Home › Vehicle Exterior › BODY PANEL › REAR FLOOR UPPER CENTER CROSSMEMBER
BM32H0E _01 Vehicle Exterior _060349 BODY PANEL _0295841 REAR FLOOR UPPER CENTER CROSSMEMBER F

BODY PANEL  REAR FLOOR UPPER CENTER CROSSMEMBER  ASSEMBLY REPLACEMENT  


K137827

REMOVAL


Symbol Meaning
K108818

Remove Weld Points
K108826

Cut with Disc Sander etc.

a.

Remove the A and B.

K137811C01
0.458,2.094 0.708,2.094 0.708,2.094 1.24,1.885 false 5.781,1.865 6.365,2.115 6.365,2.115 6.604,2.115 false 0.302,1.979 0.615,2.135 0.313,0.156 10 false A 6.667,2 6.979,2.156 0.313,0.156 10 false B 0.229,3.333 0.542,3.49 0.313,0.156 10 false *A 3.667,3.333 3.979,3.49 0.313,0.156 10 false *B
*A LH Side *B RH Side



b.

Roughly cut open the panel so that the adhesive can be reached. Cut through the adhesive with a cut chisel to remove the panel.

HINT:

In cases where the adhesive cannot be removed with a cut chisel, heat the adhesive with an industrial heater gun or gas burner taking care not to cause panel deformation by overheating.


K138115C01
0,0 0,0 false
K108837

Adhesive - -



c.

Remove the A.

K137813C01
0.385,1.344 0.604,1.344 0.604,1.344 1.385,1.813 false 0.25,1.24 0.406,1.438 0.156,0.198 10 false A



INSTALLATION


Symbol Meaning
K108818

Remove Weld Points
K108823

Plug Weld
K108830

Fillet Weld

a.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)


b.

Remove A and B from the new parts.

K137731C01
1.083,0.604 1.313,0.604 1.313,0.604 1.865,0.938 false 5.969,0.604 5.729,0.604 5.729,0.604 5.219,0.917 false 3.99,0.385 3.75,0.385 3.75,0.385 3.385,0.833 false 0.938,0.5 1.25,0.656 0.313,0.156 10 false A 3.677,2.094 3.99,2.25 0.313,0.156 10 false *B 4.031,0.281 4.344,0.438 0.313,0.156 10 false *1 0.229,2.094 0.542,2.25 0.313,0.156 10 false *A 6.042,0.5 6.354,0.656 0.313,0.156 10 false B
*A LH Side *B RH Side
*1 CENTER FLOOR CROSS MEMBER NO. 2 - -



c.

Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115).

HINT:
·

Apply a light coat of adhesive around the plug welding points.

·

Apply enough adhesive to the panels.



K138115C02
0,0 0,0 false
K108837

Adhesive - -



d.

Weld the A to the vehicle side.

K137814C01
0.344,1.26 0.542,1.26 0.542,1.26 1.385,1.813 false 0.208,1.146 0.365,1.344 0.156,0.198 10 false A


e.

Weld the A and B to the vehicle side.

K137812C01
0.458,1.99 0.677,1.99 0.677,1.99 1.156,1.771 false 5.865,1.75 6.448,1.979 6.448,1.979 6.667,1.979 false 0.24,3.333 0.552,3.49 0.313,0.156 10 false *A 3.677,3.333 3.99,3.49 0.313,0.156 10 false *B 2.698,3.594 3.01,3.75 0.313,0.156 10 false *a 4.292,3.594 4.604,3.75 0.313,0.156 10 false *a 0.313,1.875 0.625,2.031 0.313,0.156 10 false A 6.719,1.865 7.031,2.021 0.313,0.156 10 false B
*A LH Side *B RH Side
*a 27 mm (1.06 in.) - -



f.

After welding, apply body sealer to the corresponding parts. (See the painting/coating)


g.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.