Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type with Single Knob Type) › from 2022.01
RM32K0E _56 Audio / Visual / Telematics _061817 AUDIO / VIDEO _0525784 AUDIO AND VISUAL SYSTEM(for Radio and Display Type with Single Knob Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type with Single Knob Type)  Radio Wave Reception Failure  


CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type with Single Knob Type)>PRECAUTION


PROCEDURE

1.INSPECT NO. 3 ANTENNA CORD SUB-ASSEMBLY
a.
E482014C01
0.167,0.094 0.479,0.292 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Roof Antenna Assembly)


Prepare for check

i.

Ensure that the connecter between the roof antenna assembly and the No. 3 antenna cord sub-assembly is visible


ii.

Disconnect the connector between the roof antenna assembly and the No. 3 antenna cord sub-assembly.



b.

Inspect for noise

i.

With the connector of the radio and display receiver assembly connected, turn the ignition switch to ON.


ii.

Turn the audio system on and enter radio mode.


iii.

Confirm that noise is output from the speakers when contacting terminal 2 of the No. 3 antenna cord sub-assembly with a screwdriver or metal object such as a thin metal wire.

OK:

Rasping noise occurs.




c.

Measure voltage

i.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
2 - Body ground Receiving radio broadcast 7 to 16 V




Result:
Proceed to
OK
NG



OK

REPLACE ROOF ANTENNA ASSEMBLY

NG

2.INSPECT NO. 2 ANTENNA CORD SUB-ASSEMBLY
2.INSPECT NO. 2 ANTENNA CORD SUB-ASSEMBLY
a.
E215858C92
0.167,0.156 0.479,0.354 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to No. 3 Antenna Cord Sub-assembly)


Prepare for check

i.

Ensure that the connecter between the No. 3 antenna cord sub-assembly and the No. 2 antenna cord sub-assembly is visible


ii.

Disconnect the connector between the No. 3 antenna cord sub-assembly and the No. 2 antenna cord sub-assembly.



b.

Inspect for noise

i.

With the connector of the radio and display receiver assembly connected, turn the ignition switch to ON.


ii.

Turn the audio system on and enter radio mode.


iii.

Confirm that noise is output from the speakers when contacting terminal 3 of the No. 2 antenna cord sub-assembly with a screwdriver or metal object such as a thin metal wire.

OK:

Rasping noise occurs.




c.

Measure voltage

i.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3 - Body ground Receiving radio broadcast 7 to 16 V




Result:
Proceed to
OK
NG



OK

REPLACE NO. 3 ANTENNA CORD SUB-ASSEMBLY

NG

3.INSPECT ANTENNA CORD SUB-ASSEMBLY
3.INSPECT ANTENNA CORD SUB-ASSEMBLY
a.
E215858C93
0.167,0.156 0.479,0.354 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly)


Prepare for check

i.

Ensure that the connector between the No. 2 antenna cord sub-assembly and antenna cord sub-assembly is visible.


ii.

Disconnect the connector between the No. 2 antenna cord sub-assembly and antenna cord sub-assembly.



b.

Inspect for Noise

i.

With the connector of the radio and display receiver assembly connected, turn the ignition switch to ON.


ii.

Turn the audio system on and enter radio mode.


iii.

Confirm that noise is output from the speakers when contacting terminal 3 of the antenna cord sub-assembly with a screwdriver or metal object such as a thin metal wire.

OK:

Rasping noise occurs




c.

Measure voltage

i.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3 - Body ground Receiving radio broadcast 7 to 16 V




Result:
Proceed to
OK
NG



OK

REPLACE NO. 2 ANTENNA CORD SUB-ASSEMBLY

NG

4.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY (ANTENNA)
4.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY (ANTENNA)
a.

Prepare the radio and display receiver assembly for removal.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
RA-1 (ANT+) - Body ground Receiving radio broadcasts 7 to 16 V



c.

Disconnect the RA radio and display receiver assembly connector.


d.

With all other radio and display receiver assembly connectors connected, turn the ignition switch to ON.


e.
E480643C02
1.542,0.177 1.958,0.448 0.417,0.271 1.667,0.24 1.927,0.51 0.26,0.271 10 false RA 0.281,0.156 0.542,0.427 0.26,0.271 10 false *a
*a Component without harness connected
(Radio and Display Receiver Assembly)


Turn the audio system on and enter radio mode.

i.

Confirm that noise is output from the speakers when contacting terminal RA-3 of the radio and display receiver assembly with a screwdriver or metal object such as a thin metal wire.

OK:

Rasping noise occurs.




Result:
Proceed to
OK
NG



OK

REPLACE ANTENNA CORD SUB-ASSEMBLY

NG