Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › REAR VIEW MONITOR SYSTEM › from 2022.01
RM32K0E _56 Audio / Visual / Telematics _060599 PARK ASSIST / MONITORING _0303650 REAR VIEW MONITOR SYSTEM U

PARK ASSIST / MONITORING  REAR VIEW MONITOR SYSTEM  TERMINALS OF ECU  


REAR TELEVISION CAMERA ASSEMBLY


a.

Disconnect the S11 rear television camera assembly connector.

E292772E09
3.26,0.115 3.854,0.375 0.594,0.26 3.448,0.156 3.76,0.354 0.313,0.198 10 false S11


b.

Measure the voltage of each terminal of the wire harness side connector.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
S11-6 (CB+) - Body ground G - Body ground*1
B - Body ground*2
Power source Power switch on (ACC) 5.5 to 7.05 V

*1: except TMC Made 6 Speakers

*2: for TMC Made 6 Speakers


If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the S11 rear television camera assembly connector.


d.

Measure the resistance and check for pulses at each terminal of the connector.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
S11-3 (CV+) - S11-2 (CV-) W - R*1
R - W*2
Video signal Power switch on (IG)
Shift lever in R
Camera lens not covered, displaying an image
Pulse generation
(Refer to waveform 1)
Power switch on (IG)
Shift lever in R
Camera lens covered, blacking out the screen
Pulse generation
(Refer to waveform 2)
S11-5 (CGND) - Body ground B - Body ground*1
G - Body ground*2
Camera ground Always Below 1 Ω

*1: except TMC Made 6 Speakers

*2: for TMC Made 6 Speakers


HINT:

A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the radio and display receiver assembly with the connector connected.


If the result is not as specified, the rear television camera assembly may be malfunctioning.


e.
E265840C29
0.813,2 1.125,1.594 true 1.469,1.969 1.24,1.49 true 1.552,4.125 1.271,3.542 true 0.833,4.115 1.146,3.583 true 0.229,0.229 0.542,0.427 0.313,0.198 10 false *a 0.396,1.052 0.76,1.313 0.365,0.26 10 false GND 0.396,3.208 0.76,3.469 0.365,0.26 10 false GND 0.26,2.271 0.625,2.531 0.365,0.26 10 false *b 0.646,4.073 1.01,4.333 0.365,0.26 10 false *c 0.656,1.979 1.021,2.24 0.365,0.26 10 false *c 1.51,1.969 1.875,2.229 0.365,0.26 10 false *d 1.542,4.156 1.906,4.417 0.365,0.26 10 false *d
*a Waveform 1 (camera lens is not covered, displaying an image)
*b Waveform 2 (camera lens is covered, blacking out the screen)
*c Synchronization Signal
*d Video Waveform


Reference (Oscilloscope waveform):

HINT:

A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the radio and display receiver assembly with the connector connected.


i.

Waveform 1 (camera lens is not covered, displaying an image)

Item Content
Measurement terminal S11-3 (CV+) - S11-2 (CV-)
Measurement setting 200 mV/DIV., 50 μs./DIV.
Condition Power switch on (IG), shift lever in R

HINT:
·

The video waveform changes according to the image sent by the rear television camera assembly.

·

The video waveform is constantly output when the power switch on (ACC).




ii.

Waveform 2 (camera lens is covered, blacking out the screen)

Item Content
Measurement terminal S11-3 (CV+) - S11-2 (CV-)
Measurement setting 200 mV/DIV., 50 μs./DIV.
Condition Power switch on (IG), shift lever in R

HINT:
·

The video waveform changes according to the image sent by the rear television camera assembly.

·

The video waveform is constantly output when the power switch on (ACC).






RADIO AND DISPLAY RECEIVER ASSEMBLY (w/ Dual Knob Type)


HINT:

Check from the rear of the connector while it is connected to the components.


E425775N03
1.292,0.292 1.792,0.542 0.5,0.25 3.229,0.271 3.729,0.521 0.5,0.25 1.385,0.333 1.844,0.531 0.458,0.198 10 false F129 3.313,0.302 3.771,0.5 0.458,0.198 10 false F131

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F131-26 (CSLD) - Body ground Shield - Body ground Shield ground Always Below 1 V
F131-27 (CGND) - Body ground G - Body ground*1
B - Body ground*2
Camera ground Always Below 1 V
F131-28 (V+) - F129-1 (GND1) R - LA*1
W - LA*2
Video signal Power switch on (IG)
Shift lever in R
Camera lens not covered, displaying an image
Pulse generation
(Refer to waveform 1)
Power switch on (IG)
Shift lever in R
Camera lens covered, blacking out screen
Pulse generation
(Refer to waveform 2)
F131-29 (V-) - F129-1 (GND1) W - LA*1
R - LA*2
Ground Always Below 1 V
F131-30 (CA+) - F129-1 (GND1) B - LA*1
G - LA*2
Rear television camera assembly power supply Power switch on (ACC) 5.5 to 7.05 V

*1: for TMC Made

*2: for TMMT Made


a.

Reference (Oscilloscope waveform):

i.
E265840C29
0.813,2 1.125,1.594 true 1.469,1.969 1.24,1.49 true 1.552,4.125 1.271,3.542 true 0.833,4.115 1.146,3.583 true 0.229,0.229 0.542,0.427 0.313,0.198 10 false *a 0.396,1.052 0.76,1.313 0.365,0.26 10 false GND 0.396,3.208 0.76,3.469 0.365,0.26 10 false GND 0.26,2.271 0.625,2.531 0.365,0.26 10 false *b 0.646,4.073 1.01,4.333 0.365,0.26 10 false *c 0.656,1.979 1.021,2.24 0.365,0.26 10 false *c 1.51,1.969 1.875,2.229 0.365,0.26 10 false *d 1.542,4.156 1.906,4.417 0.365,0.26 10 false *d
*a Waveform 1 (camera lens not covered, displaying an image)
*b Waveform 2 (camera lens covered, blacking out the screen)
*c Synchronization Signal
*d Video Waveform


Waveform 1 (camera lens not covered, displaying an image)

Item Content
Measurement terminal F131-28 (V+) - F129-1 (GND1)
Measurement setting 200 mV/DIV., 50 μs/DIV.
Condition Power switch on (IG), shift lever in R

HINT:
·

The video waveform changes according to the image sent by the rear television camera assembly.

·

The video waveform is constantly output when the ignition switch is turned to ACC.




ii.

Waveform 2 (camera lens covered, blacking out the screen)

Item Content
Measurement terminal F131-28 (V+) - F129-1 (GND1)
Measurement setting 200 mV/DIV., 50 μs/DIV.
Condition Power switch on (IG), shift lever in R

HINT:
·

The video waveform changes according to the image sent by the rear television camera assembly.

·

The video waveform is constantly output when the power switch on (ACC).






RADIO AND DISPLAY RECEIVER ASSEMBLY (w/ Single Knob Type)


HINT:

Check from the rear of the connector while it is connected to the components.


E469834N03
1.708,0.708 2.177,0.969 0.469,0.26 3.417,0.708 3.833,0.958 0.417,0.25 3.479,0.75 4.094,0.948 0.615,0.198 10 false F174 1.781,0.76 2.396,0.958 0.615,0.198 10 false F129

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F174-26 (CSLD) - Body ground Shield - Body ground Shield ground Always Below 1 V
F174-27 (CGND) - Body ground B - Body ground Camera ground Always Below 1 V
F174-28 (V+) - F129-1 (GND1) R - LA Video signal Power switch on (IG)
Shift lever in R
Camera lens not covered, displaying an image
Pulse generation
(Refer to waveform 1)
Power switch on (IG)
Shift lever in R
Camera lens covered, blacking out screen
Pulse generation
(Refer to waveform 2)
F174-29 (V-) - F129-1 (GND1) W - LA Ground Always Below 1 V
F174-30 (CA+) - F129-1 (GND1) G - LA Rear television camera assembly power supply Power switch on (ACC) 5.5 to 7.05 V

a.

Reference (Oscilloscope waveform):

i.
E265840C29
0.813,2 1.125,1.594 true 1.469,1.969 1.24,1.49 true 1.552,4.125 1.271,3.542 true 0.833,4.115 1.146,3.583 true 0.229,0.229 0.542,0.427 0.313,0.198 10 false *a 0.396,1.052 0.76,1.313 0.365,0.26 10 false GND 0.396,3.208 0.76,3.469 0.365,0.26 10 false GND 0.26,2.271 0.625,2.531 0.365,0.26 10 false *b 0.646,4.073 1.01,4.333 0.365,0.26 10 false *c 0.656,1.979 1.021,2.24 0.365,0.26 10 false *c 1.51,1.969 1.875,2.229 0.365,0.26 10 false *d 1.542,4.156 1.906,4.417 0.365,0.26 10 false *d
*a Waveform 1 (camera lens not covered, displaying an image)
*b Waveform 2 (camera lens covered, blacking out the screen)
*c Synchronization Signal
*d Video Waveform


Waveform 1 (camera lens not covered, displaying an image)

Item Content
Measurement terminal F174-28 (V+) - F129-1 (GND1)
Measurement setting 200 mV/DIV., 50 μs/DIV.
Condition Power switch on (IG), shift lever in R

HINT:
·

The video waveform changes according to the image sent by the rear television camera assembly.

·

The video waveform is constantly output when the ignition switch is turned to ACC.




ii.

Waveform 2 (camera lens covered, blacking out the screen)

Item Content
Measurement terminal F174-28 (V+) - F129-1 (GND1)
Measurement setting 200 mV/DIV., 50 μs/DIV.
Condition Power switch on (IG), shift lever in R

HINT:
·

The video waveform changes according to the image sent by the rear television camera assembly.

·

The video waveform is constantly output when the power switch on (ACC).