Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type with Single Knob Type) › from 2022.01
RM32K0E _56 Audio / Visual / Telematics _061817 AUDIO / VIDEO _0525784 AUDIO AND VISUAL SYSTEM(for Radio and Display Type with Single Knob Type) C

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type with Single Knob Type)  B157913  Voice Recognition Microphone1 Circuit Open  


DESCRIPTION

The telephone microphone assembly is connected to the radio and display receiver assembly via voice recognition microphone 1 signal detection line.

This DTC is stored when the radio and display receiver assembly detects disconnection of telephone microphone assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area
B157913 Voice Recognition Microphone1 Circuit Open Voice recognition microphone 1 terminal (SNS) disconnected
(2 trip detection logic)
·

Map light assembly (telephone microphone assembly)

·

Radio and display receiver assembly

·

Harness or connector



WIRING DIAGRAM

E370424E38
1.323,1.063 1.844,1.26 0.521,0.198 10 false SNS2 1.333,1.99 1.854,2.188 0.521,0.198 10 false MCO- 1.823,0.927 2.073,1.115 0.25,0.188 10 false 1 1.844,1.865 2.094,2.052 0.25,0.188 10 false 7 0.521,2.552 0.833,2.729 0.313,0.177 10 false R2 0.51,2.719 2.49,3.135 1.979,0.417 10 false Map Light Assembly (Telephone Microphone Assembly) 5.313,2.74 7.021,3.167 1.708,0.427 10 false Radio and Display Receiver Assembly 5.323,2.563 5.844,2.75 0.521,0.188 10 false F174 5.792,1.042 6.313,1.229 0.521,0.188 10 false SNS 5.781,1.99 6.302,2.177 0.521,0.188 10 false MIN- 5.469,1.906 5.76,2.125 0.292,0.219 10 false 22 5.49,0.917 5.781,1.135 0.292,0.219 10 false 25

CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type with Single Knob Type)>PRECAUTION


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY) - RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.

Disconnect the R2 map light assembly (telephone microphone assembly) connector.


b.

Disconnect the F174 radio and display receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R2-1 (SNS2) - F174-25 (SNS) Always Below 1 Ω
R2-7 (MCO-) - F174-22 (MIN-) Always Below 1 Ω
R2-1 (SNS2) or F174-25 (SNS) - Body ground Always 10 kΩ or higher
R2-7 (MCO-) or F174-22 (MIN-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY (MIN-)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY (MIN-)
a.

With the radio and display receiver assembly connectors connected, disconnect the R2 map light assembly (telephone microphone assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R2-7 (MCO-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY) (SNS, MCO-)

NG

3.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY) (SNS, MCO-)
a.
E469837C01
1.333,1.167 0.833,0.833 true 0.833,1.833 1.333,1.49 true 0.083,0.052 0.396,0.25 0.313,0.198 10 false *a 0.438,0.729 0.854,0.979 0.417,0.25 10 false SNS2 0.417,1.75 1,1.948 0.583,0.198 10 false MCO-
*a Component without harness connected
(Map Light Assembly (Telephone Microphone Assembly))


Remove the map light assembly (telephone microphone assembly).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (SNS2) - 7 (MCO-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPLACE MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)