Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for Radio and Display Type with Dual Knob Type) › from 2022.01
RM32K0E _56 Audio / Visual / Telematics _061290 NAVIGATION / MULTI INFO DISPLAY _0524476 NAVIGATION SYSTEM(for Radio and Display Type with Dual Knob Type) C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Radio and Display Type with Dual Knob Type)  B15C2  Speed Signal Malfunction  


DESCRIPTION

The navigation ECU receives a vehicle speed signal from the combination meter assembly and information from the navigation antenna assembly, and then adjusts the vehicle position on the map.

The navigation ECU stores this DTC when the difference between the speed information that the navigation antenna assembly receives and the SPD pulse received from the combination meter assembly becomes large.

HINT:
·

A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly. The signal is changed to a pulse signal at the transistor in the combination meter assembly. Each ECU controls its respective system based on this pulse signal.

·

If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the following diagram will not operate normally.



DTC No. Detection Item DTC Detection Condition Trouble Area
B15C2 Speed Signal Malfunction A difference between the GPS speed and SPD pulse is detected
·

Meter / gauge system

·

Navigation ECU

·

Radio and display receiver assembly

·

Harness or connector



WIRING DIAGRAM

E368000E41
2.427,1.104 2.885,1.302 0.458,0.198 10 false 6 2.125,1.208 2.583,1.406 0.458,0.198 10 false +S 4.625,1.094 5.083,1.292 0.458,0.198 10 false 9 4.833,1.198 5.292,1.396 0.458,0.198 10 false SPD 4.865,2.031 5.323,2.229 0.458,0.198 10 false n2 4.854,2.188 5.958,2.479 1.104,0.292 10 false Navigation ECU 1.031,2.021 1.49,2.219 0.458,0.198 10 false F4 1.021,2.188 3.042,2.531 2.021,0.344 10 false Combination Meter Assembly 0.135,0.125 1.583,0.365 1.448,0.24 12 false for TMMT Made:

E368000E42
2.427,1.104 2.885,1.302 0.458,0.198 10 false 6 2.125,1.208 2.583,1.406 0.458,0.198 10 false +S 4.625,1.094 5.083,1.292 0.458,0.198 10 false 9 4.833,1.198 5.292,1.396 0.458,0.198 10 false SPD 4.865,2.031 5.323,2.229 0.458,0.198 10 false F168 4.854,2.188 5.958,2.479 1.104,0.292 10 false Navigation ECU 1.031,2.021 1.49,2.219 0.458,0.198 10 false F4 1.021,2.188 3.042,2.531 2.021,0.344 10 false Combination Meter Assembly 0.177,0.156 2.167,0.396 1.99,0.24 12 false for TMC Made:

CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM (for Radio and Display Type with Dual Knob Type)>PRECAUTION


PROCEDURE

1.CHECK DTC
a.

Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs
50002 212

b.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK VEHICLE SENSOR (OPERATION CHECK)
2.CHECK VEHICLE SENSOR (OPERATION CHECK)
a.
E276610

Enter the "System Sensors Check" screen. Refer to Check GPS & Vehicle Sensors in Operation Check.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM (for Radio and Display Type with Dual Knob Type)>OPERATION CHECK


b.

While driving the vehicle, compare the value of "SPEED" indicator to the reading on the speedometer. Check if these readings are almost equal.

HINT:

The combination meter assembly receives the vehicle speed signal from the skid control ECU via CAN communication. Therefore, perform the following procedure inspection referring to values in the Data List of the skid control ECU because it is the source of the vehicle speed signal.


OK:

Vehicle speed displayed on the "System Sensors Check" screen is almost the same as the actual vehicle speed measured using the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST



Result:
Proceed to
OK
NG



OK

5.REPLACE NAVIGATION ECU

NG

3.CHECK COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)
3.CHECK COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)
a.
E393685C44
1.469,0.333 1.969,0.583 0.5,0.25 2.469,1.969 2.188,1.354 true 0.188,0.188 0.5,0.385 0.313,0.198 10 false *a 1.615,0.365 2.073,0.563 0.458,0.198 10 false F4 2.417,1.979 2.729,2.177 0.313,0.198 10 false +S 2.771,3.594 3.229,3.792 0.458,0.198 10 false GND 1.115,3.844 1.271,4.042 0.156,0.198 10 false A
*a Component with harness connected
(Combination Meter Assembly)


Check the output waveform.

i.

Remove the combination meter assembly with the connector(s) still connected.


ii.

Connect an oscilloscope to terminal F4-6 (+S) and body ground.


iii.

Turn the power switch on (IG).


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal F4-6 (+S) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.




Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (NAVIGATION ECU - COMBINATION METER ASSEMBLY)

NG

4.CHECK HARNESS AND CONNECTOR (NAVIGATION ECU - COMBINATION METER ASSEMBLY)
a.

Disconnect the n2*1 or F168*2 navigation ECU connector.


b.

Disconnect the F4 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

*1: for TMMT Made

*2: for TMC Made

Standard Resistance:
for TMMT Made
Tester Connection Condition Specified Condition
n2-9 (SPD) - F4-6 (+S) Always Below 1 Ω
n2-9 (SPD) or F4-6 (+S) - Body ground Always 10 kΩ or higher


Standard Resistance:
for TMC Made
Tester Connection Condition Specified Condition
F168-9 (SPD) - F4-6 (+S) Always Below 1 Ω
F168-9 (SPD) or F4-6 (+S) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.REPLACE NAVIGATION ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE NAVIGATION ECU
a.

Replace the navigation ECU with a new or known good one.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.CHECK DTC
6.CHECK DTC
a.

Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs
50002 212

b.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END (NAVIGATION ECU IS DEFECTIVE)

NG