Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2022.01
RM32K0E _58 Vehicle Interior _062267 SUPPLEMENTAL RESTRAINT SYSTEMS _0304666 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B166D  Lost Communication with Front Door Pressure Sensor RH  B166E  Front Door Pressure Sensor RH Initialization Incomplete  


DESCRIPTION

The side collision sensor RH circuit (bus 1) consists of the airbag sensor assembly and door side airbag sensor RH.

The door side airbag sensor RH detect impacts to the vehicle and send signals to the airbag sensor assembly to determine if the airbags and pretensioners should be deployed.

These DTCs are stored when a malfunction is detected in the side collision sensor RH circuit (bus 1).

DTC No. Detection Item DTC Detection Condition Trouble Area Test Mode / Check Mode
B166D Lost Communication with Front Door Pressure Sensor RH
·

The airbag sensor assembly detects a line short in the side collision sensor RH circuit (bus 1).

·

The airbag sensor assembly detects a short to ground in the side collision sensor RH circuit (bus 1).

·

The airbag sensor assembly detects a short to B+ in the side collision sensor RH circuit (bus 1).

·

The airbag sensor assembly detects an open in the side collision sensor RH circuit (bus 1).

·

Door side airbag sensor RH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Front door wire RH

·

Door side airbag sensor RH

·

Airbag sensor assembly


Does not apply to test/check mode
B166E Front Door Pressure Sensor RH Initialization Incomplete
·

The airbag sensor assembly detects a line short in the side collision sensor RH circuit (bus 1).

·

The airbag sensor assembly detects a short to ground in the side collision sensor RH circuit (bus 1).

·

The airbag sensor assembly detects a short to B+ in the side collision sensor RH circuit (bus 1).

·

The airbag sensor assembly detects an open in the side collision sensor RH circuit (bus 1).

·

Door side airbag sensor RH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Front door wire RH

·

Door side airbag sensor RH

·

Airbag sensor assembly


Does not apply to test/check mode

DTC Detection Conditions (B166D):
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3
Diagnosis Condition Power switch on (IG) ○ ○ ○
Malfunction Status The airbag sensor assembly detects a line short in the side collision sensor RH circuit (bus 1) ○ - -
The airbag sensor assembly detects a short to ground in the side collision sensor RH circuit (bus 1) - ○ -
The airbag sensor assembly detects a short to B+ in the side collision sensor RH circuit (bus 1) - - ○
Detection Time - - -
Number of Trips 1 trip 1 trip 1 trip

DTC Detection Conditions (B166D):
Vehicle Condition
Pattern 4 Pattern 5 Pattern 6
Diagnosis Condition Power switch on (IG) ○ ○ ○
Malfunction Status The airbag sensor assembly detects an open in the side collision sensor RH circuit (bus 1) ○ - -
Door side airbag sensor RH malfunction - ○ -
Airbag sensor assembly malfunction - - ○
Detection Time - - -
Number of Trips 1 trip 1 trip 1 trip

DTC Detection Conditions (B166E):
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3
Diagnosis Condition Power switch on (IG) ○ ○ ○
Malfunction Status The airbag sensor assembly detects a line short in the side collision sensor RH circuit (bus 1) ○ - -
The airbag sensor assembly detects a short to ground in the side collision sensor RH circuit (bus 1) - ○ -
The airbag sensor assembly detects a short to B+ in the side collision sensor RH circuit (bus 1) - - ○
Detection Time - - -
Number of Trips 1 trip 1 trip 1 trip

DTC Detection Conditions (B166E):
Vehicle Condition
Pattern 4 Pattern 5 Pattern 6
Diagnosis Condition Power switch on (IG) ○ ○ ○
Malfunction Status The airbag sensor assembly detects an open in the side collision sensor RH circuit (bus 1) ○ - -
Door side airbag sensor RH malfunction - ○ -
Airbag sensor assembly malfunction - - ○
Detection Time - - -
Number of Trips 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


WIRING DIAGRAM

C479853E03
0.469,3.104 4.448,3.302 3.979,0.198 10 false Door Side Airbag Sensor RH 0.469,2.917 0.781,3.115 0.313,0.198 10 false I5 1.385,0.896 2,1.094 0.615,0.198 10 false BDR+ 1.417,2.063 2.031,2.26 0.615,0.198 10 false BDR- 1.865,0.75 2.021,0.948 0.156,0.198 10 false 2 1.865,1.948 2.021,2.146 0.156,0.198 10 false 1 3.49,2.063 3.948,2.26 0.458,0.198 10 false IM1 3.49,0.896 3.948,1.094 0.458,0.198 10 false IM1 3.51,0.688 3.823,0.885 0.313,0.198 10 false 22 3.521,1.865 3.833,2.063 0.313,0.198 10 false 40 5.125,0.76 5.438,0.958 0.313,0.198 10 false 25 5.135,1.948 5.448,2.146 0.313,0.198 10 false 26 5.396,0.896 6.01,1.094 0.615,0.198 10 false BBR+ 5.406,2.094 6.021,2.292 0.615,0.198 10 false BBR- 5.125,2.927 5.74,3.125 0.615,0.198 10 false M103 5.135,3.104 6.906,3.375 1.771,0.271 10 false Airbag Sensor Assembly

CAUTION / NOTICE / HINT

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

1.CHECK CONNECTION OF CONNECTORS
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the door side airbag sensor RH. Also check that the connectors that link the floor wire and front door wire RH are properly connected.

OK:

The connectors are properly connected.



Result:
Proceed to
OK
NG



OK

2.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

2.CHECK CONNECTORS
a.
E444929C02
0.396,1.573 0.708,1.729 0.313,0.156 10 false *1 2.583,1.5 2.896,1.656 0.313,0.156 10 false *2 1.125,1.385 1.438,1.542 0.313,0.156 10 false *3 1.656,1.406 1.969,1.563 0.313,0.156 10 false *4
*1 Door Side Airbag Sensor RH
*2 Airbag Sensor Assembly
*3 Front Door Wire RH
*4 Floor Wire


Disconnect the connectors from the airbag sensor assembly and door side airbag sensor RH.


b.

Check that the connectors (on the airbag sensor assembly side and door side airbag sensor RH side) are not damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

3.CHECK DOOR SIDE AIRBAG SENSOR RH

NG

REPLACE FLOOR WIRE OR FRONT DOOR WIRE RH

3.CHECK DOOR SIDE AIRBAG SENSOR RH
a.
C470253C03
1.135,3.531 1.552,3.781 0.417,0.25 0.865,0.573 1.281,0.823 0.417,0.25 1.813,3.958 2.385,2.979 true 2.177,1.094 1.896,0.719 true 1.354,1.167 1.688,0.719 true 1.906,3.979 2.698,3.396 true 1.854,4.271 2.052,4.417 true 0.729,2.167 0.875,2.354 0.146,0.188 10 false F 0.417,2.646 0.625,2.833 0.208,0.188 10 false *1 0.979,2.167 1.115,2.354 0.135,0.188 10 false E 2.031,2.167 2.167,2.354 0.135,0.188 10 false B 1.156,1.969 1.365,2.156 0.208,0.188 10 false *3 1.74,1.979 1.948,2.167 0.208,0.188 10 false *4 2.302,2.177 2.438,2.365 0.135,0.188 10 false A 2.677,2.469 2.885,2.656 0.208,0.188 10 false *2 1.01,0.625 1.271,0.813 0.26,0.188 10 false I5 0.677,0.146 0.885,0.333 0.208,0.188 10 false *a 0.969,1.073 1.49,1.24 0.521,0.167 10 false BDR- 2.25,1.052 2.813,1.219 0.563,0.167 10 false BDR+ 1.177,3.573 1.604,3.74 0.427,0.167 10 false M103 0.948,2.896 1.156,3.083 0.208,0.188 10 false *b 2.104,4.365 2.323,4.51 0.219,0.146 10 false *5 1.427,2.167 1.563,2.333 0.135,0.167 10 false D 1.583,2.167 1.719,2.333 0.135,0.167 10 false C 2.448,2.875 3.01,3.042 0.563,0.167 10 false BBR+ 2.76,3.313 3.281,3.479 0.521,0.167 10 false BBR-
*1 Door Side Airbag Sensor RH
*2 Airbag Sensor Assembly
*3 Front Door Wire RH
*4 Floor Wire
*5 Service Wire
*a Front view of wire harness connector
(to Door Side Airbag Sensor RH)
*b Front view of wire harness connector
(to Airbag Sensor Assembly)


Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
I5-2 (BDR+) - Body ground power switch on (IG) Below 1 V
I5-1 (BDR-) - Body ground power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 25 (BBR+) and 26 (BBR-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I5-2 (BDR+) - I5-1 (BDR-) Always Below 1 Ω



h.

Disconnect the service wire from connector B.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I5-2 (BDR+) - I5-1 (BDR-) Always 1 MΩ or higher
I5-2 (BDR+) - Body ground Always 1 MΩ or higher
I5-1 (BDR-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK DOOR SIDE AIRBAG SENSOR RH

NG

5.CHECK CONNECTORS
4.CHECK DOOR SIDE AIRBAG SENSOR RH
a.
E444928C03
0.719,1.531 1.51,2.167 0.792,0.635 10 false *1 2.573,1.51 2.927,1.917 0.354,0.406 10 false *2
*1 Door Side Airbag Sensor LH
*2 Airbag Sensor Assembly


Connect the connector to the airbag sensor assembly.


b.

Interchange the door side airbag sensor RH with LH and connect the connectors to them.


c.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


d.

Turn the power switch on (IG), and wait for at least 60 seconds.


e.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the power switch off.


g.

Turn the power switch on (IG), and wait for at least 60 seconds.


h.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Result Proceed to
DTC B166D or B166E is output A
DTC B167B or B167C is output B
DTCs B166D, B166E, B167B and B167C are not output C


HINT:

Codes other than DTC B166D, B166E, B167B and B167C may be output at this time, but they are not related to this check.



i.

Turn the power switch off.


j.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


k.

Return the door side airbag sensor LH and RH to their original positions and connect the connectors to them.



A

B

C

5.CHECK CONNECTORS
a.
E444930C02
0.427,1.635 0.74,1.792 0.313,0.156 10 false *1 2.625,1.49 2.938,1.646 0.313,0.156 10 false *2 1.104,1.396 1.417,1.552 0.313,0.156 10 false *3 1.719,1.406 2.031,1.563 0.313,0.156 10 false *4
*1 Door Side Airbag Sensor RH
*2 Airbag Sensor Assembly
*3 Front Door Wire RH
*4 Floor Wire


Disconnect the floor wire connector from the front door wire RH.


b.

Check that the connectors (on the floor wire side and front door wire RH side) are not damaged.


Result:
Proceed to
OK
NG



OK

6.CHECK FLOOR WIRE

NG

REPLACE FLOOR WIRE OR FRONT DOOR WIRE RH

6.CHECK FLOOR WIRE
a.
C470309C03
1.083,3.583 1.5,3.833 0.417,0.25 0.979,0.635 1.396,0.885 0.417,0.25 0.302,0.594 0.667,0.875 0.365,0.281 1.625,0.833 1.927,1.177 true 1.792,3.927 2.354,3.01 true 1.906,3.938 2.604,3.292 true 1.625,0.719 1.917,0.271 true 2.083,4.427 1.823,4.219 true 1.979,1.115 2.667,1.323 0.688,0.208 10 false BDR- 1.969,0.167 2.396,0.563 0.427,0.396 10 false BDR+ 2.292,2.198 2.479,2.427 0.188,0.229 10 false A 2.073,2.188 2.26,2.417 0.188,0.229 10 false B 1.604,2.177 1.792,2.406 0.188,0.229 10 false C 1.396,2.177 1.583,2.406 0.188,0.229 10 false D 0.958,2.188 1.177,2.448 0.219,0.26 10 false E 0.729,2.198 0.948,2.458 0.219,0.26 10 false F 2.635,2.469 2.896,2.698 0.26,0.229 10 false *2 0.406,2.667 0.667,2.896 0.26,0.229 10 false *1 0.385,0.646 0.719,0.823 0.333,0.177 10 false IM1 0.302,0.125 0.563,0.354 0.26,0.229 10 false *a 0.927,2.885 1.188,3.115 0.26,0.229 10 false *b 1.125,1.948 1.385,2.177 0.26,0.229 10 false *3 1.771,1.948 2.031,2.177 0.26,0.229 10 false *4 1.135,3.625 1.542,3.854 0.406,0.229 10 false M103 2.396,2.917 3.083,3.125 0.688,0.208 10 false BBR+ 2.667,3.177 3.24,3.385 0.573,0.208 10 false BBR- 2.125,4.354 2.385,4.583 0.26,0.229 10 false *5
*1 Door Side Airbag Sensor RH
*2 Airbag Sensor Assembly
*3 Front Door Wire RH
*4 Floor Wire
*5 Service Wire
*a Front view of wire harness connector
(to Front Door Wire RH)
*b Front view of wire harness connector
(to Airbag Sensor Assembly)


Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
IM1-22 (BDR+) - Body ground power switch on (IG) Below 1 V
IM1-40 (BDR-) - Body ground power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 25 (BBR+) and 26 (BBR-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
IM1-22 (BDR+) - IM1-40 (BDR-) Always Below 1 Ω



h.

Disconnect the service wire from connector B.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
IM1-22 (BDR+) - IM1-40 (BDR-) Always 1 MΩ or higher
IM1-22 (BDR+) - Body ground Always 1 MΩ or higher
IM1-40 (BDR-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE FRONT DOOR WIRE RH

NG

REPLACE FLOOR WIRE