Home › Vehicle Exterior › BODY PANEL › CENTER BODY PILLAR(for TMC Made)
BM32H0E _01 Vehicle Exterior _060349 BODY PANEL _0300238 CENTER BODY PILLAR(for TMC Made) F

BODY PANEL  CENTER BODY PILLAR(for TMC Made)  CUT AND JOIN REPLACEMENT SECTIONS  


K138027

REMOVAL


Symbol Meaning
K108818

Remove Weld Points
K108820

Remove Weld Points
K108826

Cut with Disc Sander etc.
K108827

Cut and Join Location
K108828

Cut Location for Supply Parts

a.

Do not butt weld or heat repair because the heat decreases the strength of areas where ultra high strength steel is used. (See the introduction)


b.

Be careful when cutting as foamed sealing material is located near the cutting position.

K138714C01
0,0 0,0 false
K108840

Foamed Sealing Material - -


K138715C05
5.292,0.448 5.604,0.604 0.313,0.156 10 false *a
*a 20 mm (0.79 in.) - -


K138716C02
1.458,4.271 1.771,4.427 0.313,0.156 10 false *a
*a 175 mm (6.89 in.) - -


K137856

K137857C01
3.479,1.031 3.792,1.188 0.313,0.156 10 false *a
*a 20 mm (0.79 in.) - -



c.

When replace only the outer panel, please cut off a necessary range depending on a damage range.

i.

Carefully cut the outer panel so not to damage the reinforcement.


ii.

Make sure that butt welding does not heat-affect the reinforcement when welding the outer panel.




INSTALLATION


Symbol Meaning
K108823

Plug Weld
K108825

Plug Weld
K108830

Fillet Weld
K108831

Butt Weld

a.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.


b.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)


c.

Weld the center body pillar reinforce sub-assembly lower to the vehicle side.

K137858C01
2.99,1.958 2.469,1.667 2.469,1.667 2.177,1.667 false 2,1.583 2.313,1.74 0.313,0.156 10 false *1 2.667,2.635 2.979,2.792 0.313,0.156 10 false *a 4.135,2.573 4.448,2.729 0.313,0.156 10 false *b
*1 CENTER BODY PILLAR REINFORCE SUB-ASSEMBLY LOWER - -
*a 12 mm (0.47 in.) *b 15 mm (0.59 in.)



d.

Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115).

HINT:
·

Apply a light coat of adhesive around the plug welding points.

·

Apply enough adhesive to the panels.



K138110C01
0,0 0,0 false
K108837

Adhesive - -



e.

Weld the center body pillar reinforcement sub-assembly to the vehicle side.

K137859C01
2.604,2.917 2.99,2.917 2.99,2.917 3.469,3.135 false 2.417,2.823 2.729,2.979 0.313,0.156 10 false *1
*1 CENTER BODY PILLAR REINFORCEMENT SUB-ASSEMBLY - -
*a Ultra High Strength Steel Welding Point - -


Follow the welding conditions below when welding ultra high strength steel to assure sufficient weld strength. (When repairing this model)

When welding 2 panels together including 1500 MPa ultra high strength steel.

*a: Plug weld Plug diameter 10 mm (0.39 in.)
Wire type AWS A5.18 ER70S-3
Shield gas Metal active gas

NOTICE:

Be sure to use Metal active gas (Ar 80% + CO2 20%) as the shield gas when plug welding.Sufficient weld strength cannot be assured when using 100% CO2 shield gas.




f.

Be careful when welding as foamed sealing material is located near the area that is cut and joined together.

K138720C01
0,0 0,0 false
K108840

Foamed Sealing Material - -



g.

Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115).

HINT:
·

Apply a light coat of adhesive around the plug welding points.

·

Apply enough adhesive to the panels.



K138719C01
0,0 0,0 false
K108837

Adhesive - -



h.

Weld the center body pillar outer to the vehicle side.

K138717C02
3.573,2.656 3.094,2.406 3.094,2.406 2.75,2.406 false 2.573,2.313 2.885,2.469 0.313,0.156 10 false *1
*1 CENTER BODY PILLAR OUTER - -
*a Ultra High Strength Steel Welding Point - -


Follow the welding conditions below when welding ultra high strength steel to assure sufficient weld strength. (When repairing this model)

When welding more than 3 panels together including 1500 MPa ultra high strength steel. (When plug welding a third panel to 2 panels which are welded under the conditions described above.)

*a: Plug weld Plug diameter Same as the standard method (See the introduction)
Wire type AWS A5.18 ER70S-3
Shield gas Metal active gas

NOTICE:

Be sure to use Metal active gas (Ar 80% + CO2 20%) as the shield gas when plug welding.Sufficient weld strength cannot be assured when using 100% CO2 shield gas.




i.

After welding, apply the foamed sealing material to the corresponding parts. (See the painting/coating)


j.

After welding, apply body sealer to the corresponding parts. (See the painting/coating)


k.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.