Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for Radio and Display Type with Dual Knob Type) › from 2022.01
RM32K0E _56 Audio / Visual / Telematics _061290 NAVIGATION / MULTI INFO DISPLAY _0524476 NAVIGATION SYSTEM(for Radio and Display Type with Dual Knob Type) C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Radio and Display Type with Dual Knob Type)  B1579  Voice Recognition Microphone Disconnected  


DESCRIPTION

The radio and display receiver assembly and map light assembly (telephone microphone assembly) are connected to each other using the microphone connection detection signal lines.

This DTC is stored when a microphone connection detection signal line is disconnected.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1579 Voice Recognition Microphone Disconnected Telephone microphone signal is lost.
·

Map light assembly (telephone microphone assembly)

·

Radio and display receiver assembly

·

Harness or connector



WIRING DIAGRAM

for TMMT Made
E360100E02
4.906,2.188 6.594,2.76 1.688,0.573 10 false Radio and Display Receiver Assembly 4.927,2.01 5.542,2.208 0.615,0.198 10 false F131 5.083,1.542 5.698,1.74 0.615,0.198 10 false MIN- 5.073,0.708 5.688,0.906 0.615,0.198 10 false SNS2 4.813,1.385 5.125,1.583 0.313,0.198 10 false 22 4.833,0.594 5.146,0.792 0.313,0.198 10 false 25 2.146,0.583 2.458,0.781 0.313,0.198 10 false 1 2.167,1.375 2.479,1.573 0.313,0.198 10 false 7 1.646,1.479 2.365,1.719 0.719,0.24 10 false MCO- 1.677,0.698 2.396,0.938 0.719,0.24 10 false SNS2 0.865,2.156 2.865,2.76 2,0.604 10 false Map Light Assembly (Telephone Microphone Assembly) 0.875,2 1.49,2.198 0.615,0.198 10 false R2

for TMC Made
E431708E01
4.938,1.802 6.625,2.375 1.688,0.573 10 false Radio and Display Receiver Assembly 4.938,1.615 5.552,1.813 0.615,0.198 10 false F131 5.094,1 5.708,1.198 0.615,0.198 10 false MIN- 5.073,0.563 5.688,0.76 0.615,0.198 10 false SNS2 4.833,0.917 5.146,1.115 0.313,0.198 10 false 22 4.833,0.438 5.146,0.635 0.313,0.198 10 false 25 2.552,0.458 2.865,0.656 0.313,0.198 10 false 1 2.552,0.906 2.865,1.104 0.313,0.198 10 false 7 2.063,0.906 2.781,1.146 0.719,0.24 10 false MCO- 2.01,0.427 2.729,0.667 0.719,0.24 10 false SNS2 0.396,2.292 2.146,2.521 1.75,0.229 10 false Map Light Assembly 0.427,2.125 1.042,2.323 0.615,0.198 10 false R2 0.406,1.573 2.792,2.094 2.385,0.521 10 false Telephone Microphone Assembly 0.417,1.406 0.729,1.604 0.313,0.198 10 false B 1.448,0.448 1.76,0.646 0.313,0.198 10 false 1 1.458,0.896 1.771,1.094 0.313,0.198 10 false 2

PROCEDURE

1.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
a.
E426527C03
1.458,0.521 1.875,0.813 0.417,0.292 2.042,2.135 2.365,2.667 true 0.146,0.135 0.458,0.333 0.313,0.198 10 false *a 1.51,0.583 1.917,0.823 0.406,0.24 10 false F131 2.396,2.635 2.802,2.875 0.406,0.24 10 false MIN-
*a Component with harness connected
(Radio and Display Receiver Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F131-22 (MIN-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.CONFIRM MODEL

NG

2.CONFIRM MODEL
a.

Choose the model to be inspected.

Result:
Result Proceed to
for TMMT Made A
for TMC Made B




A

3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))

B

5.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))
a.

Disconnect the F131 radio and display receiver assembly connector.


b.

Disconnect the R2 map light assembly (telephone microphone assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F131-25 (SNS2) - R2-1 (SNS2) Always Below 1 Ω
F131-22 (MIN-) - R2-7 (MCO-) Always Below 1 Ω
F131-25 (SNS2) - Body ground Always 10 kΩ or higher
F131-22 (MIN-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)
a.

Remove the map light assembly (telephone microphone assembly).


b.
E358190C03
2.302,1.094 2.719,0.677 true 2.281,1.438 2.625,1.781 true 0.177,0.156 0.49,0.354 0.313,0.198 10 false *a 2.792,0.521 3.229,0.802 0.438,0.281 10 false SNS2 2.698,1.74 3.167,2.042 0.469,0.302 10 false MCO-
*a Component without harness connected
(Map Light Assembly (Telephone Microphone Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (SNS2) - 7 (MCO-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPLACE MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

5.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)
a.

Disconnect the F131 radio and display receiver assembly connector.


b.

Disconnect the R2 map light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F131-25 (SNS2) - R2-1 (SNS2) Always Below 1 Ω
F131-22 (MIN-) - R2-7 (MCO-) Always Below 1 Ω
F131-25 (SNS2) - Body ground Always 10 kΩ or higher
F131-22 (MIN-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT TELEPHONE MICROPHONE ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT TELEPHONE MICROPHONE ASSEMBLY
a.

Remove the telephone microphone assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>MICROPHONE>REMOVAL


b.
E339287C01
1.75,1.75 1.969,1.313 true 2.75,1.75 2.531,1.302 true 0.167,0.177 0.479,0.333 0.313,0.156 10 false *a 1.604,1.813 2.219,2.01 0.615,0.198 10 false MIC- 2.646,1.813 3.26,2.01 0.615,0.198 10 false SNS2
*a Component without harness connected
(Telephone Microphone Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (SNS2) - 2 (MIC-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

7.INSPECT MAP LIGHT ASSEMBLY

NG

REPLACE TELEPHONE MICROPHONE ASSEMBLY

7.INSPECT MAP LIGHT ASSEMBLY
a.

b.

Remove the telephone microphone assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>MICROPHONE>REMOVAL


c.
E431698C01
1.51,1.792 1.906,2.052 0.396,0.26 1.458,0.188 1.854,0.448 0.396,0.26 2.104,1.229 2.667,1.115 true 2.521,0.594 2.083,1 true 1.552,0.229 2.01,0.427 0.458,0.198 10 false R2 1.635,1.844 2.094,2.042 0.458,0.198 10 false B 2.594,0.469 3.208,0.667 0.615,0.198 10 false SNS2 2.719,1.021 3.333,1.219 0.615,0.198 10 false MCO- 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 0.156,1.792 0.469,1.99 0.313,0.198 10 false *b
*a Component without harness connected
(Map Light Assembly)
*b Component without harness connected
(Telephone Microphone Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R2-1 (SNS2) - B-1 Always Below 1 Ω
R2-7 (MCO-) - B-2 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG