Home › Vehicle Exterior › BODY PANEL › QUARTER WHEEL HOUSING OUTER PANEL(for TMC Made)
BM32H0E _01 Vehicle Exterior _060349 BODY PANEL _0300239 QUARTER WHEEL HOUSING OUTER PANEL(for TMC Made) F

BODY PANEL  QUARTER WHEEL HOUSING OUTER PANEL(for TMC Made)  ASSEMBLY REPLACEMENT  


K137820

With the quarter panel assembly removed.


REMOVAL


Symbol Meaning
K108818

Remove Weld Points
K108819

Remove Weld Points
K108820

Remove Weld Points
K108826

Cut with Disc Sander etc.
K108827

Cut and Join Location

a.

Roughly cut open the panel so that the adhesive can be reached. Cut through the adhesive with a cut chisel to remove the panel.

HINT:

In cases where the adhesive cannot be removed with a cut chisel, heat the adhesive with an industrial heater gun or gas burner taking care not to cause panel deformation by overheating.


K138634C01
0.208,0.208 0.521,0.365 0.313,0.156 10 false *A
*A LH - -
K108837

Adhesive - -



b.

Remove the A.

HINT:

B indicates weld to remove for easier removal.


K138635C01
1.604,2.74 2.365,3.458 2.365,3.458 2.552,3.458 false 0.208,0.208 0.521,0.365 0.313,0.156 10 false *A 0.573,0.625 0.885,0.781 0.313,0.156 10 false B: 2.594,3.365 2.75,3.563 0.156,0.198 10 false A
*A LH - -



c.

Remove the quarter wheel house reinforcement inner.

HINT:

A indicates weld to remove for easier removal.


K138636C01
3.229,2.563 5.469,2.135 5.469,2.135 5.76,2.135 false 0.208,0.208 0.521,0.365 0.313,0.156 10 false *A 5.833,2.042 6.146,2.198 0.313,0.156 10 false *1 1.479,3.073 1.792,3.229 0.313,0.156 10 false A:
*A LH - -
*1 QUARTER WHEEL HOUSE REINFORCEMENT INNER - -



d.

After removing the A, remove the rear wheel house panel outer.

K138637C01
1.844,2.063 2.042,2.063 2.042,2.063 2.823,2.458 false 2.042,1.625 2.24,1.625 2.24,1.625 3.26,2.073 false 0.208,0.208 0.521,0.365 0.313,0.156 10 false *A 1.667,1.969 1.979,2.125 0.313,0.156 10 false *1 2.635,1.313 2.948,1.469 0.313,0.156 10 false *a 1.896,1.531 2.208,1.688 0.313,0.156 10 false A
*A LH - -
*1 REAR WHEEL HOUSE PANEL OUTER - -
*a 90 mm (3.54 in.) - -


K137657C01
0.208,0.208 0.521,0.365 0.313,0.156 10 false *A
*A LH - -



e.

Roughly cut open the panel so that the adhesive can be reached. Cut through the adhesive with a cut chisel to remove the panel.

HINT:

In cases where the adhesive cannot be removed with a cut chisel, heat the adhesive with an industrial heater gun or gas burner taking care not to cause panel deformation by overheating.


K138638C01
0.208,0.208 0.521,0.365 0.313,0.156 10 false *A
*A LH - -
K108837

Adhesive - -


K138639C01
0.208,0.208 0.521,0.365 0.313,0.156 10 false *A
*A LH - -



f.

Roughly cut open the panel so that the adhesive can be reached. Cut through the adhesive with a cut chisel to remove the panel.

HINT:

In cases where the adhesive cannot be removed with a cut chisel, heat the adhesive with an industrial heater gun or gas burner taking care not to cause panel deformation by overheating.


K138640C01
0.208,0.208 0.521,0.365 0.313,0.156 10 false *A
*A RH - -
K108837

Adhesive - -



g.

Remove the A.

HINT:

B indicates weld to remove for easier removal.


K138641C01
1.49,3.583 1.646,3.583 1.646,3.583 2.333,2.677 false 0.208,0.208 0.521,0.365 0.313,0.156 10 false *A 2.917,0.719 3.229,0.875 0.313,0.156 10 false B: 1.365,3.49 1.677,3.646 0.313,0.156 10 false A
*A RH - -



h.

Remove the quarter wheel house reinforcement inner.

HINT:

A indicates weld to remove for easier removal.


K138642C01
1.49,2 1.74,2 1.74,2 3.76,2.542 false 0.208,0.208 0.521,0.365 0.313,0.156 10 false *A 1.313,1.917 1.625,2.073 0.313,0.156 10 false *1 4.979,2.646 5.292,2.802 0.313,0.156 10 false A:
*A RH - -
*1 QUARTER WHEEL HOUSE REINFORCEMENT INNER - -



i.

After removing the A, remove the rear wheel house panel outer.

K138643C01
4.5,2.313 5.438,1.979 5.438,1.979 5.625,1.979 false 3.969,1.885 5.01,1.552 5.01,1.552 5.177,1.552 false 0.208,0.208 0.521,0.365 0.313,0.156 10 false *A 5.688,1.906 6,2.063 0.313,0.156 10 false *1 4.604,1.24 4.917,1.396 0.313,0.156 10 false *a 5.24,1.469 5.552,1.625 0.313,0.156 10 false A
*A RH - -
*1 REAR WHEEL HOUSE PANEL OUTER - -
*a 90 mm (3.54 in.) - -


K137670C01
0.208,0.208 0.521,0.365 0.313,0.156 10 false *A
*A RH - -



j.

Roughly cut open the panel so that the adhesive can be reached. Cut through the adhesive with a cut chisel to remove the panel.

HINT:

In cases where the adhesive cannot be removed with a cut chisel, heat the adhesive with an industrial heater gun or gas burner taking care not to cause panel deformation by overheating.


K138644C01
0.208,0.208 0.521,0.365 0.313,0.156 10 false *A
*A RH - -
K108837

Adhesive - -


K138645C01
0.208,0.208 0.521,0.365 0.313,0.156 10 false *A
*A RH - -




INSTALLATION


Symbol Meaning
K108821

Spot Weld
K108823

Plug Weld
K108824

Plug Weld
K108825

Plug Weld
K108831

Butt Weld
K108835

Assembly Mark

a.

For positioning of the new parts, align the installation standard holes of the outer panel and the inner panel.

K138646C01
0.208,0.208 0.521,0.365 0.313,0.156 10 false *A
*A LH - -



b.

Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115).

HINT:
·

Apply a light coat of adhesive around the plug welding points.

·

Apply enough adhesive to the panels.



K138638C01
0.208,0.208 0.521,0.365 0.313,0.156 10 false *A
*A LH - -
K108837

Adhesive - -



c.

Weld the rear wheel house panel outer outer and quarter wheel house brace No. 2 to the vehicle side.

K138647C01
3.125,2.104 4.844,1.052 4.844,1.052 5.031,1.052 false 3.74,2.688 5.458,1.938 5.458,1.938 5.646,1.938 false 0.208,0.208 0.521,0.365 0.313,0.156 10 false *A 5.094,0.969 5.406,1.125 0.313,0.156 10 false *1 5.698,1.854 6.01,2.01 0.313,0.156 10 false *2
*A LH - -
*1 REAR WHEEL HOUSE PANEL OUTER *2 QUARTER WHEEL HOUSE BRACE NO. 2



d.

Weld the A to the vehicle side.

K138648C01
3.313,1.99 1.927,1.385 1.927,1.385 1.719,1.385 false 0.198,0.198 0.51,0.354 0.313,0.156 10 false *A 1.583,1.302 1.896,1.458 0.313,0.156 10 false A
*A LH - -


K137658C01
0.208,0.219 0.521,0.375 0.313,0.156 10 false *A
*A LH - -



e.

Weld the quarter wheel house reinforcement inner to the vehicle side.

K138649C01
3.24,2.458 5.438,1.729 5.438,1.729 5.646,1.729 false 0.208,0.208 0.521,0.365 0.313,0.156 10 false *A 5.708,1.646 6.021,1.802 0.313,0.156 10 false *1
*A LH - -
*1 QUARTER WHEEL HOUSE REINFORCEMENT INNER - -



f.

Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115).

HINT:

Apply enough adhesive to the panels.


K138634C01
0.208,0.208 0.521,0.365 0.313,0.156 10 false *A
*A LH - -
K108837

Adhesive - -



g.

Weld the A to the vehicle side.

K138650C01
1.604,2.76 2.479,3.51 2.479,3.51 2.677,3.51 false 0.208,0.208 0.521,0.365 0.313,0.156 10 false *A 2.729,3.417 3.042,3.573 0.313,0.156 10 false A
*A LH - -



h.

For positioning of the new parts, align the installation standard holes of the outer panel and the inner panel.

K138651C01
0.208,0.208 0.521,0.365 0.313,0.156 10 false *A
*A RH - -



i.

Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115).

HINT:
·

Apply a light coat of adhesive around the plug welding points.

·

Apply enough adhesive to the panels.



K138644C01
0.208,0.208 0.521,0.365 0.313,0.156 10 false *A
*A RH - -
K108837

Adhesive - -



j.

Weld the rear wheel house panel outer and quarter wheel house brace No. 2 to the vehicle side.

K138652C01
2.76,2.354 4.313,1.729 4.313,1.729 4.51,1.729 false 0.833,2.979 0.813,4.354 0.813,4.354 0.958,4.354 false 0.208,0.208 0.521,0.365 0.313,0.156 10 false *A 4.563,1.656 4.875,1.813 0.313,0.156 10 false *1 1.01,4.281 1.323,4.438 0.313,0.156 10 false *2
*A RH - -
*1 REAR WHEEL HOUSE PANEL OUTER *2 QUARTER WHEEL HOUSE BRACE NO. 2



k.

Weld the A to the vehicle side.

K138653C01
3.896,1.719 5.167,1.365 5.167,1.365 5.385,1.365 false 0.208,0.208 0.521,0.365 0.313,0.156 10 false *A 5.448,1.281 5.76,1.438 0.313,0.156 10 false A
*A RH - -


K137671C01
0.208,0.208 0.521,0.365 0.313,0.156 10 false *A
*A RH - -



l.

Weld the quarter wheel house reinforcement inner to the vehicle side.

K138654C01
1.344,1.813 1.563,1.813 1.563,1.813 3.74,2.531 false 0.208,0.208 0.521,0.365 0.313,0.156 10 false *A 1.156,1.719 1.469,1.875 0.313,0.156 10 false *1
*A RH - -
*1 QUARTER WHEEL HOUSE REINFORCEMENT INNER - -



m.

Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115).

HINT:

Apply enough adhesive to the panels.


K138640C01
0.208,0.208 0.521,0.365 0.313,0.156 10 false *A
*A RH - -
K108837

Adhesive - -



n.

Weld the A to the vehicle side.

K138655C01
1.49,3.5 1.656,3.5 1.656,3.5 2.323,2.635 false 0.219,0.219 0.531,0.375 0.313,0.156 10 false *A 1.292,3.417 1.604,3.573 0.313,0.156 10 false *A
*A RH - -



o.

After welding, apply body sealer and undercoating to the corresponding parts. (See the painting/coating)


p.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.