Home › Vehicle Exterior › BODY PANEL › REAR FLOOR PAN
BM32H0E _01 Vehicle Exterior _060349 BODY PANEL _0295814 REAR FLOOR PAN F

BODY PANEL  REAR FLOOR PAN  ASSEMBLY REPLACEMENT  


K137825

With the body lower back panel assembly removed.


REMOVAL


Symbol Meaning
K108818

Remove Weld Points

K137694

K137704C01
0.208,0.198 0.521,0.354 0.313,0.156 10 false *A
*A LH Side - -


K137708C01
0.208,0.198 0.521,0.354 0.313,0.156 10 false *A
*A RH Side - -



INSTALLATION


Symbol Meaning
K108823

Plug Weld

a.

Before temporarily installing the new parts, weld the rear floor pan, rear floor panel reinforcement assembly, spare wheel clamp bracket and weld bolts with the standard number of welding points.

K137711C01
2.708,0.948 2.052,0.615 2.052,0.615 1.813,0.615 false 1.854,3.25 1.615,3.448 1.615,3.448 1.406,3.448 false 5.802,3.49 5.563,3.49 5.563,3.49 5.25,3.25 false 3.677,1.969 4.323,0.625 4.323,0.625 4.594,0.625 false 2.26,7.281 3.094,7.281 3.094,7.281 3.094,6.927 false 5.042,7.271 3.938,7.271 3.938,7.271 3.938,5.927 false 2.667,7.281 2.667,6.073 false 4.625,7.271 4.625,6.458 false 4,7.271 4,6.917 false 1.979,2.677 1.469,2.448 1.469,2.448 1.26,2.448 false 5.896,2.385 5.677,2.385 5.677,2.385 5.135,2.667 false 0.906,0.406 1.219,0.563 0.313,0.156 10 false *A 0.896,4.073 1.208,4.229 0.313,0.156 10 false *B 1.646,0.51 1.958,0.667 0.313,0.156 10 false *1 1.219,3.344 1.531,3.5 0.313,0.156 10 false *2 4.646,0.521 4.958,0.677 0.313,0.156 10 false *3 2.083,7.167 2.396,7.323 0.313,0.156 10 false *4 5.833,3.385 6.146,3.542 0.313,0.156 10 false *2 5.083,7.167 5.396,7.323 0.313,0.156 10 false *4 1.083,2.344 1.396,2.5 0.313,0.156 10 false *4 5.938,2.292 6.25,2.448 0.313,0.156 10 false *4
*A Upper Face *B Lower Face
*1 REAR FLOOR PAN *2 REAR FLOOR PANEL REINFORCEMENT ASSEMBLY
*3 SPARE WHEEL CLAMP BRACKET *4 WELD BOLTS


K137699

K137706C01
0.208,0.208 0.521,0.365 0.313,0.156 10 false *A
*A LH Side - -


K137710C01
0.208,0.208 0.521,0.365 0.313,0.156 10 false *A
*A RH Side - -



b.

After welding, apply body sealer and undercoating to the corresponding parts. (See the painting/coating)


c.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.