Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for Radio and Display Type with Single Knob Type) › from 2022.01
RM32K0E _56 Audio / Visual / Telematics _061290 NAVIGATION / MULTI INFO DISPLAY _0522654 NAVIGATION SYSTEM(for Radio and Display Type with Single Knob Type) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Radio and Display Type with Single Knob Type)  Microphone Circuit  


DESCRIPTION

The radio and display receiver assembly and map light assembly (telephone microphone assembly) are connected to each other using the microphone connection detection signal lines.

Using this circuit, the radio and display receiver assembly sends power to the map light assembly (telephone microphone assembly), and the map light assembly (telephone microphone assembly) sends microphone signals to the radio and display receiver assembly.

WIRING DIAGRAM

E381473E36
0.333,2.438 0.75,2.667 0.417,0.229 10 false R2 0.333,2.594 2.313,3.208 1.979,0.615 10 false Map Light Assembly (Telephone Microphone Assembly) 5.427,2.927 5.844,3.156 0.417,0.229 10 false F174 5.406,3.104 7.094,3.719 1.688,0.615 10 false Radio and Display Receiver Assembly 5.948,2.625 6.427,2.854 0.479,0.229 10 false SGND 5.958,1.583 6.375,1.813 0.417,0.229 10 false MIN+ 5.958,1.052 6.49,1.281 0.531,0.229 10 false MACC 5.958,0.531 6.375,0.76 0.417,0.229 10 false SNS 5.677,0.438 6.094,0.667 0.417,0.229 10 false 25 5.677,0.969 6.094,1.198 0.417,0.229 10 false 23 5.688,1.49 6.104,1.719 0.417,0.229 10 false 21 5.677,2 6.094,2.229 0.417,0.229 10 false 22 5.677,2.521 6.094,2.75 0.417,0.229 10 false 24 1.677,1.99 2.094,2.219 0.417,0.229 10 false 7 1.677,1.458 2.094,1.688 0.417,0.229 10 false 8 1.677,0.927 2.094,1.156 0.417,0.229 10 false 9 1.677,0.427 2.094,0.656 0.417,0.229 10 false 1 1.135,1.583 1.635,1.792 0.5,0.208 10 false MCO+ 1.146,2.104 1.646,2.313 0.5,0.208 10 false MCO- 1.125,1.042 1.656,1.271 0.531,0.229 10 false MACC 5.979,2.094 6.396,2.323 0.417,0.229 10 false MIN- 1.156,0.521 1.573,0.75 0.417,0.229 10 false SNS2 3.438,2.354 4.25,2.688 0.813,0.333 10 false (Shielded)

CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM (for Radio and Display Type with Single Knob Type)>PRECAUTION


PROCEDURE

1.CHECK MICROPHONE (OPERATION CHECK)
a.

b.

When a voice is input into the microphone, check that the microphone input level meter changes according to the input voice.

OK:

Check result is normal.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))
2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))
a.

Disconnect the F174 radio and display receiver assembly connector.


b.

Disconnect the R2 map light assembly (telephone microphone assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F174-25 (SNS) - R2-1 (SNS) Always Below 1 Ω
F174-23 (MACC) - R2-9 (MACC) Always Below 1 Ω
F174-21 (MIN+) - R2-8 (MCO+) Always Below 1 Ω
F174-22 (MIN-) - R2-7 (MCO-) Always Below 1 Ω
F174-25 (SNS) - Body ground Always 10 kΩ or higher
F174-23 (MACC) - Body ground Always 10 kΩ or higher
F174-21 (MIN+) - Body ground Always 10 kΩ or higher
F174-22 (MIN-) - Body ground Always 10 kΩ or higher
F174-24 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
a.

Reconnect the F174 radio and display receiver assembly connector.


b.

Reconnect the R2 map light assembly (telephone microphone assembly) connector.


c.
E487361C01
1.427,0.198 1.917,0.479 0.49,0.281 2.01,1.354 2.844,1.646 true 2.5,1.802 1.906,1.365 true 1.979,1.885 1.802,1.375 true 1.521,0.24 1.896,0.438 0.375,0.198 10 false F174 0.177,0.135 0.49,0.333 0.313,0.198 10 false *a 2.813,1.656 3.271,1.854 0.458,0.198 10 false MIN- 1.885,1.917 2.385,2.146 0.5,0.229 10 false SGND 2.354,1.823 2.979,2.021 0.625,0.198 10 false MACC
*a Component with harness connected
(Radio and Display Receiver Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F174-23 (MACC) - Body ground Power switch on (ACC) 4 to 6 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F174-24 (SGND) - Body ground Always Below 1 Ω
F174-22 (MIN-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

NG

4.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)
a.

Remove the map light assembly (telephone microphone assembly).

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT (for TMMT Made)>REMOVAL


b.
E358190C09
2.281,1.094 2.552,0.49 true 2.292,1.427 2.583,1.771 true 0.25,0.198 0.563,0.396 0.313,0.198 10 false *a 2.615,0.385 3.083,0.604 0.469,0.219 10 false SNS 2.583,1.771 3.219,1.958 0.635,0.188 10 false MCO-
*a Component without harness connected
(Map Light Assembly (Telephone Microphone Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (SNS) - 7 (MCO-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

NG

REPLACE MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

5.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)
a.

Reconnect the F174 radio and display receiver assembly connector.


b.

Reconnect the R2 map light assembly (telephone microphone assembly) connector.


c.

Turn the power switch on (ACC).


d.
E358189C03
1.542,0.49 1.969,0.75 0.427,0.26 2.188,1.75 2.708,2.177 true 1.99,1.781 2.208,2.385 true 0.219,0.177 0.531,0.375 0.313,0.198 10 false *a 1.646,0.521 1.958,0.719 0.313,0.198 10 false R2 2.76,2.188 3.198,2.458 0.438,0.271 10 false MCO- 2.115,2.427 2.604,2.698 0.49,0.271 10 false MCO+
*a Component with harness connected
(Map Light Assembly (Telephone Microphone Assembly))


Connect an oscilloscope to terminals 8 (MCO+) and 7 (MCO-) of the R2 map light assembly (telephone microphone assembly) connector.


e.

Check the waveform of the map light assembly (telephone microphone assembly) using the oscilloscope.

Result:
Result Proceed to
A waveform synchronized with the voice input to the map light assembly (telephone microphone assembly) is output. A
A waveform synchronized with the voice input to the map light assembly (telephone microphone assembly) is not output. B




A

B

REPLACE MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)