Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type with Dual Knob Type) › from 2022.01
RM32K0E _56 Audio / Visual / Telematics _061817 AUDIO / VIDEO _0524509 AUDIO AND VISUAL SYSTEM(for Radio and Display Type with Dual Knob Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type with Dual Knob Type)  Sound Signal Circuit between Radio Receiver and Stereo Component Amplifier  


DESCRIPTION

The radio and display receiver assembly sends a sound signal to the stereo component amplifier assembly via this circuit.

The sound signal that is sent is amplified by the stereo component amplifier assembly, and then is sent to the speakers.

If there is an open or short in this circuit, sound cannot be heard from the speakers even if the stereo component amplifier assembly or speakers are not malfunctioning.

WIRING DIAGRAM

E425794E02
0.281,3.615 1.479,4.167 1.198,0.552 10 false Radio and Display Receiver Assembly 0.281,3.458 0.781,3.698 0.5,0.24 10 false F132 5.688,3.458 6.188,3.708 0.5,0.25 10 false F152 5.677,3.625 6.896,4.156 1.219,0.531 10 false Stereo Component Amplifier Assembly 3.26,2.74 3.969,3.01 0.708,0.271 10 false (Shielded) 0.927,0.635 1.292,0.854 0.365,0.219 10 false FR+ 0.969,1.208 1.333,1.427 0.365,0.219 10 false FR- 0.948,1.833 1.313,2.052 0.365,0.219 10 false FL+ 0.969,2.427 1.333,2.646 0.365,0.219 10 false FL- 1.344,1.104 1.5,1.333 0.156,0.229 10 false 6 1.344,0.521 1.5,0.75 0.156,0.229 10 false 1 1.354,1.708 1.51,1.938 0.156,0.229 10 false 2 1.354,2.292 1.51,2.521 0.156,0.229 10 false 7 5.76,0.521 5.917,0.75 0.156,0.229 10 false 5 5.76,1.125 5.917,1.354 0.156,0.229 10 false 4 5.76,1.708 5.917,1.938 0.156,0.229 10 false 3 5.76,2.292 5.917,2.521 0.156,0.229 10 false 2 5.75,2.875 5.906,3.104 0.156,0.229 10 false 6 6,0.625 6.313,0.823 0.313,0.198 10 false R+ 6,1.24 6.313,1.438 0.313,0.198 10 false R- 6,1.813 6.313,2.01 0.313,0.198 10 false L+ 6,2.417 6.313,2.615 0.313,0.198 10 false L- 5.99,3.021 6.344,3.219 0.354,0.198 10 false SLD

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)
a.

Disconnect the F132 radio and display receiver assembly connector.


b.

Disconnect the F152 stereo component amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F152-5 (R+) - F132-1 (FR+) Always Below 1 Ω
F152-4 (R-) - F132-6 (FR-) Always Below 1 Ω
F152-3 (L+) - F132-2 (FL+) Always Below 1 Ω
F152-2 (L-) - F132-7 (FL-) Always Below 1 Ω
F152-6 (SLD) - Body ground Always 10 kΩ or higher
F152-5 (R+) or F132-1 (FR+) - Body ground Always 10 kΩ or higher
F152-4 (R-) or F132-6 (FR-) - Body ground Always 10 kΩ or higher
F152-3 (L+) or F132-2 (FL+) - Body ground Always 10 kΩ or higher
F152-2 (L-) or F132-7 (FL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR