Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for Radio and Display Type with Dual Knob Type) › from 2022.01
RM32K0E _56 Audio / Visual / Telematics _061290 NAVIGATION / MULTI INFO DISPLAY _0524476 NAVIGATION SYSTEM(for Radio and Display Type with Dual Knob Type) C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Radio and Display Type with Dual Knob Type)  B153A  GVIF Disconnected (from Extension Module to H/U)  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area
B153A GVIF Disconnected (from Extension Module to H/U) GVIF disconnected (from navigation ECU to radio and display receiver assembly)
·

Navigation ECU

·

Radio and display receiver assembly

·

Harness or connector

·

No. 1 Navigation Wire*



*: for TMC Made


WIRING DIAGRAM

E402230E08
1.281,0.844 1.719,1.083 0.438,0.24 10 false GVO+ 0.802,2.177 1.24,2.417 0.438,0.24 10 false j6 0.781,2.365 1.823,2.615 1.042,0.25 10 false Navigation ECU 0.885,3.385 1.865,3.625 0.979,0.24 10 false : GVIF Cable 1.854,0.719 2.292,0.958 0.438,0.24 10 false 2 1.854,1.177 2.292,1.417 0.438,0.24 10 false 1 1.854,1.656 2.292,1.896 0.438,0.24 10 false 3 1.323,1.292 1.76,1.531 0.438,0.24 10 false GVO- 1.313,1.74 1.75,1.979 0.438,0.24 10 false GVG1 5.458,0.854 5.896,1.094 0.438,0.24 10 false GV2+ 5.469,1.281 5.906,1.521 0.438,0.24 10 false GV2- 5.479,1.74 5.917,1.979 0.438,0.24 10 false GVG2 5.313,2.167 5.75,2.406 0.438,0.24 10 false j7 5.292,2.365 7.01,3.021 1.719,0.656 10 false Radio and Display Receiver Assembly 5.219,1.646 5.656,1.885 0.438,0.24 10 false 3 5.208,1.177 5.646,1.417 0.438,0.24 10 false 1 5.198,0.729 5.635,0.969 0.438,0.24 10 false 2 5.125,3.333 7.063,3.521 1.938,0.188 10 false *: Shielded 3.552,1.667 4.042,1.792 0.49,0.125 10 false * 0.177,0.125 1.906,0.479 1.729,0.354 12 false for TMMT Made:

E425814E02
1.281,0.844 1.719,1.083 0.438,0.24 10 false GVO+ 0.802,2.177 1.24,2.417 0.438,0.24 10 false k3 0.781,2.365 1.823,2.615 1.042,0.25 10 false Navigation ECU 0.917,3.375 1.896,3.615 0.979,0.24 10 false : GVIF Cable 1.854,0.719 2.292,0.958 0.438,0.24 10 false 2 1.854,1.177 2.292,1.417 0.438,0.24 10 false 1 1.854,1.656 2.292,1.896 0.438,0.24 10 false 3 1.323,1.292 1.76,1.531 0.438,0.24 10 false GVO- 1.313,1.74 1.75,1.979 0.438,0.24 10 false GVG1 5.458,0.854 5.896,1.094 0.438,0.24 10 false GV2+ 5.469,1.281 5.906,1.521 0.438,0.24 10 false GV2- 5.479,1.74 5.917,1.979 0.438,0.24 10 false GVG2 5.313,2.167 5.75,2.406 0.438,0.24 10 false j7 5.292,2.365 7.01,3.021 1.719,0.656 10 false Radio and Display Receiver Assembly 5.219,1.646 5.656,1.885 0.438,0.24 10 false 3 5.208,1.177 5.646,1.417 0.438,0.24 10 false 1 5.198,0.729 5.635,0.969 0.438,0.24 10 false 2 5.125,3.333 7.063,3.521 1.938,0.188 10 false *: Shielded 3.552,1.667 4.042,1.792 0.49,0.125 10 false * 0.177,0.125 1.906,0.479 1.729,0.354 12 false for TMC Made: 2.813,2.24 4.75,2.427 1.938,0.188 10 false No. 1 Navigation Wire

CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM (for Radio and Display Type with Dual Knob Type)>PRECAUTION


PROCEDURE

1.CHECK DTC
a.

Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs
50002 212

b.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Result Proceed to
OK A
NG (for TMMT Made) B
NG (for TMC Made) C



A

B

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NAVIGATION ECU)

C

5.INSPECT NO. 1 NAVIGATION WIRE
2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NAVIGATION ECU)
a.
E368007C49
1.49,0.5 1.906,0.75 0.417,0.25 1.479,2.667 1.896,2.917 0.417,0.25 1.823,1.302 2.24,0.885 true 1.625,1.333 1.135,0.885 true 1.656,1.469 1.396,1.917 true 1.448,3.615 1.188,4.063 true 1.542,3.458 1.99,4 true 1.417,3.438 0.927,2.99 true 0.271,0.146 0.583,0.302 0.313,0.156 10 false *a 0.323,2.448 0.635,2.604 0.313,0.156 10 false *b 1.615,0.542 2.083,0.792 0.469,0.25 10 false j7 1.583,2.708 2.115,3 0.531,0.292 10 false j6 2.115,0.688 2.688,0.917 0.573,0.229 10 false GV2+ 0.896,0.708 1.469,0.938 0.573,0.229 10 false GV2- 1.115,1.969 1.688,2.198 0.573,0.229 10 false GVG2 0.938,4.104 1.51,4.333 0.573,0.229 10 false GVG1 0.719,2.823 1.292,3.052 0.573,0.229 10 false GVO- 1.802,4.073 2.375,4.302 0.573,0.229 10 false GVO+
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)
*b Front view of wire harness connector
(to Navigation ECU)


Disconnect the j6 navigation ECU connector.


b.

Disconnect the j7 radio and display receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
j6-1 (GVO-) - j7-1 (GV2-) Always Below 1 Ω
j6-2 (GVO+) - j7-2 (GV2+) Always Below 1 Ω
j6-3 (GVG1) - j7-3 (GVG2) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.REPLACE NAVIGATION ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.REPLACE NAVIGATION ECU
a.

Replace the navigation ECU with a new or known good one.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

4.CHECK DTC
4.CHECK DTC
a.

Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs
50002 212

b.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END (NAVIGATION ECU IS DEFECTIVE)

NG

5.INSPECT NO. 1 NAVIGATION WIRE
a.
E368007C50
1.49,0.5 1.906,0.75 0.417,0.25 1.479,2.667 1.896,2.917 0.417,0.25 1.823,1.302 2.24,0.885 true 1.625,1.333 1.135,0.885 true 1.656,1.469 1.396,1.917 true 1.448,3.615 1.188,4.063 true 1.542,3.458 1.99,4 true 1.417,3.438 0.927,2.99 true 0.271,0.146 0.583,0.302 0.313,0.156 10 false *a 0.323,2.448 0.635,2.604 0.313,0.156 10 false *b 1.615,0.531 2.083,0.781 0.469,0.25 10 false j7 1.594,2.708 2.125,3 0.531,0.292 10 false k3 2.115,0.688 2.688,0.917 0.573,0.229 10 false GV2+ 0.896,0.708 1.469,0.938 0.573,0.229 10 false GV2- 1.115,1.969 1.688,2.198 0.573,0.229 10 false GVG2 0.938,4.104 1.51,4.333 0.573,0.229 10 false GVG1 0.719,2.823 1.292,3.052 0.573,0.229 10 false GVO- 1.802,4.073 2.375,4.302 0.573,0.229 10 false GVO+
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)
*b Front view of wire harness connector
(to Navigation ECU)


Disconnect the k3 navigation ECU connector.


b.

Disconnect the j7 radio and display receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
k3-1 (GVO-) - j7-1 (GV2-) Always Below 1 Ω
k3-2 (GVO+) - j7-2 (GV2+) Always Below 1 Ω
k3-3 (GVG1) - j7-3 (GVG2) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.REPLACE NAVIGATION ECU

NG

REPLACE NO. 1 NAVIGATION WIRE

6.REPLACE NAVIGATION ECU
a.

Replace the navigation ECU with a new or known good one.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

7.CHECK DTC
7.CHECK DTC
a.

Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs
50002 212

b.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END (NAVIGATION ECU IS DEFECTIVE)

NG