applied. -
While brake fluid pressure is applied, if the brake pedal is depressed after "Depress the brake pedal" is displayed on the multi-information display, brake hold control is prohibited. When communication is lost: -
The electric parking brake warning light illuminates. -
When the fail-safe function is operating (during a brake problem), the parking brake operation becomes delayed. The electric parking brake warning light illuminates. |
U0073
U0129 (Brake actuator assembly) |
| ABS control | Brake booster with master cylinder assembly | Airbag sensor assembly | When control is being performed:
·
When back-up control (vehicle behavior stabilization) is complete, braking returns to normal and further control is prohibited. When control is not being performed: ·
Control will not be started. |
·
ABS warning light illuminates. ·
SLIP indicator illuminates. ·
Brake warning light (red) illuminates. ·
Brake hold operated indicator light blinks. ·
Brake warning light (yellow) illuminates. |
U0073
U0123 U0124 (Brake booster with master cylinder assembly) |
| VSC/TRC/VDIM control | Brake booster with master cylinder assembly | ·
Hybrid vehicle control ECU ·
Steering sensor ·
Airbag sensor assembly ·
Power steering ECU assembly |
When control is being performed:
·
When back-up control (vehicle behavior stabilization) is complete, braking returns to normal and further control is prohibited. When control is not being performed: ·
Control will not be started. |
·
ABS warning light illuminates. ·
SLIP indicator illuminates. ·
Brake hold operated indicator light blinks. ·
Brake warning light (red) illuminates. ·
Brake warning light (yellow) illuminates. |
U0073
U0123 U0124 U0126 U0293 (Brake booster with master cylinder assembly) |
| Hill-start Assist Control
·
Maintains the brake hydraulic pressure to the 4 wheels for 2 seconds with the brake pedal released when starting off on an uphill. |
Brake booster with master cylinder assembly | ·
Hybrid vehicle control ECU assembly ·
Steering sensor ·
Airbag sensor assembly |
When control is being performed:
·
When back-up control (Depressurization control) is complete, braking returns to normal and further control is prohibited. When control is not being performed: ·
Control will not be started. |
·
Brake warning light (red) illuminates. ·
ABS warning light illuminates. ·
SLIP indicator illuminates. ·
Brake hold operated indicator light blinks. ·
Brake warning light (yellow) illuminates. |
U0073
U0123 U0124 U0126 U0293 (Brake booster with master cylinder assembly) |
| Hybrid Vehicle Regenerative Brake Coordinated Control
·
Performs regenerative brake coordinated control with the hybrid control system. |
Brake booster with master cylinder assembly | ·
Hybrid vehicle control ECU ·
Airbag sensor assembly ·
Certification ECU (smart key ECU assembly) |
During control:
·
When normal control is complete, hybrid vehicle regenerative brake coordinated control is prohibited. Not during control: ·
Control will not be started. |
·
ABS warning light illuminates. ·
SLIP indicator light illuminates. ·
Brake hold operated indicator light blinks. ·
Brake warning light (yellow) illuminates. |
U0123
U0124 (Brake booster with master cylinder assembly) |
| During control:
·
Control is continued with previous values and then the brake pedal control amount is gradually changed. Then, hybrid vehicle regenerative brake coordinated control is prohibited. Not during control: ·
Control will not be started. |
·
Brake warning light (red) illuminates. ·
ABS warning light illuminates. ·
SLIP indicator light illuminates. ·
Brake hold operated indicator light blinks. ·
Brake warning light (yellow) illuminates. |
U0073
U0120 U0293 (Brake booster with master cylinder assembly) |
|||
| Brake Hold Control
·
Maintains the brake oil pressure when the vehicle is stopped. |
Brake booster with master cylinder assembly | ·
Airbag sensor assembly ·
Brake actuator assembly ·
Hybrid vehicle control ECU |
When control is being performed:
·
When normal control is complete, brake hold control is prohibited. When control is not being performed: ·
Control will not be started. |
·
ABS warning light illuminates. ·
SLIP indicator illuminates. ·
Brake hold operated indicator light blinks. ·
Brake warning light (yellow) illuminates. |
U0123
U0124 (Brake booster with master cylinder assembly) |
| When control is being performed:
·
A message is displayed on the multi-information display and brake hold control is canceled when the brake pedal is depressed. When control is not being performed: ·
Control will not be started. |
·
Brake warning light (red) illuminates. ·
ABS warning light illuminates. ·
SLIP indicator illuminates. ·
Brake hold operated indicator light blinks. ·
Brake warning light (yellow) illuminates. |
U0073
U0128 U0293 (Brake booster with master cylinder assembly) |
|||
| Vehicle Speed Display | Combination meter assembly | Brake booster with master cylinder assembly | Speedometer is controlled based on a default vehicle speed of 0 km/h (0 mph). | - | U0129
(Combination meter assembly) |
| Hybrid System Indicator Display | Combination meter assembly | Hybrid vehicle control ECU | Needle of hybrid system indicator remains at 201. | - | U0100
(Combination meter assembly) |
| Meter Display
·
Displays vehicle condition and controls indicator lights. |
Combination meter assembly | ·
Power steering ECU assembly ·
Airbag sensor assembly ·
Brake booster with master cylinder assembly ·
ECM ·
Forward recognition camera ·
Headlight ECU sub-assembly LH |
·
Vehicle information is not displayed. ·
Lights do not illuminate or lights remain illuminated. |
- | U0100
U0129 U0131 U0151 U0182 (Combination meter assembly) |
| Air Conditioning Control
·
Corrects engine speed, such as for idle up. ·
Controls outlet air temperature, outlet mode change and airflow volume based on engine coolant temperature signal. ·
Corrects engine coolant temperature map and changes compressor lock judgment value. |
Air conditioning amplifier assembly | Hybrid vehicle control ECU | Control is performed based on default coolant temperature of 80°C (176°F). | - | U0293
(Air conditioning amplifier assembly) |
| Simple Load Control
·
Performs electric load control according to load control level signal. |
Air conditioning amplifier assembly | Power steering ECU assembly | While the power switch is on (IG), previous values are maintained (during a reset, there is no load control). | - | U0131
(Air conditioning amplifier assembly) |
| Panel Dimming Control
·
Outputs dimming information to the A/C panel according to the display dimming information. |
Air conditioning amplifier assembly | Main body ECU (multiplex network body ECU) | While the power switch is on (IG), previous values are maintained (during a reset, dimming control is performed). | - | U0142
(Air conditioning amplifier assembly) |
| Destination Determination Control
·
Switches the A/C control pattern according to the destination information. |
Air conditioning amplifier assembly | Main body ECU (multiplex network body ECU) | While the power switch is on (IG), previous values are maintained. | - | U0142
(Air conditioning amplifier assembly) |
| Ambient Temperature Correction Control
·
Switches air conditioning system operation condition and corrects value of displayed ambient temperature according to vehicle speed signal. |
Air conditioning amplifier assembly | Combination meter assembly | Control is performed based on default vehicle speed of 0 km/h (0 mph). | ·
Correction level for displayed ambient temperature declines. ·
Correction level for outlet airflow declines. |
U0155
(Air conditioning amplifier assembly) |
| Solar Calibration Control
·
Calibrates air conditioning control using the value from the solar sensor. |
Air conditioning amplifier assembly | Main body ECU (multiplex network body ECU) | While the power switch is on (IG), previous values are maintained. | - | U0142
(Air conditioning amplifier assembly) |
| Blind Spot Monitor Control
·
Detects vehicle in blind spot of adjacent lane and informs driver. |
Blind spot monitor sensor LH | ·
Steering sensor ·
Brake booster with master cylinder assembly ·
Main body ECU (multiplex network body ECU) ·
Hybrid vehicle control ECU |
- | Displays messages on the multi-information display. | U0126
U0129 U0142 U0293 (Blind spot monitor sensor LH) |
| Lane Departure Alert System
·
Alerts the driver of the possibility of lane departure and performs steering control to assist the vehicle in returning to the center of the road. |
Forward recognition camera | ·
Hybrid vehicle control ECU ·
ECM ·
Steering sensor ·
Brake booster with master cylinder assembly ·
Power steering ECU assembly ·
Combination meter assembly ·
Millimeter wave radar sensor assembly |
The system is stopped. | Displays messages on the multi-information display. | U010087
U010187 U012687 U012987 U013187 U015587 U023587 U029387 U030051 U030057 (Forward recognition camera) |
| Lane Tracing Assist System
·
Recognizes the lane with the front camera and assists the vehicle in driving the center of the road. |
Forward recognition camera | ·
Hybrid vehicle control ECU ·
ECM ·
Steering sensor ·
Brake booster with master cylinder assembly ·
Power steering ECU assembly ·
Combination meter assembly ·
Millimeter wave radar sensor assembly |
The system is stopped. | Displays messages on the multi-information display. | U010087
U010187 U012687 U012987 U013187 U015587 U023587 U029387 U030051 U030057 (Forward recognition camera) |
| Road Sign Assist
·
Recognizes the sign with the front camera and displays the recognized sign on the meter. |
Forward recognition camera | ·
Hybrid vehicle control ECU ·
Brake booster with master cylinder assembly ·
Main body ECU (multiplex network body ECU) ·
Combination meter assembly |
Stops the road sign display. | Displays messages on the multi-information display. | U012987
U014087 U015587 U029387 (Forward recognition camera) |
| Automatic High Beam System / Adaptive High Beam System
·
Uses the front camera to recognize headlights and taillights and sends that target information to the control ECU. |
Forward recognition camera | ·
Hybrid vehicle control ECU ·
ECM ·
Main body ECU (multiplex network body ECU) ·
Brake booster with master cylinder assembly |
Previous value is maintained. | ·
Displays messages on the multi-information display. ·
Automatic high beam indicator light illuminates. |
U010087
U010187 U012987 U014087 U023587 U029387 (Forward recognition camera) |
| Forward Recognition Camera System
·
Sends the common calculation and recognition result to each application in the forward recognition camera. |
Forward recognition camera | ·
Hybrid vehicle control ECU ·
ECM ·
Steering sensor ·
Brake booster with master cylinder assembly ·
Combination meter assembly ·
Main body ECU (multiplex network body ECU) |
·
Detection is disabled. ·
Previous value is maintained. |
- | U010087
U010187 U012687 U012987 U014087 U015587 U029387 U030051 U030057 U032251 U032257 (Forward recognition camera) |
| Pre-collision System
·
Controls the brakes immediately before a crash. |
Millimeter wave radar sensor assembly | ·
ECM ·
Forward recognition camera ·
Brake booster with master cylinder assembly ·
Steering sensor ·
Hybrid vehicle control ECU ·
Airbag sensor assembly |
Control stops. | Displays messages on the multi-information display. | U010087
U010187 U012587 U012687 U012987 U015587 U023A87 U029387 (Millimeter wave radar sensor assembly) |
| Entry Function
·
Entry lock/unlock and back door unlatch ·
Warning ·
Performs entry illumination (Interior illumination, etc.). ·
Displays messages to inform the driver that it is possible to start the hybrid control system. |
·
Main body ECU (multiplex network body ECU) ·
Certification ECU (smart key ECU assembly) |
·
ECM ·
Main body ECU (multiplex network body ECU) ·
Combination meter assembly |
·
Entry lock/ unlock or back door unlatch does not operate. ·
Warning functions (Key confinement, Key not in vehicle, Key reminder etc.) do not operate, Key confinement prevention control does not operate. ·
Entry illumination does not operate. |
- | U0100
U0142 U0155 (Certification ECU (smart key ECU assembly)) |
| Wireless Function
·
Operates the wireless lock/unlock functions, etc. |
Certification ECU (smart key ECU assembly) | Main body ECU (multiplex network body ECU) | Wireless lock/unlock function do not operate. | - | U0142
(Certification ECU (smart key ECU assembly)) |
| Power Switch Backlighting Control
·
Turns on/off power switch illumination linked with interior lights etc. |
Certification ECU (smart key ECU assembly) | Main body ECU (multiplex network body ECU) | ·
When the power switch backlight is not illuminated: Does not illuminate. ·
When the power switch backlight is illuminated as the DOME light illuminates: Does not turn off. |
- | U0142
(Certification ECU (smart key ECU assembly)) |
| Security Indicator Display Function
·
Displays the immobiliser security condition. |
Certification ECU (smart key ECU assembly) | ·
Main body ECU (multiplex network body ECU) ·
Hybrid vehicle control ECU |
·
Security condition cannot display normally (illuminates during security warning preparation/security warning). ·
Entry and start warning cannot display normally. -
When the hybrid control system is activated, the message to show how to activate the hybrid control system does not turn off immediately. -
When the hybrid control system is activated, the low key battery warning is not displayed. |
- | U0142
U0293 (Certification ECU (smart key ECU assembly)) |
| Air Conditioning Control (for Radio and Display Type with Dual Knob Type)
·
Controls air conditioning functions such as set temperature adjustment, air outlet selection, etc. by operating display audio controller or Remote Touch. |
Radio and display receiver assembly | Air conditioning amplifier assembly | ·
Air conditioning system indicators turn off. ·
If set temperature is shown on multi-information display or multi-display, set temperature display turns off. |
Displays messages on the multi-information display. | U0073
U0164 (Radio and display receiver assembly) |
| HV Energy Flow Display (for Radio and Display Type with Dual Knob Type)
·
Creates energy flow screen which indicates regeneration status and drive force transmission status. |
Radio and display receiver assembly | Hybrid vehicle control ECU | If communication stops while the energy flow screen is displayed, the energy flow display disappears and the latest value is maintained for the SOC (state of charge) level display. | - | U0293
(Radio and display receiver assembly) |
| Destination Identification (for Radio and Display Type with Dual Knob Type)
·
Identifies destination based on destination and destination package information, and selects the time zone and language used for the display. |
Radio and display receiver assembly | Main body ECU (multiplex network body ECU) | Determines the destination according to the last received value and operates accordingly (if there is no last received value, the system operates using the default value). | Time zone and language selection screen are different from actual destination. | U0140
(Radio and display receiver assembly) |
| Vehicle Customize Function (for Radio and Display Type with Dual Knob Type)
·
Changes the behavior and control parameters of various functions (illumination lighting time, etc.) according to the user operation via the screen. |
Radio and display receiver assembly | ·
Main body ECU (multiplex network body ECU) ·
Air conditioning amplifier assembly ·
Certification ECU (smart key ECU assembly) |
·
When a remote communication usage application is performed (customize or remote diagnosis), the information is processed regardless of whether the main body ECU (multiplex network body ECU) has permitted or prohibited remote communication. ·
3 retries are performed (including the first time). |
- | U0073
(Radio and display receiver assembly) |
| Meter-linked Function (for Radio and Display Type with Dual Knob Type)
·
Changes display based on customization information set through the meter. Outputs the customization information set in the system. |
Radio and display receiver assembly | Combination meter assembly | Maintains the last valid state. | - | U0073
U0155 (Radio and display receiver assembly) |
| Information Sound Control Function (for Radio and Display Type with Dual Knob Type)
·
Receives flags from the forward recognition camera to operate the alarm and mutes multi-media audio while the alarm is in operation. |
Radio and display receiver assembly | ·
Forward recognition camera ·
Clearance warning ECU assembly |
Audio mute is canceled. | - | U0073
(Radio and display receiver assembly) |
| Rear View Monitor System (for Radio and Display Type with Dual Knob Type)
·
Displays images from the rear view camera. |
Radio and display receiver assembly | ECM | Screen does not change to the camera screen. | - | - |
| Air Conditioning Control (for Radio and Display Type with Single Knob Type)
·
Controls air conditioning functions such as set temperature adjustment, air outlet selection, etc. by operating display audio controller or Remote Touch. |
Radio and display receiver assembly | Air conditioning amplifier assembly | ·
Air conditioning system indicators turn off. ·
If set temperature is shown on multi-information display or multi-display, set temperature display turns off. |
Displays messages on the multi-information display. | U016487
U100049 (Radio and display receiver assembly) |
| HV Energy Flow Display (for Radio and Display Type with Single Knob Type)
·
Creates energy flow screen which indicates regeneration status and drive force transmission status. |
Radio and display receiver assembly | Hybrid vehicle control ECU | If communication stops while the energy flow screen is displayed, the energy flow display disappears and the latest value is maintained for the SOC (state of charge) level display. | - | U029387
U100049 (Radio and display receiver assembly) |
| Destination Identification (for Radio and Display Type with Single Knob Type)
·
Identifies destination based on destination and destination package information, and selects the time zone and language used for the display. |
Radio and display receiver assembly | Main body ECU (multiplex network body ECU) | Determines the destination according to the last received value and operates accordingly (if there is no last received value, the system operates using the default value). | Time zone and language selection screen are different from actual destination. | U014087
U100049 (Radio and display receiver assembly) |
| Vehicle Customize Function (for Radio and Display Type with Single Knob Type)
·
Changes the behavior and control parameters of various functions (illumination lighting time, etc.) according to the user operation via the screen. |
Radio and display receiver assembly | ·
Main body ECU (multiplex network body ECU) ·
Air conditioning amplifier assembly ·
Certification ECU (smart key ECU assembly) |
·
When a remote communication usage application is performed (customize or remote diagnosis), the information is processed regardless of whether the main body ECU (multiplex network body ECU) has permitted or prohibited remote communication. ·
3 retries are performed (including the first time). |
- | U100049
(Radio and display receiver assembly) |
| Meter-linked Function (for Radio and Display Type with Single Knob Type)
·
Changes display based on customization information set through the meter. Outputs the customization information set in the system. |
Radio and display receiver assembly | Combination meter assembly | Maintains the last valid state. | - | U015587
U100049 (Radio and display receiver assembly) |
| Information Sound Control Function (for Radio and Display Type with Single Knob Type)
·
Receives flags from the forward recognition camera to operate the alarm and mutes multi-media audio while the alarm is in operation. |
Radio and display receiver assembly | ·
Forward recognition camera ·
Clearance warning ECU assembly |
Audio mute is canceled. | - | U100049
(Radio and display receiver assembly) |
| Rear View Monitor System (for Radio and Display Type with Single Knob Type)
·
Displays images from the rear view camera. |
Radio and display receiver assembly | ECM | Screen does not change to the camera screen. | - | - |
| Destination Determination Function
·
Judges the destination and uses the information for an operation condition for the app. ·
Judges the handle position and uses the information for an operation condition for the app. |
Clearance warning ECU assembly | Main body ECU (Multiplex network body ECU) | It operates according to previous EEPROM values when a communication stop occurs. | App stops operating (displays a warning message in the combination meter and sounds the buzzer). | U014087
(Clearance warning ECU assembly) |
| Shift position judgment
·
Is used as an operation condition for the app. |
Clearance warning ECU assembly | Hybrid vehicle control ECU | Changes to an operation state which is used when the shift lever is in P. | App stops operating (displays a warning message in the combination meter and sounds the buzzer). | U029387
(Clearance warning ECU assembly) |
| Engine Model Information
·
Judges the engine/transmission model and switches the control constant table. ·
Is used as an operation condition for the app. ·
Determines whether the vehicle is 2WD or AWD and switches the steering parameter table. |
Clearance warning ECU assembly | Hybrid vehicle control ECU | It operates according to previous EEPROM values when a communication stop occurs. | App stops operating (displays a warning message in the combination meter and sounds the buzzer). | U029387
(Clearance warning ECU assembly) |
| Engine Control State Information
·
Judges whether the engine is on or off. ·
Is used as an operation condition for the app. |
Clearance warning ECU assembly | ECM | App stops operating (displays a warning message in the combination meter and sounds the buzzer). | App stops operating (displays a warning message in the combination meter and sounds the buzzer). | U029387
(Clearance warning ECU assembly) |
| During CSR Request Operation G
·
Is used as an operation condition for the app. |
Clearance warning ECU assembly | Hybrid vehicle control ECU | App stops operating (displays a warning message in the combination meter and sounds the buzzer). | App stops operating (displays a warning message in the combination meter and sounds the buzzer). | U029387
(Clearance warning ECU assembly) |
| Cruise Control Information
·
Is used as an operation condition for the app. |
Clearance warning ECU assembly | Hybrid vehicle control ECU | App stops operating (displays a warning message in the combination meter and sounds the buzzer). | App stops operating (displays a warning message in the combination meter and sounds the buzzer). | U029387
(Clearance warning ECU assembly) |
| HV System Information
·
Is used as an operation condition for the app. |
Clearance warning ECU assembly | Hybrid vehicle control ECU | App stops operating (displays a warning message in the combination meter and sounds the buzzer). | App stops operating (displays a warning message in the combination meter and sounds the buzzer). | U029387
(Clearance warning ECU assembly) |
| Accelerator Opening Angle
·
Is used as an operation condition for the app. |
Clearance warning ECU assembly | Hybrid vehicle control ECU | App stops operating (displays a warning message in the combination meter and sounds the buzzer). | App stops operating (displays a warning message in the combination meter and sounds the buzzer). | U029387
(Clearance warning ECU assembly) |
| Power Steering Control Information
·
Is used as an operation condition for the app. |
Clearance warning ECU assembly | Power steering ECU assembly | App stops operating (displays a warning message in the combination meter and sounds the buzzer). | App stops operating (displays a warning message in the combination meter and sounds the buzzer). | U013187
(Clearance warning ECU assembly) |
| Turn Light Condition
·
Is used as an operation condition for the app. |
Clearance warning ECU assembly | Combination meter assembly | App stops operating (displays a warning message in the combination meter and sounds the buzzer). | App stops operating (displays a warning message in the combination meter and sounds the buzzer). | U015587
(Clearance warning ECU assembly) |
| Clearance Sonar Main Switch Information
·
Is used as an operation condition for the clearance warning ECU assembly. |
Clearance warning ECU assembly | Combination meter assembly | App stops operating (displays a warning message in the combination meter and sounds the buzzer). | App stops operating (displays a warning message in the combination meter and sounds the buzzer). | U015587
(Clearance warning ECU assembly) |
| Clearance Sonar Buzzer Mute/Volume Change
·
Is used as an operation condition for the clearance warning ECU assembly. |
Clearance warning ECU assembly | Combination meter assembly | App stops operating (displays a warning message in the combination meter and sounds the buzzer). | App stops operating (displays a warning message in the combination meter and sounds the buzzer). | U015587
(Clearance warning ECU assembly) |
| Data Continuity (Valid/Invalid) Flag
+B Open Circuit Malfunction Sensor Malfunction Steering Angle Signal Sensor Internal Zero Point Memorization Invalid/Valid Steering Angle Sensor Internally Memorized Zero Point Value Steering sensor Calculated Value ·
Is used as an operation condition for the app. |
Clearance warning ECU assembly | Steering sensor | App stops operating (displays a warning message in the combination meter and sounds the buzzer). | App stops operating (displays a warning message in the combination meter and sounds the buzzer). | U012687
(Clearance warning ECU assembly) |
| Wheel Speed Information
·
The wheel speed signal from each wheel (after 1/2 filter) is used to calculate the vehicle speed. |
Clearance warning ECU assembly | Brake booster with master cylinder assembly | App stops operating (displays a warning message in the combination meter and sounds the buzzer). | App stops operating (displays a warning message in the combination meter and sounds the buzzer). | U012987
(Clearance warning ECU assembly) |
| Wheel Speed Sensor State Information, Wheel Speed Calculated Value
·
Is used as an operation condition for the app. |
Clearance warning ECU assembly | Brake booster with master cylinder assembly | App stops operating (displays a warning message in the combination meter and sounds the buzzer). | App stops operating (displays a warning message in the combination meter and sounds the buzzer). | U012987
(Clearance warning ECU assembly) |
| Master Cylinder Pressure Malfunction Flag
Master Cylinder Pressure Invalid Flag Master Cylinder Pressure BA Fail Signal STP Switch Signal STP Switch Open Circuit Signal During VSC Control During ABS Control ·
Is used as an operation condition for the app. |
Clearance warning ECU assembly | Brake booster with master cylinder assembly | App stops operating (displays a warning message in the combination meter and sounds the buzzer). | App stops operating (displays a warning message in the combination meter and sounds the buzzer). | U012987
(Clearance warning ECU assembly) |
| TRC Operating Flag
·
Is used as an operation condition for the app. |
Clearance warning ECU assembly | Brake booster with master cylinder assembly | App stops operating (displays a warning message in the combination meter and sounds the buzzer). | App stops operating (displays a warning message in the combination meter and sounds the buzzer). | U012987
(Clearance warning ECU assembly) |
| Brake Control State Signal
·
Is used as an operation condition for the app. |
Clearance warning ECU assembly | Brake booster with master cylinder assembly | App stops operating (displays a warning message in the combination meter and sounds the buzzer). | App stops operating (displays a warning message in the combination meter and sounds the buzzer). | U012987
(Clearance warning ECU assembly) |
| Yaw Rate Sensor State Signal
·
Is used as an operation condition for the app. |
Clearance warning ECU assembly | Brake booster with master cylinder assembly | App stops operating (displays a warning message in the combination meter and sounds the buzzer). | App stops operating (displays a warning message in the combination meter and sounds the buzzer). | U012987
(Clearance warning ECU assembly) |
| Speed Information Signal for Each Wheel
·
Calculates the amount of movement. |
Clearance warning ECU assembly | Brake booster with master cylinder assembly | App stops operating (displays a warning message in the combination meter and sounds the buzzer). | App stops operating (displays a warning message in the combination meter and sounds the buzzer). | U012987
(Clearance warning ECU assembly) |
| VSC OFF, TRC OFF Indicator
·
Is used as an operation condition for the app. |
Clearance warning ECU assembly | Brake booster with master cylinder assembly | App stops operating (displays a warning message in the combination meter and sounds the buzzer). | App stops operating (displays a warning message in the combination meter and sounds the buzzer). | U012987
(Clearance warning ECU assembly) |
| Yaw Rate Sensor State Signal
·
Is used as an operation condition for the app. |
Clearance warning ECU assembly | Airbag sensor assembly | App stops operating (displays a warning message in the combination meter and sounds the buzzer). | App stops operating (displays a warning message in the combination meter and sounds the buzzer). | U012587
(Clearance warning ECU assembly) |
| Power Steering Control
·
Calculates assist current according to torque sensor value and vehicle speed and drives motor. |
Power steering ECU assembly | ·
ECM ·
Hybrid vehicle control ECU ·
Brake booster with master cylinder assembly ·
Airbag sensor assembly ·
Steering sensor |
·
Control is performed temporarily with the steering assist amount set to that used when the vehicle speed is 100 km/h (62 mph). ·
Zero point learning is not performed. ·
Drivability degrades (compensation control using steering angle is stopped). |
EPS warning light illuminates. | U0100
U0129 U0293 (Power steering ECU assembly) |
| Assist Map Selection
·
Selects proper assist map according to destination, engine type, etc. |
Power steering ECU assembly | ECM | Default map is used to assist because proper assist map cannot be selected. (Steering feel may be different.) | EPS warning light illuminates. | C1581
(Power steering ECU assembly) |
| VDIMα System
·
Calculates current to be used for steering assist according to commanded value from VSC, and then operates motor. |
Power steering ECU assembly | Brake booster with master cylinder assembly | VDIMα control is stopped. | - | U0129
(Power steering ECU assembly) |
| Engine/Hybrid Toggle
·
So that the same parts can be used for conventional and hybrid vehicles, this toggles the communication type. |
Power steering ECU assembly | ECM | Control is performed temporarily with the steering assist amount set to that used when the vehicle speed is 100 km/h (62 mph). | EPS warning light illuminates. | U0293
(Power steering ECU assembly) |
| MG ECU
·
Cooperative control between the inverter with converter assembly and ECM. |
ECM | Inverter with converter assembly | Engine is stopped. | MIL illuminates. | U011087
(ECM) |
| HV ECU
·
Cooperative control between the hybrid vehicle control ECU and ECM. |
ECM | Hybrid vehicle control ECU | Engine is stopped. | MIL illuminates. | U029387
U129387 (ECM) |
| Headlight Leveling Control (Headlight Control)
·
Adjusts headlights vertical aiming according to wheel speed and vehicle pitch angle determined using vehicle height sensor. |
Headlight ECU sub-assembly LH | ·
Brake booster with master cylinder assembly ·
Main body ECU (multiplex network body ECU) |
Control stops. | - | U0129
U0142 (Headlight ECU sub-assembly LH) |
| Destination Identification
·
Checks if the destination information stored in the headlight ECU sub-assembly LH and the destination information data transmitted in the CAN bus lines are the same. |
Headlight ECU sub-assembly LH | ·
ECM ·
Main body ECU (multiplex network body ECU) |
- | - | U0100
U0142 (Headlight ECU sub-assembly LH) |
| Low Beam Headlights, High Beam Headlights, Clearance Lights and Side Marker Lights
·
Turns the specified light source on and off according to low beam, high beam command data. |
Main body ECU (multiplex network body ECU) | Headlight ECU sub-assembly LH | The low beam headlights, clearance lights and side marker lights are forcibly illuminated. | - | U0142
(Headlight ECU sub-assembly LH) |
| LED Headlight Indicator
·
Monitors low beam LED malfunctions and when a malfunction is detected, sends an indicator illumination request to the meter. |
Headlight ECU sub-assembly LH | Combination meter assembly | Maintains the LED headlight indicator status. | ·
Buzzer sounds. ·
Displays messages on the multi-information display. |
U0073
U1000 (Headlight ECU sub-assembly LH) |
| Headlight Cleaner Signal Output
·
Outputs the headlight cleaner relay ON signal based on the direct line front washer switch signals, headlight cleaner switch signals, low beam illumination command from the main body ECU (multiplex network body ECU) and IG data. |
Headlight ECU sub-assembly LH | Combination meter assembly | Stops headlight cleaner operation. | - | U0142
(Headlight ECU sub-assembly LH) |
| Door Lock
·
Controls key linked and automatic door lock/unlock function, key confinement prevention function, etc. |
Main body ECU (multiplex network body ECU) | Airbag sensor assembly | Key linked door lock/unlock function is performed even when the power switch is on (IG) and the driver seatbelt is fastened. | - | U0151
(Main body ECU (multiplex network body ECU)) |
| Alarm
·
Sounds various warnings. |
Main body ECU (multiplex network body ECU) | ·
ECM ·
Hybrid vehicle control ECU ·
Certification ECU (smart key ECU assembly) |
- | - | U0100
U0120 U0293 (Main body ECU (multiplex network body ECU)) |
| Automatic Dimming of Display
·
Controls display dimming control. |
Main body ECU (multiplex network body ECU) | Combination meter assembly | Automatically performs display dimming control when tail mode is not canceled (when the light sensor illuminance signal value is less than the display dimming value, the interior displays and indicators are dimmed). | - | U0155
(Main body ECU (multiplex network body ECU)) |
| Illumination
·
Performs illumination control. |
Main body ECU (multiplex network body ECU) | ·
Certification ECU (smart key ECU assembly) ·
ECM |
·
The dome light turns off. ·
The outside handle illumination turns off. ·
The foot light is adjusted. |
The dome light does not turn off immediately after exiting the vehicle. | U0101
U0327 (Main body ECU (multiplex network body ECU)) |
| Diagnostic/C-BEST
·
Diagnostic phase 4 communication. |
- | All ECUs connected to CAN | Exits diagnostic mode. | - | - |
| Entry and Start Function/Wireless
·
Controls entry and start function/wireless functions. |
Certification ECU (smart key ECU assembly) | Certification ECU (smart key ECU assembly) | Entry lock/unlock control not possible. | - | U0327
(Main body ECU (multiplex network body ECU)) |
| Lighting Control
·
Controls the daytime running lights |
Main body ECU (multiplex network body ECU) | ·
ECM ·
Hybrid vehicle control ECU ·
Brake actuator assembly |
Daytime running light control is not performed. | - | U0100
U0293 U1106 (Main body ECU (multiplex network body ECU)) |
| Automatic High Beam
·
Detects oncoming traffic, vehicles ahead, street lights, etc. using an onboard sensor and automatically turns the high beam lights on and off |
Main body ECU (multiplex network body ECU) | ·
Headlight ECU sub-assembly LH ·
Forward recognition camera |
The system does not operate. | ·
Buzzer sounds. ·
Displays messages on the multi-information display. |
U0182
U023A (Main body ECU (multiplex network body ECU)) |
| Lighting Control
·
The headlight ECU controls the loading around the headlights (body ECU sends an illumination request to headlight ECU) |
Headlight ECU sub-assembly LH | Main body ECU (multiplex network body ECU) | - | ·
Buzzer sounds. ·
Displays messages on the multi-information display. |
U0182
(Main body ECU (multiplex network body ECU)) |
| Lighting Control
·
European headlight auto-cut |
Main body ECU (multiplex network body ECU) | Brake booster with master cylinder assembly | Maintains previous values. | - | U0129
(Main body ECU (multiplex network body ECU)) |
| Panoramic View Monitor
·
Shows an overhead map along with front, side and rear images on the display. ·
Shows guide lines on the displayed image in tandem with the steering angle. ·
Displays the clearance sonar detection area. ·
Displays the RCTA detection conditions. |
Parking assist ECU | ·
Steering sensor ·
Brake actuator assembly ·
ECM ·
Main body ECU (multiplex network body ECU) ·
Clearance warning ECU assembly ·
Blind spot monitor sensor LH ·
Radio and Display Receiver Assembly |
·
An alert mark is displayed. ·
The guide lines (linked lines) are not displayed. ·
Distance guide line 3 (the fixed guide line) is displayed in red. ·
The guide lines (fixed lines) are not displayed. ·
The clearance sonar icon is not displayed. ·
The RCTA icon is not displayed. ·
Soft switch is grayed out. ·
Language switching works with stored values. ·
It operates according to previous values of vehicle information. ·
The camera screen display is stopped (however, the displaying of images that comply with regulations continues). ·
Nothing is displayed, except for images that comply with regulations. ·
The screen display is stopped when the front mode screen is displayed. ·
It operates as if the mirrors are open. ·
Screen design operates according to previous values. |
·
An alert mark is displayed on the top of the camera screen. ·
The clearance sonar icon is not displayed. ·
The RCTA icon is not displayed. |
U0073
U0100 U0126 U0129 U0140 U0163 U0233 U0265 U1110 (Parking assist ECU) |